NF Tab
The NF (Network Function) Producer/ Consumer tab is used in the various interfaces of the AMF Nodal, AMF Node, Service Based Nodal, Service Based Node, SMF Nodal, and SMF Node test cases. About the 5G Application.
Per 3GPP TS 23.501, 23.502 and 29.5xx.
|
NF Producer
|
NF Consumer/Producer
NF Producer NEF (Nnef)
NF Consumer SMF-NEF
NEF-CAPIF |
|
NF Producer
Location Data
|
NF Consumer (Additional data fields when Test NRF (Nnrf) and NRF Interface are enabled) Nnrf Client NF Consumer (Additional data fields when NRF Interface is enabled on AMF Node, SMF Nodal/SMF Node and Service Based Nodal)
Nnrf Client
NF Consumer / Producer (Additional data fields when Indirect Communication and Delegate NF Discovery And Selection are enabled on Service Based Nodal / Service Based Node) NF Discovery |
|
NF Producer (Additional data fields when Test NRF (Nnrf) and Emulate SMF are enabled) |
NF Producer (Additional data fields when Test NRF (Nnrf) and Emulate UDM are enabled)
|
|
NF Producer (Additional data fields when Test NRF (Nnrf) and Emulate AUSF are enabled) |
NF Producer (Additional data fields when Test NRF (Nnrf) and Emulate PCF are enabled) |
|
NF Producer (Additional data fields when Test NRF (Nnrf) and Emulate UDR are enabled)
|
NF Producer (Additional data fields when Test NRF (Nnrf) and Emulate CHF are enabled) |
|
NF Producer Nbsf - (Additional data fields when Test NRF (Nnrf) and Emulate BSF are enabled) and when BSf (Nbsf) is enabled on Service Based Node test case. NF Consumer PCF-BSF (Additional data fields when Test BSF (Nnrf) and From PCF / From AF are enabled)
PCF-BSF (additional data fields) and AF-BSF PCF-BSF (Update Session Binding Info)
|
SCP, SCP-NF when SCP is enabled on service Based Node
|
|
NF Producer (Additional data fields when Test NRF (Nnrf) and Emulate UPF are enabled) |
NF Consumer (Additional data fields when NEF (Nnef) and To AMF (N51)) are enabled NEF-AMF Tab
|
|
NF Consumer (Additional data fields when NEF (Nnef) and To AMF (N51)) are enabled NEF-AMF Tab on Service Based Node test case
|
NF Consumer (Additional data fields when NEF (Nnef) and To AMF (N51)) are enabled NEF-AMF Tab on Service Based Node test case
|
|
NF Producer (Additional data fields when Test NEF (Nnef) and Emulate AMF (N51) or Test SMSF (Nsmsf) and From AMF (N20)) are enabled Namf Tab Notification Settings |
NF Producer (Additional data fields when Test NEF (Nnef) and Emulate AMF (N51) or Test SMSF (Nsmsf) and From AMF (N20)) are enabled Namf Tab Notification Settings
|
|
NF Consumer NEF-SMF , (Additional data fields for NEF (Nnef) - To SMF (N29)) NEF-SMF Tab |
NF Consumer NEF-SMF , (Additional data fields for NEF (Nnef) - To SMF (N29)) NEF-SMF Tab
Subscribe Events Settings / Updated Events Settings (Pop-up)
|
|
NF Producer (Additional data fields when Test NEF (Nnef) and Emulate SMF (N29)) are enabled Nsmf Tab Notification Settings |
NF Producer (Additional data fields when Test NEF (Nnef) and Emulate SMF (N29)) are enabled Nsmf Tab Notification Settings |
|
NF Producer (Additional data fields when Test NEF (Nnef) and Emulate UDM (N52)) are enabled Nudm Tab Notification Settings |
NF Producer (Additional data fields when Test NEF (Nnef) and Emulate UDM (N52)) are enabled Nudm Tab Notification Settings |
|
NF Consumer (Additional data fields when NEF (Nnef) and To AMF (N52)) are enabled NEF-UDM Tab
Retrieve SMSF Information 3GPP Access Non 3GPP Access
|
NF Consumer (Additional data fields when NEF (Nnef) and To AMF (N52)) are enabled NEF-UDM Tab
Subscribe Events Settings / Updated Events Settings (Pop-up) |
|
NF Producer (Additional data fields when SEPP is enabled on Service Based Node) pSEPP N32-c Tab pSEPP N32-f Tab |
NF Consumer (Additional data fields when Roaming Scenario with SEPP is enabled on Service Based Nodal / Service Based Node) NF-SEPP Tab
SEPP-NF Tab (Additional data fields when Roaming Scenario with SEPP and SEPP are enabled on Service Based Node)
SEPP Tab (Available when SEPP are enabled on Service Based Node) |
NF Producer
|
Namf Version (29.518) |
Select the Namf Version (29.518). Available when Test UDM (Nudm), From AMF (N8) is selected on Service Based Nodal test case and when Test AUSF (Nausf), From AMF (N12) is selected on Service Based Nodal test case and when Test PCF (Npcf), From AMF (N15) is selected on Service Based Nodal test case on Interface Namf. Also available when NEF (Nnef)- To AMF (N51) is enabled on Service Based Node test case on Interface NEF-AMF. Available when LMF (Nlmf) is selected on Service Based Node test case and when PCF (Npcf) and Visiting PCF are selected on Service Based Node test case. Available on AMF Node (When SMF Emulation is not enabled), AMF Nodal with SMF/UPF Node Emulation and SMF Nodal / SMF Node test cases. Available on Service Based Node Emulator Configuration when SMSF (Nsmsf) (N20) and when CBCF (N50) is enabled Available on AMF Node when N12 Interface is enabled. Options: 15.2.0/Dec2018 (default) , 15.4.0/Jun2019, 16.2.0/Dec2019, 16.6.0/Dec2020, 16.7.0/Mar2021 , 17.6.0/Jun2022, 17.10.0/Sep2023
Tcl Parameter: NamfSbiVersion Tcl Parameter: NlsNamfSbiVersion Tcl Parameter: N11NamfSbiVersion Tcl Parameter: N14NamfSbiVersion Tcl Parameter: N15NamfSbiVersion Tcl Parameter: N20NamfSbiVersion Tcl Parameter: N50NamfSbiVersion Tcl Parameter: N51NamfSbiVersion Tcl Parameter: NamfProducerVersion |
|||||||||||||||||||||||||||||
|
Select to enter the API Prefix for amf. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: NamfApiPrefixEn Tcl Parameter: NamfApiPrefix |
||||||||||||||||||||||||||||||
|
Select Validate Access Token to support OAuth2 Authorization for NF Producer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Select to Validate Expiration Time. Configurable only when "Validate Access Token" is enabled.
Tcl Parameter: NamfValidateAccTokEn Tcl Parameter: NamfAccTokSecKey Tcl Parameter: NamfValidateAccTokExpireTimeEn |
||||||||||||||||||||||||||||||
|
Select “Use Access Token” option to support OAuth2 authorization for NF Consumer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Select to enter Access Token. Enter up to 1023 characters. Tcl Parameter: N50NamfUseAccTokEn Tcl Parameter: N50NamfAccTokEn Tcl Parameter: N50NamfAccTok Tcl Parameter: NlsNamfUseAccTokEn Tcl Parameter: NlsNamfAccTokEn Tcl Parameter: NlsNamfAccTok |
||||||||||||||||||||||||||||||
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: NamfDefaultHostFormat |
|||||||||||||||||||||||||||||
|
Enter Supported Features. Unrestricted text field. Default : 1f Tcl Parameter: NamfSuppFeat Tcl Parameter: N50NamfSuppFeat |
||||||||||||||||||||||||||||||
|
Available in AMF Node test case under Namf and AMF-AMF Interface (N14 Interface). Also available in SMF Nodal test case under Namf. Per 6.1.6.2.32 (Type:N1N2MsgTxFrErrDetail) in TS29.518, retryAfter IE will be included when AMF sends N1N2Message Transfer Error in response to N1N2MessageTransferReqData. Range : 1 to 10 (seconds) Default : 1 Tcl Parameter: NamfRetryAfterTimeEn Tcl Parameter: NamfRetryAfterTime Tcl Parameter: N14NamfRetryAfterTimeEn Tcl Parameter: N14NamfRetryAfterTime |
||||||||||||||||||||||||||||||
|
Available on AMF Node test case on Namf NF Producer Tab. Select to support N1N2Transfer Failure Notification during network triggered service request procedure (paging procedure) described in TS23.502(4.2.3.3) & TS29.518 (5.2.2.3.2). Select for AMF to send “N1N2 Message Transfer Failure Notification” to SMF when transferring page to UE was failed. Tcl Parameter: NamfSuptN1N2MsgTxfrFailNotiToSmfEn |
||||||||||||||||||||||||||||||
|
Available on AMF Node test case on Namf NF Producer Tab when N50 Interface is enabled. Enter Maximum Non-UE N2 Subscriptions. Range : 1 to 256 Default : 16 Tcl Parameter: NamfNonUeN2SubCnt |
||||||||||||||||||||||||||||||
| Generate NASC |
Available on AMF Node test case on Namf NF Producer Tab. Enable to generate NASC (NAS Container) for AMF Node/Nodal support to handle NASC in Handover Request. Per TS 33.501 Chapter 6.9.2.3.3 N2-Handover as below: "Upon reception of the NGAP HANDOVER REQUIRED message, the source AMF uses its local policy to determine whether to perform horizontal KAMF derivation on currently active KAMF. If horizontal KAMF derivation is performed, the Namf_Communication_CreateUEContext Request shall contain an indication (i.e., keyAmfHDerivationInd ) that the new KAMF has been calculated, an indication (i.e., keyAmfChangeInd) that AS key re-keying is required at the UE, and the downlink NAS COUNT used in the horizontal derivation of the sent KAMF. The ngKSI for the newly derived KAMF key has the same value and the same type as the ngKSI of the current KAMF. Further, the source AMF shall derive a new KgNB associated with NCC=0 using the newly derived KAMF and the uplink NAS COUNT value of 232-1 as defined in Annex A.9. The source AMF shall include the{NH=newly derived KgNB, NCC=0} pair and the ngKSI for the newly derived KAMF key in the Namf_Communication_CreateUEContext Request as well. If the target AMF receives the indication of horizontal KAMF derivation (i.e., keyAmfHDerivationInd), it shall derive the NAS keys from the received KAMF as specified in clause A.8 and set the NAS COUNTs to zero. The target AMF shall create a NASC (NAS Container) containing the K_AMF_change_flag, the received downlink NAS COUNT, ngKSI, selected NAS security algorithms, and NAS MAC. The K_AMF_change_flag is set to one when the target AMF receives keyAmfHDerivationInd_. Otherwise, the K_AMF_change_flag is set to zero. If the target AMF does not receive keyAmfHDerivationInd but wants to change the NAS algorithms, it shall create a NASC using the selected NAS security algorithms in the same manner as the case for the horizontal KAMF derivation. However, the target AMF shall not set the NAS COUNTs to zero." 3GPP TS 33.501: Security architecture and procedures for 5G system 3GPP TS 24.501: Non-Access-Stratum (NAS) protocol for 5G System 3GPP TS 38.413: NG Application Protocol (NGAP)
Tcl Parameter: NamfNascHoReqEn |
|||||||||||||||||||||||||||||
|
Available on SMF Node test case on SMF-AMF NF Consumer Tab. Select to include “N1N2MessageTransferFailureNotifyURI” in Namf_Communication_N1N2MessageTrasnfer sent by SMF to AMF during network triggered service request procedure (paging producer). This URI will be used when AMF notifies SMF that transferring page to UE was failed. Note: If N1N2MessageTransferFailureNotifyURI in not included in Namf_Communication_N1N2MessageTrasnfer from SMF, AMF won’t send “N1N2 Message Transfer Failure Notification” to SMF even if this option is enabled. Tcl Parameter: N11NamfN1N2MsgTxfrFailNotiUriEn |
||||||||||||||||||||||||||||||
| NGAP Version (38.413) |
Available when LMF (Nlmf) is selected on Service Based Node test case on the LMF-AMF tab. Select the NGAP Version (38.413) Options: 15.0.0/Jun2018, 15.1.0/Sep2018, 15.2.0/Jan2019 , 15.2.0-Variant1/Jan2019 , 15.2.0-Variant2/Mar2019 , 15.4.0/Jul2019, 16.2.0/July2020, 17.6.0/Sep2023 (default) Tcl Parameter: NlsNamfNgapVersion |
|||||||||||||||||||||||||||||
| N1N2 Message Subscribe |
Available when LMF (Nlmf) is selected on Service Based Node test case on the LMF-AMF tab. The N1N2MessageSubscribe service operation is used by a NF Service Consumer (e.g. LMF or PCF) to subscribe to the AMF for notifying N1 messages of a specific type (e.g. LPP). Reference : 5.2.2.3.3 N1N2MessageSubscribe 29.518. Tcl Parameter: NlsNamfN1N2MsgSubscribeEn |
|||||||||||||||||||||||||||||
| Non UE N2 Message Subscribe |
Available when LMF (Nlmf) is selected on Service Based Node test case on the LMF-AMF tab. The NonUeN2InfoSubscribe service operation is used by a NF Service Consumer (e.g. LMF, CBCF or PWS-IWF) to subscribe to the AMF for notifying non UE specific N2 information of a specific type (e.g. NRPPa or PWS Indications). Reference : 5.2.2.4.2 NonUeN2InfoSubscribe 29.518. Tcl Parameter: NlsNamfNonUeN2MsgSubscribeEn |
|||||||||||||||||||||||||||||
|
Retry Count |
Available on the PCF-AMF Tab for Service Based Node test case when Namf Version >= 17.6.0/Jun2022. Limitation /Caveat : Because the PCF may split the URSP from the UDR into several N1N2 message transfers based on specification in 23.502, the T3501 timer shall be started when it sends the N1N2 message transfer to AMF. Thus, the messages 5 to 7 in the call flow below shall not be set in the message flow if the message flow is enabled in PCF node. After all the URSPs are delivered successfully, the PCF will send message 7. The Ue Policy max size in PCF node is 1200 bytes. Based on 23.502 4.15.6.10 "Application guidance for URSP determination", PCF is required to support Npcf_EventExposure_Notify. The entire scenario, involving AMF Node, PCF Node, UDM Node, UDR Node and NEF Node, is shown here:
Enter the T3501 Timer value in milliseconds. Range : 50 to 5000 , default : 100 Enter the Retry Count. Range: 1 to 3, default : 1 Tcl Parameter: N15NamfT3501ToValue Tcl Parameter: N15NamfT3501RetrCnt |
|||||||||||||||||||||||||||||
| NGAP Version (38.413) |
Select the NGAP Version. Available when Test CBCF , Emulate AMF (N50) is selected on Service Based Nodal test case. Options : 15.4.0/Jul2019 ,16.2.0/Jul2020 Tcl Parameter: NamfNgapVersion |
|||||||||||||||||||||||||||||
| PWS |
Select Restart/Failure Indication. Available when Test CBCF , Emulate AMF (N50) is selected on Service Based Nodal test case.
Tcl Parameter: NamfPwsRestartFailureIndEn Restart / Failure Indication
|
|||||||||||||||||||||||||||||
|
Nsmf Version (29.502/29.508) - Service Based test cases Nsmf Version (29.502) - SMF test cases |
Select the Nsmf Version. Available when Test UDM (Nudm), From SMF (N10) is selected on Service Based Nodal test case and when Test PCF (Npcf), From SMF (N7) is selected on Service Based Nodal test case on Interface Nsmf. Also available when NEF (Nnef)- To SMF (N29) is enabled on Service Based Node test case on Interface NEF-SMF. Available when SMF is selected on Service Based Node Emulator Configuration . Also available on SMF Nodal (NF Consumer) and SMF Node (NF Producer) test cases. 29.502 is the Spec ID for SMF test cases. Available on AMF Node and AMF Nodal with SMF/UPF Node Emulation. Options: 15.2.0/Dec2018 , 15.2.1/Dec2018 ,15.4.0/Jun2019 (default for AMF Node , SMF Nodal / Node) , 16.2.0/Dec2019, 16.6.0/Dec2020, 17.10.0/Sep2023 Tcl Parameter: NsmfSbiVersion Tcl Parameter: N29NsmfSbiVersion Tcl Parameter: N11NsmfSbiVersion |
|||||||||||||||||||||||||||||
|
Select to enter the API Prefix for smf. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: NsmfApiPrefixEn Tcl Parameter: NsmfApiPrefix |
||||||||||||||||||||||||||||||
|
Select Validate Access Token to support OAuth2 Authorization for NF Producer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Select to Validate Expiration Time. Configurable only when "Validate Access Token" is enabled.
Tcl Parameter: NsmfValidateAccTokEn Tcl Parameter: NsmfAccTokSecKey Tcl Parameter: NsmfValidateAccTokExpireTimeEn |
||||||||||||||||||||||||||||||
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: NsmfDefaultHostFormat |
|||||||||||||||||||||||||||||
| GTPv2 Version |
Select the GTPv2 Version. Available on SMF Node Nsmf interface when Support Interworking with EPS for N16 interface is enabled. Options : 15.2.0 Tcl Parameter: NsmfGtp2Version |
|||||||||||||||||||||||||||||
|
Select to add the instance number of sm-context to smContextRef (<supi>-<pdu-session-id>) in location header of CreateSMContext Response sent by SMF(Nsmf Producer). Available on the Nsmf tab tab on the SMF Node test case. For example, when supi : imsi-123456789000001, pdu-session-id : 5, instance # of sm context:101 If enabled, smContextRef will be “imsi-123456789000001-5-ins:101”. Otherwise, smContextRef will be “imsi-123456789000001-5” Tcl Parameter: NsmfSmCntxRefWithInsNumEn |
||||||||||||||||||||||||||||||
| Propriety SmContextRef Format |
Select to use the proprietary smContextRef format instead of Landslide own format. When this option is enabled, “SmContextRef with Instance Number” option is disabled. Tcl Parameter: NsmfPtySmCntxRefFmtEn Tcl Parameter: NsmfPtySmCntxRefFmt |
|||||||||||||||||||||||||||||
|
Select to change the authority of the created resource URI apiRoot sent to AMF during Create SM Context Service Operation. If this option is enabled, the # of Nodes in SMF SBI Node will be enforced to 2. The first SMF SBI Node will act as the delegate Http2 Server. The Authority of the created resource URI apiRoot sent to AMF during the Create SM Context Service operation will be set in the second SMF SBI Node. SMF(Nsmf Producer). Available on the Nsmf tab o the SMF Node test case. Tcl Parameter: NsmfChgAuthorityInCreatedRsrcUriEn |
||||||||||||||||||||||||||||||
|
Disable SmContextStatusNotify by Collision During CreateSmContext service Operation |
Available Available on the Nsmf Interface on the SMF Node test case. Select to disable the condition to send SmContextStatusNotify (ResourceStatus: RELEASED) to AMF when the new POST request collides with the existing SmContext during Create Sm Context Service Operation. Tcl Parameter: NsmfDisableSmCtxStsNotiByCollisionEn |
|||||||||||||||||||||||||||||
|
MCC , MNC |
Select Allowed PLMNs and enter the Number of PLMNs (Up to 16). Available on the Nsmf Interface on the SMF Node test case. MCC and MNC are available on AMF Node test case under Nsmf tab. Tcl Parameter: NsmfMcc Tcl Parameter: NsmfMnc Tcl Parameter: NsmfAllowedPlmnsEn Tcl Parameter: NsmfAllowedPlmnsNum Enter the Mobile Country Code for each PLMN. Range: 3 digits Default: 000 Tcl Parameter: NsmfAllowedMcc_1 Enter the Mobile Network Code for each PLMN. Range: 2 to 3 digits Default: 00 Tcl Parameter: NsmfAllowedMnc_1 |
|||||||||||||||||||||||||||||
|
Available on the Nsmf Interface on the SMF Node test case Select to enter the Number of NSI IDs - up to 4. Enter NSI ID (Network Slice Information identifier). Range : 1 to 255 characters Tcl Parameter: NsmfNsiIdsEn Tcl Parameter: NsmfNumNsiIds Tcl Parameter: NsmfNsiId_1 |
||||||||||||||||||||||||||||||
|
See additional details below S-NSSAI Info. |
||||||||||||||||||||||||||||||
|
Select the Nausf Version. Available when Test UDM (Nudm), From AUSF (N13) is selected on Service Based Nodal test case on Interface Nausf. Available when AUSF (Nausf) is selected on Service Based Node test case on Interface Nausf. Options: 15.2.0/Dec2018 (default) , 15.4.0/Jun2019, 16.6.0/Dec2020 Tcl Parameter: NausfSbiVersion |
||||||||||||||||||||||||||||||
|
Select to enter the API Prefix for ausf. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: NausfApiPrefixEn Tcl Parameter: NausfApiPrefix |
||||||||||||||||||||||||||||||
|
Select Validate Access Token to support OAuth2 Authorization for NF Producer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Select to Validate Expiration Time. Configurable only when "Validate Access Token" is enabled.
Tcl Parameter: NausfValidateAccTokEn Tcl Parameter: NausfAccTokSecKey Tcl Parameter: NausfValidateAccTokExpireTimeEn |
||||||||||||||||||||||||||||||
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: NausfDefaultHostFormat |
|||||||||||||||||||||||||||||
| Default Binding Level |
Enable to select the default binding level. Available when NRF Interface is enabled on the Service Based Node test case. Options : NF Set, NF Instance (default) NF Set can be selected only when NF Set ID is configured in AUSF SBI Node under Network Devices. Tcl Parameter: NausfDefBindLevelEn Tcl Parameter: NausfDefBindLevel |
|||||||||||||||||||||||||||||
|
Select which authentication Algorithm to use. Available in Service Based Nodal when Test AUSF (Nausf), From AMF (N12) is selected and on Service Based Node when AUSF (Nausf) is selected. You can only select one or the other, or both (5G AKA, EAP) in Service Based Nodal. You can only select one or the other, not both (5G AKA, EAP) in Service Based Node. 5G AKA or EAP are supported. If 5G AKA is selected, the 5G AKA Pane becomes available for input. If EAP is selected, the EAP Settings box becomes available to select. Currently only EAP-AKA' is supported. Tcl Parameter: Nausf5gAkaEn Tcl Parameter: N12Nausf5gAkaEn |
||||||||||||||||||||||||||||||
|
Algorithm |
Select an Authentication Algorithm for 5G AKA. Additional fields become available for input. Options : Milenage ( Defined in 3GPP TS 35.205) , Test Algorithm ( Defined in 3GPP TS 34.108), TUAK (3GPP TS 35.231) Available in Service Based Nodal when Test AUSF (Nausf), From AMF (N12) is selected and on Service Based Node when AUSF (Nausf) is selected. Tcl Parameter: Nausf5gAkaAlg Tcl Parameter: N12Nausf5gAkaAlg |
|||||||||||||||||||||||||||||
| Secret Key |
The MS's text or hexadecimal key that is associated with its GUTI and is used to derive the MME/LTE ciphering key. Available in Service Based Nodal when Test AUSF (Nausf), From AMF (N12) is selected and on Service Based Node when AUSF (Nausf) is selected. Range: Either String or HEX, If hex must start with 0x Default: 0x00
Tcl Parameter: NausfSecretKey Tcl Parameter: N12NausfSecretKey |
|||||||||||||||||||||||||||||
| RES Length (bytes) |
Per 3GPP (33.102) specified RES Length of 4-16 octets. Per 34.108, for support of 128 bits (16 bytes). Available in Service Based Nodal when Test AUSF (Nausf), From AMF (N12) is selected and on Service Based Node when AUSF (Nausf) is selected. Range: 4, 8, 16 Default : 8 Tcl Parameter: NausfAuthResLen Tcl Parameter: N12NausfAuthResLen |
|||||||||||||||||||||||||||||
| Operator Variant |
The 128-bit, operator-specific MILENAGE constant (OP) provisioned for the network. Range: Up to 16-Byte hex string Available in Service Based Nodal when Test AUSF (Nausf), From AMF (N12) is selected and on Service Based Node when AUSF (Nausf) is selected. Default: 0x63BFA50EE6523365FF14C1F45F88737D Tcl Parameter: NausfOpType Tcl Parameter: NausfOpVar Tcl Parameter: N12NausfOpType Tcl Parameter: N12NausfOpVar |
|||||||||||||||||||||||||||||
| OPc |
A128-bit value derived from OP and K and used in subsequent computations. Hence, less sensitive and if obtained by third party. Available in Service Based Nodal when Test AUSF (Nausf), From AMF (N12) is selected and on Service Based Node when AUSF (Nausf) is selected.
Range: Up to 16-Byte hex string Default: 0x63BFA50EE6523365FF14C1F45F88737D Tcl Parameter: NausfOpC Tcl Parameter: N12NausfOpC |
|||||||||||||||||||||||||||||
| TUAK Algorithm |
The following fields become available when Algorithm = TUAK. For information about how the fields are used in the TUAK algorithm the user should refer to the 3GPP TS 35.231 specification. Available in Service Based Nodal when Test AUSF (Nausf), From AMF (N12) is selected and on Service Based Node when AUSF (Nausf) is selected.
|
|||||||||||||||||||||||||||||
| AMF |
Enter up to a 2 byte hex string for the AMF. Available in Service Based Nodal when Test AUSF (Nausf), From AMF (N12) is selected and on Service Based Node when AUSF (Nausf) is selected Range: 2-Byte hex string Default: 0x8000 Tcl Parameter: NausfAmf Tcl Parameter: NausfTuakAmf Tcl Parameter: N12NausfAmf Tcl Parameter: N12NausfTuakAmf |
|||||||||||||||||||||||||||||
| Fixed Network Residential Gateway Authenticated Indication |
Available when Nausf Version > = 16.6.0/Dec2020. Available on :
Select for indicate support of FN-RG Authentication Procedure per 3GPP TS 33.501 7B.3 Authentication for FN-RG. Options : false (authenticated by W-AGF) , true (authenticated by W-AGF) Authenticated Indication IE is supported in Nausf_UEAuthentication_Authenticate (rg-authentications) Request / Response and Nudm_UEAuthentication_Get (security-information-rg) Request / Response message. For AUSF, commands AUSF_RG_AUTH_REQ and AUSF_RG_AUTH_RESP address Nausf_UEAuthentication_Authenticate (rg-authentications) operation. For UDM, commands UEAU_Get_Rg_Auth_Data and UEAU_Get_Rg_Auth_Data_Resp address Nudm_UEAuthentication_Get (security-information-rg) operation. The call scenario related with this feature is liking as below (from TS 33.501):
Tcl Parameter: NausfFnrgAuthIndEn Tcl Parameter: NausfFnrgAuthInd Tcl Parameter: N12NausfRgAuthIndEn Tcl Parameter: N12NausfRgAuthInd Tcl Parameter: N13NudmRgAuthIndEn Tcl Parameter: N13NudmRgAuthInd |
|||||||||||||||||||||||||||||
| Authentication Result |
Available on Nausf tab when Service Based Node when AUSF (Nausf) or (AUSF (Nausf) and To UDM (N13) ) is selected and when Nausf Version > = 16.6.0/Dec2020. Additional details in Fixed Network Residential Gateway Authentication Indication . Select the Authentication Result. Options : AUTHENTICATION_SUCCESS , AUTHENTICATION_FAILURE , AUTHENTICATION_ONGOING Tcl Parameter: NausfFnrgAuthResult |
|||||||||||||||||||||||||||||
|
Select the Nudm Version. Available when Test AUSF (Nausf), Emulate UDM (N13) and when Test NEF (Nnef), Emulate UDM (N52), is selected on Service Based Nodal test case on Interface Nudm. Also available when UDM (N8) is enabled on SMF Nodal test case. Options: 15.2.0/Dec2018 , 15.2.1/Dec2018 (SMF Nodal) , 15.4.0/Jun2019, 16.2.0/Dec2019, 16.6.0/Dec2020, 16.7.0/Mar2021 Tcl Parameter: NudmSbiVersion Tcl Parameter: N52NudmSbiVersion |
||||||||||||||||||||||||||||||
|
Select to enter the API Prefix for udm. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: NudmApiPrefixEn Tcl Parameter: NudmApiPrefix |
||||||||||||||||||||||||||||||
|
Available when NRF (Nnrf) is selected on Service Based Node test case on Interface Nnrf. Options: 15.2.0/Dec2018 (default) , 15.4.0/Jun2019, 16.6.0/Dec2020 Tcl Parameter: NnrfSbiVersion |
||||||||||||||||||||||||||||||
|
Select Access Token Service to enter a Secret Key. Available when NRF (Nnrf) is selected on Service Based Node test case on Interface Nnrf. Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Tcl Parameter: NnrfAcTokenSrvEn Tcl Parameter: NnrfSecretKey |
||||||||||||||||||||||||||||||
|
Select to enter the API Prefix for nrf. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: NnrfApiPrefixEn Tcl Parameter: NnrfApiPrefix |
||||||||||||||||||||||||||||||
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: NnrfDefaultHostFormat |
|||||||||||||||||||||||||||||
|
Select to Use TLS Private Key. To support OAuth token based on X.509v3 certificate (RFC7519 and RFC7515) Available when NRF (Nnrf) is selected on Service Based Node test case on Interface Nnrf , Enable TLS is enabled on Http2 tab and when Access Token Service is enabled. It's mutually exclusive with Secret Key. Select the Algorithm. Options : RS256 (default) , RS384, RS512 , ES256 , ES384 , ES512 , PS256, PS384, PS512 Tcl Parameter: NnrfSigWithPriKeyEn Tcl Parameter: NnrfSigAlgo |
||||||||||||||||||||||||||||||
|
Enable Access Token Expiration Time
Expiration Time Relative Expiration Time |
Select to enable Access Token expiration time verification. Available when Access Token Service is enabled. Enter Expiration Time per RFC3339 Format or Relative Expiration Time in seconds - range 10 - 999999, default : 10. Tcl Parameter: NnrfAcTokenExpireTimeEn Tcl Parameter: NnrfTokenExpireTime Tcl Parameter: NnrfTokenExpireRelativeTime |
|||||||||||||||||||||||||||||
|
Available when LMF (Nlmf) is selected on Service Based Node test case on Interface Nlmf. Available when NLs Interface is selected on AMF Node test case on Interface AMF-LMF. Options: 15.2.0/Dec2018 (default for Service Based test case) , 15.4.0/Jun2019 (default for AMF Node test case) Tcl Parameter: NlsNlmfSbiVersion Tcl Parameter: NlmfSbiVersion |
||||||||||||||||||||||||||||||
|
Select to enter the API Prefix for lmf. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: NlmrfApiPrefixEn Tcl Parameter: NlmrfApiPrefix |
||||||||||||||||||||||||||||||
|
Select Validate Access Token to support OAuth2 Authorization for NF Producer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Select to Validate Expiration Time. Configurable only when "Validate Access Token" is enabled.
Tcl Parameter: NlmfValidateAccTokEn Tcl Parameter: NlmfAccTokSecKey Tcl Parameter: NlmfValidateAccTokExpireTimeEn |
||||||||||||||||||||||||||||||
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: NlmfDefaultHostFormat |
|||||||||||||||||||||||||||||
|
Available when ( Test BSF (Nbsf), From AF or Test NEF (Nnef), From AF (N33)) or when (Test PCF (Npcf), From SMF (N7), From AF (N5)) is enabled on Service Based Nodal test case on Interface Naf. Options: 15.4.0/Jun2019, 16.7.0/Mar2021 Tcl Parameter: NafSbiVersion |
||||||||||||||||||||||||||||||
|
Select to enter the API Prefix for lmf. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: NafApiPrefixEn Tcl Parameter: NafApiPrefix |
||||||||||||||||||||||||||||||
|
Select Validate Access Token to support OAuth2 Authorization for NF Producer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Select to Validate Expiration Time. Configurable only when "Validate Access Token" is enabled. Tcl Parameter: NafValidateAccTokEn Tcl Parameter: NafAccTokSecKey Tcl Parameter: NafValidateAccTokExpireTimeEn |
||||||||||||||||||||||||||||||
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: NafDefaultHostFormat |
|||||||||||||||||||||||||||||
|
Available when Test NRF (Nnrf), Emulate SMSF is selected on Service Based Nodal test case on Interface Nsmsf. And on Service Based Node Emulator Configuration when SMSF (Nsmsf) is enabled. Available when Test SMSF (Nsmsf), From AMF (N20) is selected on Service Based Nodal test case on Interface AMF-SMSF. Options: 15.4.0/Jun2019 Tcl Parameter: NsmsfSbiVersion Tcl Parameter: N20NsmsfSbiVersion |
||||||||||||||||||||||||||||||
|
Select to enter the API Prefix for smsf. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: NsmsfApiPrefixEn Tcl Parameter: NsmsfApiPrefix |
||||||||||||||||||||||||||||||
|
Select Validate Access Token to support OAuth2 Authorization for NF Producer. Select to enter the API Prefix for smsf for N20 interface. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Select to Validate Expiration Time. Configurable only when "Validate Access Token" is enabled. Tcl Parameter: NsmsfValidateAccTokEn Tcl Parameter: NsmsfAccTokSecKey Tcl Parameter: NsmsfValidateAccTokExpireTimeEn Tcl Parameter: N20NsmsfApiPrefixEn Tcl Parameter: N20NsmsfApiPrefix |
||||||||||||||||||||||||||||||
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: NsmsfDefaultHostFormat |
|||||||||||||||||||||||||||||
|
Available when GMLC (Ngmlc) is selected on Service Based Node test case on Interface Ngmlc. Available when NLg Interface is selected on AMF Node test case on Interface AMF-GMLC. Options: 15.2.0/Dec2018 (default for AMF Node test case) Options: 15.4.0/Jun2019 (default for Service Based Node test case) Tcl Parameter: NlgNgmlcSbiVersion Tcl Parameter: NgmlcSbiVersion |
||||||||||||||||||||||||||||||
|
Select to enter the API Prefix for gmlc. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: NgmlcApiPrefixEn Tcl Parameter: NgmlcApiPrefix |
||||||||||||||||||||||||||||||
|
Select Validate Access Token to support OAuth2 Authorization for NF Producer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Select to Validate Expiration Time. Configurable only when "Validate Access Token" is enabled. Tcl Parameter: NgmlcValidateAccTokEn Tcl Parameter: NgmlcAccTokSecKey Tcl Parameter: NgmlcValidateAccTokExpireTimeEn |
||||||||||||||||||||||||||||||
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: NgmlcDefaultHostFormat |
|||||||||||||||||||||||||||||
|
Available when NLg Interface is selected on AMF Node test case on Interface AMF-GMLC. Enter the Location Notification URI. Up to 256 characters. Default: /ntf-service/v1/namf-notify/loc-eventnotify Tcl Parameter: NlgNgmlcLocNtfUri |
||||||||||||||||||||||||||||||
| Neir Version (29.511) |
Available when 5G-EIR (N5g-eir) is selected on Service Based Node test case on Interface Neir. Options: 15.4.0/Jun2019 Tcl Parameter: NeirSbiVersion |
|||||||||||||||||||||||||||||
| API Prefix |
Select to enter the API Prefix for Neir. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: NeirApiPrefixEn Tcl Parameter: NeirApiPrefix |
|||||||||||||||||||||||||||||
| Validate Access Token |
Select Validate Access Token to support OAuth2 Authorization for NF Producer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Select to Validate Expiration Time. Configurable only when "Validate Access Token" is enabled. Tcl Parameter: NeirValidateAccTokEn Tcl Parameter: NeirAccTokSecKey Tcl Parameter: NeirValidateAccTokExpireTimeEn |
|||||||||||||||||||||||||||||
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: NeirDefaultHostFormat |
|||||||||||||||||||||||||||||
| Equipment Status |
Available when 5G-EIR (N5g-eir) is selected on Service Based Node test case on Interface Neir. Select Group Number. Options: 0 to 16 Enter Starting UE Index, Ending UE Index, Equipment Status for each Group Number selected. Starting UE Index must less than Ending UE Index,Both Starting UE Index and Ending UE Index must less than number of subscribers. Equipment Status options : WHITELISTED (default), BLACKLISTED, GREYLISTED Tcl Parameter: NeirGroupNum Tcl Parameter: NeirGroupId_1 |
|||||||||||||||||||||||||||||
| Nnwdaf Version (29.520) |
Available when NWDAF (Nnwdaf) is selected on Service Based Node test case on Interface Nnwdaf. Options: 16.6.0/Dec2020 Tcl Parameter: NnwdafSbiVersion |
|||||||||||||||||||||||||||||
| API Prefix |
Select to enter the API Prefix for Nnwdaf. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: NnwdafApiPrefixEn Tcl Parameter: NnwdafApiPrefix |
|||||||||||||||||||||||||||||
| Validate Access Token |
Select Validate Access Token to support OAuth2 Authorization for NF Producer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Select to Validate Expiration Time. Configurable only when "Validate Access Token" is enabled. Tcl Parameter: NnwdafValidateAccTokEn Tcl Parameter: NnwdafAccTokSecKey Tcl Parameter: NnwdafValidateAccTokExpireTimeEn |
|||||||||||||||||||||||||||||
|
Supported Features |
Select Events Subscription to enter Supported Features for Nnwdaf (Network Data Analytics Function (NWDAF). Enter Supported Features. Range : up to 8 characters Default : 1ff Tcl Parameter: NnwdafEvtsSuppFeat |
|||||||||||||||||||||||||||||
|
Supported Features |
Select Analytics Information to enter Supported Features for Nnwdaf (Network Data Analytics Function (NWDAF). Enter Supported Features. Range : up to 8 characters Default : 1ff Tcl Parameter: NnwdafAnaSuppFeat |
|||||||||||||||||||||||||||||
|
Nnef Version (29.508/29.518/29.519/29.511/29.122/29.541/29.542) |
Available when NEF (Nnef) is selected on Service Based Node test case and when (Test UDR (Nudr), From NEF (N37)) or (Test NEF (Nnef), Emulate SMF (N29)) on Service Based Nodal test case on Interface Nnef/SMF-NEF. Options: 15.4.0/Jun2019 (default), 16.2.0/Dec2019, 16.6.0/Dec2020, 16.7.0/Sept2020 Tcl Parameter: NnefSbiVersion Tcl Parameter: N29NnefSbiVersion |
|||||||||||||||||||||||||||||
|
Select to enter the API Prefix for nnef. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: NnefApiPrefixEn Tcl Parameter: NnefApiPrefix |
||||||||||||||||||||||||||||||
|
Select Validate Access Token to support OAuth2 Authorization for NF Producer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Select to Validate Expiration Time. Configurable only when "Validate Access Token" is enabled. Tcl Parameter: NnefValidateAccTokEn Tcl Parameter: NnefAccTokSecKey Tcl Parameter: NnefValidateAccTokExpireTimeEn |
||||||||||||||||||||||||||||||
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: NnefDefaultHostFormat |
|||||||||||||||||||||||||||||
| Enable NEF Interworking |
Select to enable NEF Interworking. Available on Nnef tab for Service Based Bode when NEF (Nnef) is enabled. Tcl Parameter: NnefNefInterWorkingEn |
|||||||||||||||||||||||||||||
|
Enter a heartbeat timer interval in seconds. Available when NRF (Nnrf) is selected on Service Based Node test case on Interface Nnrf. Range : 30 to 65535 Default : 60 Tcl Parameter: NnrfHeartbeatTime |
||||||||||||||||||||||||||||||
|
Enter the maximum number of NF instances to return Discover Request. Available when NRF (Nnrf) is selected on Service Based Node test case on Interface Nnrf. Range : 10 to 2500 Default : 10 Tcl Parameter: NnrfRetNfInstMaxNum |
||||||||||||||||||||||||||||||
| Return NF Profile After Status Subscription |
Select to for the NRF will return all matched AMF after a new NF Status is received. The NRF will return NF_REGISGTER event if the AMF registers to NRF again without the deregister message sent to NRF in last stop. The NRF does not support notifying SCP of all NFs profiles. Select specific NFs via the reqNfType / reqNfFqdn attributes. Available when NRF (Nnrf) is selected on Service Based Node test case on Interface Nnrf. Range : 10 to 50 Default : 10 Tcl Parameter: NnrfReturnProfileAfterSubsEn |
|||||||||||||||||||||||||||||
|
Also available on SMF Nodal (NF Consumer). Select to support a vendor's format of smContextStatusUri. Options: Variant1 Tcl Parameter: N11NsmfPropSmCntxStsUriEn Tcl Parameter: N11NsmfPropSmCntxStsUri |
||||||||||||||||||||||||||||||
| Include Proprietary Custom Header x-lb-hash-key |
Also available on SMF Nodal and on AMF Node - without SMF emulation (NF Consumer) on the AMF-SMF Tab. Select to include the proprietary custom header “x-lb-hash-key” in http2 message over N11 (SM Context Message) to SMF. If it is enabled, “x-lb-hash-key: imsi-310401234567890” will be added to http2 request message toward SMF over N11. Options: Variant1 Tcl Parameter: N11NsmfPtyCustHdrXLbHashKeyEn |
|||||||||||||||||||||||||||||
| Origination Timestamp |
Select to include the Custom Http headers for Origination Timestamp (3gpp-Sbi-Origination-Timestamp). 3gpp-Sbi-Origination-Timestamp: contains the date and time (with a millisecond granularity) when the originating entity initiated the response. Enter Max Response Time (ms) in Milliseconds. Range : 1 to 60000 Default : 1 Nsmf_PDUSession_CreateSMContext/UpdateSMContext/ReleaseSMContext/Retrieve Response generated via the N11 (AMF-SMF) interface on SMF Node test case will include these fields in the header. Available when Nsmf Version is > = 16.6.0. in AMF Node, SMF Nodal/Node. Tcl Parameter: Nsmf3gppSbiOrigTimestampEn Tcl Parameter: Nsmf3gppSbiOrigMaxRspTimestamp Tcl Parameter: N11Nsmf3gppSbiOrigTimestampEn Tcl Parameter: N11Nsmf3gppSbiOrigMaxRspTimestamp |
|||||||||||||||||||||||||||||
|
H-SMF Info H-SMF URI ApiRoot H-SMF NF Instance ID H-SMF Host FQDN Preferred |
Available on the AMF Node test case AMF-SMF Tab when Support Roaming is enabled. Indicate H-SMF information (hSmfUri/hSmfId) that AMF uses for the Home SMF in the home-routed roaming scenario. As of now, AMF doesn’t support H-SMF selection via NRF discovery. Currently, the locally preconfigured H-SMF information is used. Only one H-SMF will be allowed. Note) If the NSSAI of PDU Session Establishment Request sent by UE includes the mapped Home S-NSSAI and it is one of S-NSSAI(s) in the Allowed NSSAI in RegistrationAccept sent by AMF, it will be considered as "PDU session establishment of this PDU will require the home-routed roaming procedure and it will be routed to the configured H-SMF Info". H-SMF URI ApiRoot - Enter the ApiRoot of hSmfUri including SmContextCreateData sent by AMF to vSMF in HR roaming scenario. Range : String with up to 256 characters long For example, if it is configured with “http://10.100.2.51:80”, hSmfUri of SmContextCreateData sent by AMF to vSMF will be constructed as follows: hSmfUri: “http://10.100.2.51:80/nsmf-pdusession/v1/pdu-sessions”, (Where, “/nsmf-pdusession/v1/pdu-sessions” is “/<apiName>/{apiVersion}/<apiSpecificResourceUriPart>” defined in TS29.502 clause 6.1.1 API URI.) H-SMF NF Instance Id - If H-SMF NF Instance Id is selected, enter the NF Instance ID of H-SMF. Format: UUID version 4: 4hexOctet-2hexOctet-2hexOctet-2hexOctet-6hexOctet H-SMF Host FQDN Preferred - Select whether to include H-SMF's FQDN in the ApiRoot of H-SMF URI instead of IP address if both of FQDN and IP Address of H-SMF are available from H-SMF Discovery via NRF. When this option is not enabled, IP Address of H-SMF will be included if it is available. When it is enabled, if FQDN is not available from H-SMF Discovery via NRF, ApiRoot will include IP address of H-SMF. Available on the AMF Node test case AMF-SMF Tab when Support Roaming and NRF Interface is enabled. When enabled, "H-SMF URI ApiRoot" and "H-SMF NF Instance ID" are both disabled. NF Discovery Query H-SMF Tab becomes available for H-SMF Discovery on interface Nnrf Client. If SMF discovery via NRF is required During PDU Session Establishment procedure or EPS to 5GS Handover procedure, vAMF should proceed H-SMF discovery and V-SMF discovery and then it should send Nsmf_PduSession_CreateSMContext_Request with H-SMF URI information to vSMF. Landslide V-AMF will proceed according to the following message flow.
Tcl Parameter: N11NsmfHsmfUriApiRoot Tcl Parameter: N11NsmfHsmfNfId Tcl Parameter: N11NsmfHsmfHostFqdnPreferredEn |
|||||||||||||||||||||||||||||
|
Activation/Deactivation Retry Timer (s) Max Retries |
Select for retry functionality for the User plane activation and deactivation request. This is done by resending the PDU session update context request message to the SMF over the SBI layer. After maximum retries, a internal notification is sent to NAS 5G about the failure. If DMF has to send the data again via IpInstance, UE will trigger Activation (Service Request procedure) again since it is already in idle mode. The NSMF_PduSession_upgradeSMcontext_req message is resent according to the timer value/max retries that is set on the GUI. If there is no response after Max Retries, UE stays in idle state and N11 Nsmf consumer stays ins EST state. If there is pending data via IpInstance UE will trigger the activation again. Available on SMF Nodal - AMF-SMF (NF Comsumer tab). Per spec 3GPP TS 23.502. Select Activation/Deactivation Retry Timer (s) and enter number of seconds for retry. Range : 1 to 255 Default : 15 Enter Max Retries attempts. Range : 1 to 255, Default : 4 Tcl Parameter: N11NsmfActDeactRetryEn Tcl Parameter: N11NsmfActDeactRetryTime Tcl Parameter: N11NsmfActDeactMaxRetries |
|||||||||||||||||||||||||||||
|
Enter the starting SUPI (Subscription Permanent Identifier). Corresponds to IMSI in earlier generations of networks. Range: 15 digits Tcl Parameter: NamfProducerUeSupi |
||||||||||||||||||||||||||||||
|
Select nrLocation to include the Tracking Area Code and NR Cell ID. The "User Location Information" panel on SMF Nodal's Namf tab has been removed in Release 19.4. The "Tracking Area Code" and "NR Cell ID" values have been moved to the Network Devices/gNB User Node tab and received a Tcl variable name change. Enter Tracking Area Code. Range: 0 to 16777215 Default : 0 Enter NR Cell ID. Range: 0 to 68719476735 Default : 0 Tcl Parameter: NamfInclNrLoc Tcl Parameter: NamfTAC Tcl Parameter: NamfNrCellId |
||||||||||||||||||||||||||||||
|
Available when Test AUSF (Nausf), Emulate UDM (N13) is selected on Service Based Nodal test case on Interface Nudm. Additional details on Nudm Tab - Authentication. |
to use the 
for Pop-up to enter :
Subscription Concealed Identifier
Allows you to configure the SUPI (Subscription Permanent Identifier)
| Use SUCI |
Select to use SUCI de-concealment. UDM performs de-concealment to retrieve SUPI from SUCI, if SUCI is included in the request. Note: SUPI de-concealment from SUCI is described in flow below. Available in Service Based Nodal when (Test AUSF (Nausf), From AMF (N12), or Test UDM(Nudm), From AUSF (N13)) is selected and on Service Based Node when AUSF (Nausf) is selected.
Tcl Parameter: NausfSuciEn Tcl Parameter: N12NausfSuciEn Tcl Parameter: N13NudmSuciEn |
|
Select the Protection Scheme. Available in Service Based Nodal when (Test AUSF (Nausf), From AMF (N12), or Test UDM(Nudm), From AUSF (N13)) is selected and on Service Based Node when AUSF (Nausf) is selected. Option: Null-Scheme, Profile <A>, Profile <B> Tcl Parameter: NausfProtectionScheme Tcl Parameter: N12NausfProtectionScheme Tcl Parameter: N13NudmProtectionScheme |
|
| MSIN ASCII Encoding |
Select for MSIN ASCII encoding. Available when Protection Scheme = Profile <A> or Profile <B>. Available in Service Based Nodal when (Test AUSF (Nausf), From AMF (N12), or Test UDM(Nudm), From AUSF (N13)) is selected and on Service Based Node when AUSF (Nausf) is selected. Range: 0 to 255 Default: 0 Tcl Parameter: NausfMsinAsciiEn Tcl Parameter: N12NausfMsinAsciiEn Tcl Parameter: N13NudmMsinAsciiEn |
|
Enter the Home Network Public Key Id. Available when Protection Scheme = Profile <A> or Profile <B>. Available in Service Based Nodal when (Test AUSF (Nausf), From AMF (N12), or Test UDM(Nudm), From AUSF (N13)) is selected. Range: 0 to 255 Default: 0 Tcl Parameter: N12NausfKhnPubKeyId Tcl Parameter: N13NudmKhnPubKeyId |
|
|
Available when Protection Scheme = Profile <A> or Profile <B>. Available in Service Based Nodal when (Test AUSF (Nausf), From AMF (N12), or Test UDM(Nudm), From AUSF (N13)) is selected. How to generate Home Network Key pair: SSH to the Landslide test server or connect to any system that can execute the commands listed below: For Profile <A>:
For Profile <B> :
Range: Hex with 0x, at least 1 byte included for instance : 0x00 Default: 0x00 Tcl Parameter: N12NausfKhnPubKey Tcl Parameter: N13NudmKhnPubKey |
|
|
Available when Protection Scheme = Profile <A> or Profile <B>. Available on Service Based Node when AUSF (Nausf) is selected. How to generate Home Network Key pair: SSH to the Landslide test server or connect to any system that can execute the commands listed below: For Profile <A>:
For Profile <B> :
Range: Hex with 0x, at least 1 byte included for instance : 0x00 Default: 0x00 Tcl Parameter: NausfKhnPrivKey |
|
|
Enter the Routing Indicator. Per 3GPP 24.501, 9.11.3.4. (Should be in Binary-Coded decimal (BCD) format). Available in Service Based Nodal when (Test AUSF (Nausf), From AMF (N12), or Test UDM(Nudm), From AUSF (N13)) is selected. Options: Enter 1 to 4 Hex characters (0 to 9, or F) in BCD format with padded F (s) Default: F0FF Tcl Parameter: N12NausfRoutingInd Tcl Parameter: N13NudmRoutingInd |
|
|
Enter the MNC Length. Also available on UE Subtab in SMF Nodal test case. Available in Service Based Nodal when (Test AUSF (Nausf), From AMF (N12), or Test UDM(Nudm), From AUSF (N13)) is selected. Options: 2 or 3 Default: 3 Tcl Parameter: N13NudmMncLength Tcl Parameter: N12NausfMncLength |
NF Producer - Location data
|
Select to include Location Estimate information for the Location Response message. Available in Service Based Node test case when LMF (Nlmf) is enabled. Tcl Parameter: NlmfLocationEstimateEn |
|
|
Use the drop-down list to select whether Geographical Area reporting is supported and the type of information included in the Geographical Area IE of the Location Report message. The applicable parameters are enabled based on your selection. Options:
Default: Point Tcl Parameter: NlmfLocEstGeoAreaType |
|
|
Available for all Geographic Area Types except Polygon. Enter Latitude point coordinate in (°) degrees. Range : -90.0 to 90.0 Default: 39.9910665 Tcl Parameter: NlmfLocEstLatitude |
|
|
Available for all Geographic Area Types except Polygon. Enter Longitude point coordinate in (°) degrees. Range : -180.0 to 180.0 Default: 116.3586652 Tcl Parameter: NlmfLocEstLongtitude |
|
|
Available when Geographic Area Type = Point Uncertainty Circle. Enter the uncertainty for Point Uncertainty Circle in meters. Range : 0.0 to 1.7976931348623157E308 Default: 0.0 Tcl Parameter: NlmfLocEstUncertainty |
|
|
Uncertainty Semi Minor (m) Uncertainty Orientation (m) |
Available when Geographic Area Type = Point Uncertainty Ellipse or Point Altitude Uncertainty. Enter the Uncertainty Semi Major and Semi Minor in meters. Range : 0.0 to 1.7976931348623157E308 Default: 0.0 Tcl Parameter: NlmfLocEstUncertaintySemiMajor Tcl Parameter: NlmfLocEstUncertaintySemiMinor
Enter the Uncertainty Orientation. Range : 0 to 180 Default: 0 Tcl Parameter: NlmfLocEstUncertaintyOrientation |
|
Available when Geographic Area Type = Point Uncertainty Ellipse or Point Altitude Uncertainty or Ellipsoid Arc. Enter the Confidence in percentage value. Range : 0 to 100 Default: 0 Tcl Parameter: NlmfLocEstConfidence |
|
|
Available when Geographic Area Type = Point Altitude or Point Altitude Uncertainty. Enter the Altitude in meters. Range : -32767.0 to 32767.0 Default: 0.0 Tcl Parameter: NlmfLocEstAltitude |
|
|
Available when Geographic Area Type = Point Altitude Uncertainty. Enter the Uncertainty Altitude in meters. Range : 0.0 to 1.7976931348623157E308 Default: 0.0 Tcl Parameter: NlmfLocEstUncertaintyAltitude |
|
|
Inner Radius (m) Uncertain Radius (m) Offset Angle (°) Included Angle (°) |
Available when Geographic Area Type = Ellipsoid Arc. Enter the Inner Radius in meters. Range : 0 to 327675 Default: 0 Tcl Parameter: NlmfLocEstInnerRadius Enter the Uncertain Radius in meters. Range : 0.0 to 1.7976931348623157E308 Default: 0.0 Tcl Parameter: NlmfLocEstUncertaintyRadius Enter the Offset Angle and Included Angle in degrees. Range : 0 to 360 Default: 0 Tcl Parameter: NlmfLocEstOffsetAngle Tcl Parameter: NlmfLocEstIncludedAngle |
|
Available when Geographic Area Type = Polygon. Enter the Number of Points. Range : 3 to 15 Default: 3 Tcl Parameter: NlmfLocEstPointNum Enter the Latitude (Range : -90.0 to 90.0) and Longitude (Range : -180.0 to 180.0) for each Point. Tcl Parameter: Latitude_1 Tcl Parameter: Longitude_1 |
NF Consumer
|
Select the Nudm Version. Available when Test UDM (Nudm), From AMF (N8), From SMF (N10), From AUSF (N13), From SMSF (N21) is selected on Service Based Nodal test case on Interface AMF-UDM, SMF-UDM, SMSF-UDM and AUSF-UDM. Available when AUSF (Nausf) or (SMSF (Nsmsf) - To UDM (N21)) is selected on Service Based Node test case on Interface AUSF-UDM / SMSF-AMF. Available when UDM (N8) is selected on SMF Nodal test case on Interface AMF-UDM. Available when UDM (N8) is selected on AMF Node test case on Interface AMF-UDM. Available when N10 Interface is selected on SMF Node test case on Interface SMF-UDM. Options: 15.2.0/Dec2018, 15.2.1/Dec2018 (AMF/SMF Nodal/Node) , 15.4.0/Jun2019 , 16.2.0/Dec2019, 16.6.0/Dec2020 , 16.7.0/Mar2021 (Service Based test cases) Tcl Parameter: N8NudmSbiVersion Tcl Parameter: N10NudmSbiVersion Tcl Parameter: N13NudmSbiVersion Tcl Parameter: N21NudmSbiVersion |
|||||||||||||
|
Select “Use Access Token” option to support OAuth2 authorization for NF Consumer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Select to enter Access Token. Enter up to 1023 characters. Tcl Parameter: N8NudmUseAccTokEn Tcl Parameter: N8NudmAccTokEn Tcl Parameter: N8NudmAccTok Tcl Parameter: N10NudmUseAccTokEn Tcl Parameter: N10NudmAccTokEn Tcl Parameter: N10NudmAccTok Tcl Parameter: N13NudmUseAccTokEn Tcl Parameter: N13NudmAccTokEn Tcl Parameter: N13NudmAccTok Tcl Parameter: N17NudmUseAccTokEn Tcl Parameter: N17NudmAccTokEn Tcl Parameter: N17NudmAccTok Tcl Parameter: N21NudmUseAccTokEn Tcl Parameter: N21NudmAccTokEn Tcl Parameter: N21NudmAccTok Tcl Parameter: N29NnefUseAccTokEn Tcl Parameter: N29NnefAccTokEn Tcl Parameter: N29NnefAccTok |
|||||||||||||
| Neir Version (29.511) |
Select the Neir Version. Available when Test 5G-EIR (N5g-eir),From AMF (N17) is selected on Service Based Nodal test case on Interface AMF-5G-EIR. Options: 15.4.0/Jun2019 Tcl Parameter: N17NeirSbiVersion |
||||||||||||
| PEI |
Enter the PEI (Permanent Equipment Identifier) information (Starting IMEI and Software Version). Available when Test 5G-EIR (N5g-eir), From AMF (N17) is selected on Service Based Nodal test case on Interface AMF-5G-EIR. Enter the Starting IMEI - 14 digits. Default : 10310140000120. Select to enter the Software Version - 2 digits. Default : 00. Tcl Parameter: N17NeirImei Tcl Parameter: N17NeirSwverEn Tcl Parameter: N17NeirSwver |
||||||||||||
|
Select to include the Custom Http headers for Origination Timestamp and Max Response Time.
Nudm_SDM_Get Request (sdmSubscribeReq) and Nudm_UECM_Registration (uecmSmfRegisterReq) Request generated via the N10 (SMF-UDM) interface on Service Based Nodal test case will include these fields in the header. Request generated via the N29 (SMF-NEF) interface on Service Based Nodal test case will include these fields in the header. Enter Max response Time in milliseconds. Range : 1 to 60000 Default : 1 Tcl Parameter: N10Nudm3gppSbiOrigTimestampEn Tcl Parameter: N10Nudm3gppSbiMaxRspTimestamp Tcl Parameter: N29Nnef3gppSbiOrigTimestampEn Tcl Parameter: N29Nnef3gppSbiMaxRspTimestamp |
|||||||||||||
|
Available when UDM (N8) is selected on SMF Nodal test case on Interface AMF-UDM. Select the RAT Type. Available when UDM (N8) is selected on AMF Node test case on Interface AMF-UDM. Options: NR (default), EUTRA, WLAN, VIRTUAL Tcl Parameter: N8NudmRatType |
|||||||||||||
|
Available when UDM (N8) is selected on SMF Nodal test case on Interface AMF-UDM. Select to enter the IMS VoPS. Available when UDM (N8) is selected on AMF Node test case on Interface AMF-UDM. Options: HOMOGENEOUS SUPPORT (default), HOMOGENEOUS NON SUPPORT, NON HOMOGENEOUS OR UNKNOWN Tcl Parameter: N8NudmImsVoPSEn Tcl Parameter: N8NudmImsVoPS |
|||||||||||||
|
Available when UDM (N8) is selected on SMF Nodal test case on Interface AMF-UDM. Select to indicate P-CSCF Restoration Callback URI. Tcl Parameter: N8NudmPcscfRestorationCallbackUri |
|||||||||||||
| Separately Request for Subscription Data |
Available when UDM (N8) is selected on SMF Nodal test case on Interface AMF-UDM. Available when UDM (N8) is selected on AMF Node test case on Interface AMF-UDM. Select to Separately Request for Subscription Data. Tcl Parameter: N8NudmSepReqSubsDataEn |
||||||||||||
| Force NSSAI Validation |
Available when UDM (N8) is selected on SMF Nodal test case on Interface AMF-UDM. Available when UDM (N8) is selected on AMF Node test case on Interface AMF-UDM. Select to Force NSSAI Validation. Tcl Parameter: N8NudmForceNssaiValEn |
||||||||||||
|
|
Available when UDM (N8) is selected on SMF Nodal test case on Interface AMF-UDM. Available when UDM (N8) is selected on AMF Node test case on Interface AMF-UDM. Per 3GPP 29.503 table 6.1.6.2.3 SdmSubscription. Select Implicit Unsubscribe is false/true. If False, then select to enter Subscription Expire Time in seconds. Range : 1 to 4294967295 Default : 7200 Tcl Parameter: N8NudmImplicitUnsubEn Tcl Parameter: N8NudmImplicitUnsub Tcl Parameter: N8NudmSubExpireTimeEn Tcl Parameter: N8NudmSubExpireTime |
||||||||||||
|
Select "DNN with Starting SUPI Mode via TDF" to allocate the SUPI from the DNN entry in the TDF file. Each Row (Multiplier Label) is a different DNN. SBI Nodal can support up to 1500 unique DNNs. The SUPI values will be allocated based on the STARTING_SUPI and its range of each DNN entry from this TDF file.
The available columns of TDF file are:
STARTING_SUPI shall be numeric, at most 15 digts. SUPI_RANGE shall be numeric, in range 1..2147483647. PDU_INDEX shall be numeric, and in range 1..11. NSSAI has format as ([0-9][0-9]*)(-)([0-9a-f][0-9a-f])* or ([0-9][0-9])*, the first part is SST which value is from 0 to 255, the second part is SD which value is from 1 to 6 Hex characters, the two parts are combined with '-', and the first part shall be mandatory, the second part can be optional. DNN_NAME contains up to 63 characters, at least one character.
Tcl Parameter: N10NudmSmDnnSupiCfgFileEn Tcl Parameter: N10NudmSmDnnSupiCfgFile |
|||||||||||||
|
Available when Test UDM (Nudm), From SMF (N10) is selected on Service Based Nodal test case on Interface SMF-UDM. Enter up to 11 Protocol Data Unit (PDU) Sessions. Tcl Parameter: N10NudmNumPduSessions |
|||||||||||||
|
Enter DNN Pane details for each PDU Session (DNN is equivalent to APN).
|
|||||||||||||
|
Available when Test UDM (Nudm), From AUSF (N13) is selected on Service Based Nodal test case on Interface AUSF-UDM. Also available when Test AUSF (Nausf), From AMF (N12) is selected on Service Based Nodal test case on Interface AMF-AUSF. Enter the Secret Key . Range: Either String or HEX, If hex must start with 0x
Enter the Operator Variant. The 128-bit, operator-specific MILENAGE constant (OP) provisioned for the network. Range: Up to 16-Byte hex string Default: 0x63BFA50EE6523365FF14C1F45F88737D Enter the OPc. A128-bit value derived from OP and K and used in subsequent computations. Hence, less sensitive and if obtained by third party.
Range: Up to 16-Byte hex string Default: 0x63BFA50EE6523365FF14C1F45F88737D Tcl Parameter: N12NausfSecretKey Tcl Parameter: N12NausfOpVar Tcl Parameter: N12NausfOpC |
|||||||||||||
|
|
Select the Nausf Version. Available when Test AUSF (Nausf), From AMF (N12) is selected on Service Based Nodal test case on Interface AMF-AUSF. Available on AMF Node when N12 Interface is enabled. Options: 15.2.0/Dec2018 (default for Service Based Nodal) , 15.2.1/Dec2018 , (default for AMF Node) , 15.4.0/Jun2019 , 16.6.0/Dec2020 Tcl Parameter: N12NausfSbiVersion |
||||||||||||
|
Select “Use Access Token” option to support OAuth2 authorization for NF Consumer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Select to enter Access Token. Enter up to 1023 characters. Tcl Parameter: N12NausfUseAccTokEn Tcl Parameter: N12NausfAccTokEn Tcl Parameter: N12NausfAccTok |
|||||||||||||
| Npcf Version (29.507) |
Available on Service Based Node Emulator Configuration when To H-PCF (N24) is enabled. Select the Npcf Version. Options: 15.2.0/Dec2018 , 15.4.0/Jun2019 , 16.7.0/Mar2021, 17.7.0/Jun2022 Tcl Parameter: N24NpcfSbiVersion |
||||||||||||
|
Select “Use Access Token” option to support OAuth2 authorization for NF Consumer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Select to enter Access Token. Enter up to 1023 characters. Tcl Parameter: N24NpcfUseAccTokEn Tcl Parameter: N24NpcfAccTokEn Tcl Parameter: N24NpcfAccTok |
|||||||||||||
| H-PCF PLMN |
Available on Service Based Node Emulator Configuration when To H-PCF (N24) is enabled on the PCF - PCF Tab. Enter the MCC and MNC of the H-PCF PLMN. Mobile Country Code (MCC) - Enter 3 digits . Default : 000 Mobile Network Code (MCC) - Enter 2 to 3 digits . Default : 00 Tcl Parameter: N24NpcfHpcfMcc Tcl Parameter: N24NpcfHpcfMnc |
NF Consumer Nnrf Client (Additional data fields for NRF Interface and Test NRF (Nnrf) )
|
Select the NnrfCln Version. Available when NRF Interface is selected on AMF Nodal / AMF Node, SMF Nodal / SMF Node test case on Interface Nnrf Client. Available when NRF Interface and Test NRF (Nnrf) is selected on Service Based Nodal test case on Interface Nnrf Client. Options: 15.2.0/Dec2018 (default) , 15.4.0/Jun2019, 16.6.0/Dec2020 Tcl Parameter: NnrfClnSbiVersion |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| NF register to NRF with FQDN only |
Available on Nnrf Client tab, only on AMF Node, SMF Node , Service Based Nodal and Node test cases when NRF Interface and is enabled. Select to emulate NF register to NRF with FQDN (Fully Qualified Domain Name) only. Per 29.510 6.2.6.2.4 Type: NFService - Definition of type NFService NOTE 5: If the ipEndPoints attribute is absent in the NF Service and NF Profile, the NF service consumer shall use the fqdn attribute value for DNS query.
Tcl Parameter: NnrfClnRegWithFqdnOnlyEn |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| NRF register to NRF In Same PLMN Delay (s) |
Available on Nnrf Client tab, only on Service Based Node test case when NRF (Nnrf) and To NRF in Same PLMN are enabled. Select to NRF register to NRF in the same PMLN. Per 3GPP TS 23.510, section 5.2.2.2. Enter delay for NRF register to NRF in seconds. Range : 10 to 65535 Default : 10 Tcl Parameter: NnrfClnRegNrfSamePlmnDelayEn Tcl Parameter: NnrfClnRegNrfSamePlmnDelayTime |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Emulate Reporting NF Load |
Available on Nnrf Client tab on Service Based Nodal test case when NRF Interface and Test NWDAF (Nnwdaf) are enabled. Select to support emulating reporting NF Load to NRF. Tcl Parameter: NnrfClnEmuNfLoadEn |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Select NF Profile Complete Update and enter the Update Period in seconds. Available when NRF Interface is selected on SMF Nodal, SMF Node, and AMF Node test cases on Interface Nnrf Client. Available when NRF Interface and Test NRF (Nnrf) are selected on Service Based Nodal test case on Interface Nnrf Client. Range : 1 to 65535 Default : 60 Tcl Parameter: NnrfClnNFProfCompUpdateEn Tcl Parameter: NnrfClnNFProfCompUpdatePeriod |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Select NF Profile Partial Update and enter the Update Delay in seconds.
Available when NRF Interface and Test NRF (Nnrf) are selected on Service Based Nodal and AMF Node test cases on Interface Nnrf Client. Range : 1 to 65535 Default : 60 Tcl Parameter: NnrfClnNFProfPartUpateEn Tcl Parameter: NnrfClnNFProfPartUpdateDelay |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
Select to be able to generate a customized discovery query as needed for each NF when NRF is enabled. Based on 3GPP TS 29.510 version 15.4.0 Release- Table 6.2.3.2.3.1-1: URI query parameters supported by the GET method on this resource. Tabs are available to differentiate SMF discovery parameters or UDM discovery parameters on SMF Nodal test case.
Tabs are available to differentiate discovery parameters for each node type on Service Based Nodal test case.
WhenDelegate NF Discovery And Selection is enabled on Service Based Nodal or Service Based Node test cases, the NF Discovery tab becomes available for input. It contains the NF Discovery Query Parameters for selection without these options: limit, max-payload-size, requester-nf-type, requester-snssais, smf-serving-area, supported-features, target-nf-type. For complex-query the JSON value type = object and the default = {"cnfUnits":[{"cnfUnit":[{"attr":"1","value":"1"}]}]}
NF Discovery Tab:
Nnrf Client Tab : Available on Nnrf Client - NF Consumer Tab for AMF Node, SMF Nodal/Node when NRF Interface is enabled.
The parameters listed below are available on both NF Discovery Tab and Nnrf Client Tab with some minor differences identified here: Select Query Parameter and Operation- Options : Append and Overwrite. Default is "Append". Select Customize and Name of "Parameter" - Enter JSON Query in the panel on the right. The JSON value type will be displayed in the panel. The editor is closely related to the SBI Message Editor but presented with the selection table to the left and the selected value editor tab to the right. Each parameter has an associated JSON type, which is displayed in the editor when the parameter is selected. The validation of the value is based on the parameter type. Example : Parameter "chf-supported-plm" is of JSON parameter type - object. Example : Parameter "amf-region-id" is of JSON parameter type - string. e.g. "\[\"apple\"]" Parameter Types : null, number, string, object, array, bool Added support for Auto Increment - only editable when the NF Discovery Query Parameter JSON value type is "object" or "array" or "String". In the Test NRF mode, all of the NF tabs shown in the confluence page will always be present and only in Test NRF will the Auto-Increment option be available.
The NF consumer tab on NF Discovery has a fixed "From NF" being the consumer NF type and only one row is allowed in the Auto-Increment table. Add up to 16 rows on Nnrf Tab, up to 1 on the NF Discovery Tab : From NF Type : Options : AMF, SMF, UDM, AUSF, PCF, vNRF, SMSF, NSSF, UDR, BSF, CHF. The NF consumer tab on NF Discovery has a fixed "From NF" being the consumer NF type. Select Auto-Increment Type : String, HEX Digits , IPv4 Address, IPv6 Address, IPv6 Prefix, UE ID, Number, General String : Enter up to 1024 characters enclosed in quotations Hex Digits : Enter up to 1024 Hex characters enclosed in quotations IPv4 Address : Enter a valid IPv4 address enclosed in quotations IPv6 Address : Enter a valid IPv6 address enclosed in quotations IPv6 Prefix : Enter a valid IPv6 Prefix enclosed in quotations - [Ipv6address] / [prefix length] UE ID : used to support auto-increment for GPSI, SUPI, PEI etc, UE ID like string. For PEI with prefix "imei-" or "imeisv-", it will auto increment the IMEI part, the first 14 digits of the last digital part. For SUPI with prefix "imsi-" and GPSI with prefix "msisdn-", it will auto increment the entire last digital part. For other ID format, just simply auto increment the entire last digital part if any. Example: "imeisv-1031014001112000" - Enter up to 1024 characters enclosed in quotations Number : Enter a number General : Available for Value Type = String only with Auto-Increment field (N). Default value "spirent.com". Click Example:
Enter Auto-Increment Value. Enter up to 1024 characters enclosed in quotations. Enter Auto-Increment Rollover Value. Range : 0 to 4294967295. 0 = No rollover. Enter Path : only editable when the NF Discovery Query Parameter JSON value type is "object" or "array"
27 NF Consumer tabs in Service Based Nodal (sorted by Producer) support the NF Discovery Tab: AMF-AUSF 15 NF Consumer tabs in Service Based Node (sorted by Producer) support the NF Discovery Tab: CBCF-AMF, GMLC-AMF, LMF-AMF, NEF-AMF, PCF-AMF, SMSF-AMF Note the TCL variable configuration for the Auto-Increment table in the NF Discovery Tab for each interface that is supported is as follows: Example : Interface AMF-AUSF (N12Nausf) N12NausfNfDscAutoIncEn_i - Auto-Increment enabler N12NausfNfDscAutoIncNum_i - Number of rows in Auto-Increment table N12NausfNfDscAutoIncFrom_i_j - From NF Type in Auto-Increment table N12NausfNfDscAutoIncType_i_j - Auto-increment Type in Auto-Increment table N12NausfNfDscAutoIncValue_i_j - Auto-increment Value in Auto-Increment table N12NausfNfDscAutoIncRollover_i_j - Rollover in Auto-Increment table N12NausfNfDscAutoIncPath_i_j - Path in Auto-Increment table
Tcl Parameter: NnrfClnNfDscParNum Tcl Parameter: NnrfClnNfDscParName_1 Tcl Parameter: NnrfClnNfDscParValue_1 Tcl Parameter: NnrfClnNfDscUdmParNum Tcl Parameter: NnrfClnNfDscUdmParName_1 Tcl Parameter: NnrfClnNfDscUdmParValue_1 Tcl Parameter: NnrfClnNfDscPcfParNum Tcl Parameter: NnrfClnNfDscPcfParName_1 Tcl Parameter: NnrfClnNfDscPcfParValue_1 Tcl Parameter: NnrfClnNfDscAusfParNum Tcl Parameter: NnrfClnNfDscAusfParName_1 Tcl Parameter: NnrfClnNfDscAusfParValue_1 Tcl Parameter: NnrfClnNfDscChfParNum Tcl Parameter: NnrfClnNfDscChfParName_1 Tcl Parameter: NnrfClnNfDscChfParValue_1 Tcl Parameter: NnrfClnNfDscNssfParNum Tcl Parameter: NnrfClnNfDscNssfParName_1 Tcl Parameter: NnrfClnNfDscNssfParValue_1 Tcl Parameter: NnrfClnNfDscNefParNum Tcl Parameter: NnrfClnNfDscNefParName_1 Tcl Parameter: NnrfClnNfDscNefParValue_1 Tcl Parameter: NnrfClnNfDscLmfParNum Tcl Parameter: NnrfClnNfDscLmfParName_1 Tcl Parameter: NnrfClnNfDscLmfParValue_1 Tcl Parameter: NnrfClnNfDscUdrParNum Tcl Parameter: NnrfClnNfDscUdrParName_1 Tcl Parameter: NnrfClnNfDscUdrParValue_1 Tcl Parameter: NnrfClnNfDscSlfParNum Tcl Parameter: NnrfClnNfDscSlfParName_1 Tcl Parameter: NnrfClnNfDscSlfParValue_1 Tcl Parameter: NnrfClnNfDscSmsfParNum Tcl Parameter: NnrfClnNfDscSmsfParName_1 Tcl Parameter: NnrfClnNfDscSmsfParValue_1 Tcl Parameter: NnrfClnNfDscAmfAutoIncEn_1 Tcl Parameter: NnrfClnNfDscAmfAutoIncNum_1 Tcl Parameter: NnrfClnNfDscAmfAutoIncFrom_1_1 Tcl Parameter: NnrfClnNfDscAmfAutoIncType_1_1 Tcl Parameter: NnrfClnNfDscAmfAutoIncValue_1_1 Tcl Parameter: NnrfClnNfDscAmfAutoIncRollover_1_1 Tcl Parameter: NnrfClnNfDscAmfAutoIncPath_1_1 Tcl Parameter: NnrfClnNfDscAusfAutoIncEn_1 Tcl Parameter: NnrfClnNfDscAusfAutoIncNum_1 Tcl Parameter: NnrfClnNfDscAusfAutoIncFrom_1_1 Tcl Parameter: NnrfClnNfDscAusfAutoIncType_1_1 Tcl Parameter: NnrfClnNfDscAusfAutoIncValue_1_1 Tcl Parameter: NnrfClnNfDscAusfAutoIncRollover_1_1 Tcl Parameter: NnrfClnNfDscAusfAutoIncPath_1_1 Tcl Parameter: NnrfClnNfDscChfAutoIncEn_1 Tcl Parameter: NnrfClnNfDscChfAutoIncNum_1 Tcl Parameter: NnrfClnNfDscChfAutoIncFrom_1_1 Tcl Parameter: NnrfClnNfDscChfAutoIncType_1_1 Tcl Parameter: NnrfClnNfDscChfAutoIncValue_1_1 Tcl Parameter: NnrfClnNfDscChfAutoIncRollover_1_1 Tcl Parameter: NnrfClnNfDscChfAutoIncPath_1_1 Tcl Parameter: NnrfClnNfDscBsfAutoIncEn_1 Tcl Parameter: NnrfClnNfDscBsfAutoIncNum_1 Tcl Parameter: NnrfClnNfDscBsfAutoIncFrom_1_1 Tcl Parameter: NnrfClnNfDscBsfAutoIncType_1_1 Tcl Parameter: NnrfClnNfDscBsfAutoIncValue_1_1 Tcl Parameter: NnrfClnNfDscBsfAutoIncRollover_1_1 Tcl Parameter: NnrfClnNfDscBsfAutoIncPath_1_1 Tcl Parameter: NnrfClnNfDscEirAutoIncEn_1 Tcl Parameter: NnrfClnNfDscEirAutoIncNum_1 Tcl Parameter: NnrfClnNfDscEirAutoIncFrom_1_1 Tcl Parameter: NnrfClnNfDscEirAutoIncType_1_1 Tcl Parameter: NnrfClnNfDscEirAutoIncValue_1_1 Tcl Parameter: NnrfClnNfDscEirAutoIncRollover_1_1 Tcl Parameter: NnrfClnNfDscEirAutoIncPath_1_1 Tcl Parameter: NnrfClnNfDscLmfAutoIncEn_1 Tcl Parameter: NnrfClnNfDscLmfAutoIncNum_1 Tcl Parameter: NnrfClnNfDscLmfAutoIncFrom_1_1 Tcl Parameter: NnrfClnNfDscLmfAutoIncType_1_1 Tcl Parameter: NnrfClnNfDscLmfAutoIncValue_1_1 Tcl Parameter: NnrfClnNfDscLmfAutoIncRollover_1_1 Tcl Parameter: NnrfClnNfDscLmfAutoIncPath_1_1 Tcl Parameter: NnrfClnNfDscNefAutoIncEn_1 Tcl Parameter: NnrfClnNfDscNefAutoIncNum_1 Tcl Parameter: NnrfClnNfDscNefAutoIncFrom_1_1 Tcl Parameter: NnrfClnNfDscNefAutoIncType_1_1 Tcl Parameter: NnrfClnNfDscNefAutoIncValue_1_1 Tcl Parameter: NnrfClnNfDscNefAutoIncRollover_1_1 Tcl Parameter: NnrfClnNfDscNefAutoIncPath_1_1 Tcl Parameter: NnrfClnNfDscNssfAutoIncEn_1 Tcl Parameter: NnrfClnNfDscNssfAutoIncNum_1 Tcl Parameter: NnrfClnNfDscNssfAutoIncFrom_1_1 Tcl Parameter: NnrfClnNfDscNssfAutoIncType_1_1 Tcl Parameter: NnrfClnNfDscNssfAutoIncValue_1_1 Tcl Parameter: NnrfClnNfDscNssfAutoIncRollover_1_1 Tcl Parameter: NnrfClnNfDscNssfAutoIncPath_1_1 Tcl Parameter: NnrfClnNfDscPcfAutoIncEn_1 Tcl Parameter: NnrfClnNfDscPcfAutoIncNum_1 Tcl Parameter: NnrfClnNfDscPcfAutoIncFrom_1_1 Tcl Parameter: NnrfClnNfDscPcfAutoIncType_1_1 Tcl Parameter: NnrfClnNfDscPcfAutoIncValue_1_1 Tcl Parameter: NnrfClnNfDscPcfAutoIncRollover_1_1 Tcl Parameter: NnrfClnNfDscPcfAutoIncPath_1_1 Tcl Parameter: NnrfClnNfDscSlfAutoIncEn_1 Tcl Parameter: NnrfClnNfDscSlfAutoIncNum_1 Tcl Parameter: NnrfClnNfDscSlfAutoIncFrom_1_1 Tcl Parameter: NnrfClnNfDscSlfAutoIncType_1_1 Tcl Parameter: NnrfClnNfDscSlfAutoIncValue_1_1 Tcl Parameter: NnrfClnNfDscSlfAutoIncRollover_1_1 Tcl Parameter: NnrfClnNfDscSlfAutoIncPath_1_1 Tcl Parameter: NnrfClnNfDscSmfAutoIncEn_1 Tcl Parameter: NnrfClnNfDscSmfAutoIncNum_1 Tcl Parameter: NnrfClnNfDscSmfAutoIncFrom_1_1 Tcl Parameter: NnrfClnNfDscSmfAutoIncType_1_1 Tcl Parameter: NnrfClnNfDscSmfAutoIncValue_1_1 Tcl Parameter: NnrfClnNfDscSmfAutoIncRollover_1_1 Tcl Parameter: NnrfClnNfDscSmfAutoIncPath_1_1 Tcl Parameter: NnrfClnNfDscSmsfAutoIncEn_1 Tcl Parameter: NnrfClnNfDscSmsfAutoIncNum_1 Tcl Parameter: NnrfClnNfDscSmsfAutoIncFrom_1_1 Tcl Parameter: NnrfClnNfDscSmsfAutoIncType_1_1 Tcl Parameter: NnrfClnNfDscSmsfAutoIncValue_1_1 Tcl Parameter: NnrfClnNfDscSmsfAutoIncRollover_1_1 Tcl Parameter: NnrfClnNfDscSmsfAutoIncPath_1_1 Tcl Parameter: NnrfClnNfDscUdmAutoIncEn_1 Tcl Parameter: NnrfClnNfDscUdmAutoIncNum_1 Tcl Parameter: NnrfClnNfDscUdmAutoIncFrom_1_1 Tcl Parameter: NnrfClnNfDscUdmAutoIncType_1_1 Tcl Parameter: NnrfClnNfDscUdmAutoIncValue_1_1 Tcl Parameter: NnrfClnNfDscUdmAutoIncRollover_1_1 Tcl Parameter: NnrfClnNfDscUdmAutoIncPath_1_1 Tcl Parameter: NnrfClnNfDscUdrAutoIncEn_1 Tcl Parameter: NnrfClnNfDscUdrAutoIncNum_1 Tcl Parameter: NnrfClnNfDscUdrAutoIncFrom_1_1 Tcl Parameter: NnrfClnNfDscUdrAutoIncType_1_1 Tcl Parameter: NnrfClnNfDscUdrAutoIncValue_1_1 Tcl Parameter: NnrfClnNfDscUdrAutoIncRollover_1_1 Tcl Parameter: NnrfClnNfDscUdrAutoIncPath_1_1 Tcl Parameter: NnrfClnNfDscUpfAutoIncEn_1 Tcl Parameter: NnrfClnNfDscUpfAutoIncNum_1 Tcl Parameter: NnrfClnNfDscUpfAutoIncFrom_1_1 Tcl Parameter: NnrfClnNfDscUpfAutoIncType_1_1 Tcl Parameter: NnrfClnNfDscUpfAutoIncValue_1_1 Tcl Parameter: NnrfClnNfDscUpfAutoIncRollover_1_1 Tcl Parameter: NnrfClnNfDscUpfAutoIncPath_1_1 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Access Token Request Attributes |
Available on the same tabs as NF Discovery Query Parameters. See above. Select for support of AccessTokenReq parameter customization and Token Claim validation. Available when at least there is one consumer (e.g. AMF-UDM) has enabled "Use Access Token" and disabled Access Token. Options :
The Tcl variable name takes the prefix "NnrfClnAccTokReq". For example, the Tcl variable name for the corresponding attribute could be NnrfClnAccTokReqUdmParName_x, where x is the index. Tcl Parameter: NnrfClnAccTokReqUdmParValue_1 |
| Subscription Data |
Select to Enable Subscription Data. Available when Test NRF (Nnrf) and NRF Interface are enabled. Available when NRF Interface and CBCF are enabled on Service Based Node test case on Interface Nnrf Client. Available when NRF Interface is selected on SMF Nodal / SMF Node test case on Interface Nnrf Client. Enter the Number of Subscription Data. Range : 1 to 8 Default : 1 Tcl Parameter: NnrfClnSubDataEn Tcl Parameter: NnrfClnSubDataNum Identification of a Network Slice is done via the Single Network Slice Selection Assistance Information (S-NSSAI). The NSSAI (Network Slice Selection Assistance Information) is a collection of S-NSSAIs.
|
NF Producer Nsmf (Additional data fields for Test NRF (Nnrf) - Emulate SMF)
| S-NSSAI SMF Info |
Enter the Number of Infos. Available when Test NRF (Nnrf) and Emulate SMF are enabled. Available when NRF Interfaceis enabled on SMF Node test case. Range : 1 to 8 Default : 1 For each info enter the S-NSSAI (SST, SD) and Number DNNs. Tcl Parameter: NsmfInfoNum Identification of a Network Slice is done via the Single Network Slice Selection Assistance Information (S-NSSAI). The NSSAI (Network Slice Selection Assistance Information) is a collection of S-NSSAIs.
|
NF Producer Nudm (Additional data fields for Test NRF (Nnrf) - Emulate UDM)
| Enable UDM Info |
Select to enable UDM info. Available when Test NRF (Nnrf) and Emulate UDM are enabled. Tcl Parameter: NudmInfoEn
|
NF Producer Nudm (Additional data fields for Test NRF (Nnrf) - Emulate UDR)
| Enable UDR Info |
Select to enable UDR info. Available when Test NRF (Nnrf) and Emulate UDR are enabled. Tcl Parameter: NudrInfoEn
|
NF Producer Nudm (Additional data fields for Test NRF (Nnrf) - Emulate CHF)
| Enable CHF Info |
Select to enable UDM info. Available when Test NRF (Nnrf) and Emulate CHF are enabled. Tcl Parameter: NchfInfoEn
|
NF Producer Nausf (Additional data fields for Test NRF (Nnrf) - Emulate AUSF)
| Enable AUSF Info |
Select to enable AUSF info. Available when Test NRF (Nnrf) and Emulate AUSF are enabled. Tcl Parameter: NausfInfoEn
|
NF Producer Npcf (Additional data fields for Test NRF (Nnrf) - Emulate PCF)
| Enable PCF Info |
Select to enable AUSF info. Available when Test NRF (Nnrf) and Emulate PCF are enabled. Tcl Parameter: NpcfInfoEn
|
SCP / SCP-NF
| SCP Version (29.500) |
Select the SCP version. Available in Service Based Node when SCP is enabled. Options : 15.2.0/Dec2018 (default), 15.4.0/Jun2019 Tcl Parameter: ScpSbiVersion |
||
| API Prefix |
Select to enter the API Prefix for SCP-NF. Available in Service Based Node when SCP is enabled. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter:
|
||
| Register and Subscribe to NRF |
Available in Service Based Node when SCP is enabled and NRF Interface are enabled. Select Register and Subscribe to NRF for receiving notification, emulated by SCP Node, for enhancement of interworking between Other NFs and target NFs via SCP. Reference : 3GPP TS 29.510 version 15.1.0 Release 15 Section 5.2.2.1
"The NRF shall allow the registration of a Network Function instance with any of the NF types described in subclause 6.1.6.3.3, and it shall also allow registration of Network Function instances with custom NF types (e.g., NF type values not defined by 3GPP, or NF type values not defined by this API version)." Emulated SCP node enhanced to :
Tcl Parameter: ScpRegisterAndSubToNrfEn |
||
|
Append Suffix |
Available in Service Based Node when SCP is enabled. Enable the generic modification of the "Location Header" for URI in 5g-AKA-confirm request based on the location header of previous 201 response of UE-authentication from AUSF. When enabled, Append Suffix becomes available for selection to enter up to 30 UPI path chars. Spec reference :29.509 v16.1.0 Default : ~spirentscp~ Tcl Parameter: ScpLocHdrModifyEn Tcl Parameter: ScpLocHdrAppendSuffixEn Tcl Parameter: ScpLocHdrSuffix |
NF Producer Nbsf, (NEF-BSF), (PCF-BSF)
| Nbsf Version (29.521) |
Select the Nbsf (Binding Support Function) Version (29.521). Available when ( Test BSF (Nbsf) and From PCF) / From AF) or (Test NRF (Nnrf) and Emulate BSF are enabled) on Service Based Nodal test case and when BSF (Nbsf) is enabled on Service based Node test case. Available on DRA Nodal Test Cnfg, test case when PCRF Interface (Nbsf, Nnrf) is enabled. Available when NEF (Nnef) and To BSF/PCF (Nbsf/N30) is enabled on Service Based Node Emulator Configuration. Options: 15.4.0/Jun2019 Services to be supported: Per 3GPP TS 29.521 version 15.4.0 section 4.2 Service Operations. BSF provides a PDU session binding functionality, which ensures that an AF request for a certain PDU Session reaches the relevant PCF holding the PDU Session information. This service: * Allows PCF consumers to register, update and remove the binding information; *our PCF Consumer update function, need to deregister first and then register with choose flag “update session binding” on message flow “Body Argument”. * allows NF consumers to retrieve the binding information. We achieve PCF register, update, remove on BSF, AF discover PCF on BSF, and BSF Rx Proxy/Redirect between AF-PCF.
Service Operation Names: * Nbsf_Management_Register , NF service consumer (PCF) - (message flow - nbsfMgtRegisterReq ( 20301) - nbsfMgtRegisterResp - (20302)) * Nbsf_Management_Deregister, NF service consumer (PCF) - (message flow - nbsfMgtDeregisterReq ( 20303) - nbsfMgtDeregisterResp - (20304)) * Nbsf_Management_Discover, NF service consumer (NEF, AF) - (message flow - nbsfMgtDiscoverReq ( 20305) - nbsfMgtDeregisterResp - (20306))
For Diameter RX, on DRA Nodal Test Cnfg, the default conditions are: * Start PCF register flow before diameter message flow starts * Start PCF de-register flow after diameter message flow stops On Rx, we support BSF Proxy and Redirect function.
Tcl Parameter: NbsfSbiVersion Tcl Parameter: NafNbsfSbiVersion Tcl Parameter: NpcfNbsfSbiVersion Tcl Parameter: NnefNbsfSbiVersion |
|||||||||||||
| API Prefix |
Select to enter the API Prefix for Nbsf. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: NbsfApiPrefixEn Tcl Parameter: NbsfApiPrefix |
|||||||||||||
| Validate Access Token |
Select Validate Access Token to support OAuth2 Authorization for NF Producer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Select to Validate Expiration Time. Configurable only when "Validate Access Token" is enabled. Tcl Parameter: NbsfValidateAccTokEn Tcl Parameter: NbsfAccTokSecKey Tcl Parameter: NbsfValidateAccTokExpireTimeEn |
|||||||||||||
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: NbsfDefaultHostFormat |
|||||||||||||
|
Select “Use Access Token” option to support OAuth2 authorization for NF Consumer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Select to enter Access Token. Enter up to 1023 characters. Tcl Parameter: NafNbsfUseAccTokEn Tcl Parameter: NafNbsfAccTokEn Tcl Parameter: NafNbsfAccTok Tcl Parameter: NpcfNbsfUseAccTokEn Tcl Parameter: NpcfNbsfAccTokEn Tcl Parameter: NpcfNbsfAccTok Tcl Parameter: NnefNbsfUseAccTokEn Tcl Parameter: NnefNbsfAccTokEn Tcl Parameter: NnefNbsfAccTok |
||||||||||||||
|
Select to include the Custom Http headers for Origination Timestamp and Max Response Time.
Enter Max response Time in milliseconds. Range : 1 to 60000 Default : 1 Tcl Parameter: NafNbsf3gppSbiOrigTimestampEn Tcl Parameter: NafNbsf3gppSbiMaxRspTimestamp Tcl Parameter: NpcfNbsf3gppSbiOrigTimestampEn Tcl Parameter: NpcfNbsf3gppSbiMaxRspTimestamp |
||||||||||||||
| Number of PDU Sessions |
Available when ( Test BSF (Nbsf) and From PCF) / From AF) and Test NEF (Nnef), From AF (N33) is enabled on Service Based Nodal test case and and when BSF (Nbsf) is enabled on Service based Node test case. Enter up to 11 Protocol Data Unit (PDU) Sessions. Tcl Parameter: NbsfPduSessionNum Tcl Parameter: NpcfNbsfNumPduSessions |
|||||||||||||
| Routing Action Host Usage Max Cache |
Available when BSF (Nbsf) is enabled on DRA Node test case. Select the Routing Action. Options : Proxy, redirect When Routing Action = redirect, enter the Host Usage and Max Cache. Select the Host Usage. Options : None, DONT_CACHE, ALL_SESSION, ALL_REALM, REALM_AND_APPLICATION, ALL_APPLICATION, ALL_HOST , ALL_USER Enter Max Cache. Range : 1 to 4294967295, Default : 1000 Tcl Parameter: NbsfRoutAct Tcl Parameter: NbsfHostUsage Tcl Parameter: NbsfMaxCache |
|||||||||||||
| Enable BSF Info |
Select to enable BSF info. Available when Test NRF (Nnrf) and Emulate BSF are enabled , when BSF (Nbsf) is enabled on Service based Node test case and when BSF (Nbsf) is enabled on DRA Node test case. Tcl Parameter: NbsfInfoEn
|
|||||||||||||
|
or AF-BSF |
Available when (Test BSF (Nbsf) and From PCF) is enabled on Service based Nodal test case under PCF-BSF tab and when Test BSF (Nbsf), From AF is enabled on Service based Nodal test case. 3GPP TS29.521 V15.4.0 - Nbsf_Management_Discovery Select Support Multiple Messages to enable Number of PDU Sessions to support multiple bindings per UE. when enabled, multiple "Session Binding Info" sessions panes (up to 11) become available for input. Enter the details provided below. Support Multiple Messages is not available when Test NEF (Nnef), From AF (N33) is enabled.
Tcl Parameter: NafNbsfSupMulMsgEn Tcl Parameter: NafNbsfNumPduSessionsMult Tcl Parameter: NpcfNbsfSupMulMsgEn Tcl Parameter: NpcfNbsfNumPduSessionsMult
Update Session Binding InfoAvailable when (Test BSF (Nbsf) and From PCF) is enabled on Service based Nodal test case under PCF-BSF tab.
|
NF Producer Ncapifcf / NF Consumer NEF-CAPIF
| CAPIF Version (29.122) |
Select the CAPIF (Network Exposure Function Nb) Version (29.222). Available when CAPIF CF (Ncapifcf) or when NEF (Nnef) and To CAPIF-3/4/5 are enabled on Service Based Node Emulator Configuration. Options: 18.4.0/Dec2023 Tcl Parameter: NcapifcfSbiVersion |
| API Prefix |
Select to enter the API Prefix for capifcf. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: NcapifcfApiPrefixEn Tcl Parameter: NcapifcfApiPrefix |
| Validate Access Token |
Select Validate Access Token to support OAuth2 Authorization for NF Producer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Select to Validate Expiration Time. Configurable only when "Validate Access Token" is enabled. Tcl Parameter: NcapifcfValidateAccTokEn Tcl Parameter: NcapifcfAccTokSecKey Tcl Parameter: NcapifcfValidateAccTokExpireTimeEn |
| Origination Timestamp |
Select to include the Custom Http headers for Origination Timestamp and Max Response Time.
Enter Max response Time in milliseconds. Range : 1 to 60000 Default : 1 Tcl Parameter: NcapifcfTime3gppSbiOrigTimestampEn Tcl Parameter: NcapifcfTime3gppSbiMaxRspTimeStamp |
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: NcapifcfDefaultHostFormat |
| Use Access Token |
Select “Use Access Token” option to support OAuth2 authorization for NF Consumer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Select to enter Access Token. Enter up to 1023 characters Tcl Parameter: NnefNcapifUseAccTokEn Tcl Parameter: NnefNcapifAccTokEn Tcl Parameter: NnefNcapifAccTok |
| API Publishing Function ID |
Each NEF Node has one API Publishing Function. Enter up to 128 characters with auto-increment allowed. Click Default : spirent-apfid#(N1) Tcl Parameter: NnefNcapifApfid |
| API Supported Features |
Enter the API Supported features. Hex string 1 to 7 characters. Default : 1 Tcl Parameter: NnefNcapifApiSuppFeat |
| API Update/Modify Interval (ms) |
Select to enter the API update / modify interval in milliseconds. Range : 500 to 600000 Default : 1000 Tcl Parameter: NnefNcapifUpModIntervalEn Tcl Parameter: NnefNcapifUpModInterval |
NF Producer NnefNb
| NnefNb Version (29.122) |
Select the NnefNb (Network Exposure Function Nb) Version (29.122). Available when NEF (Nnef) and ( To BSF/PCF (Nbsf/N30) or Enable Northbound ) is enabled on Service Based Node Emulator Configuration. Options: 15.4.0/Jun2019, 16.7.0/Sept2020 Tcl Parameter: NnefNbSbiVersion |
| API Prefix |
Select to enter the API Prefix for NefNb. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: NnefNbApiPrefixEn Tcl Parameter: NnefNbApiPrefix |
| Validate Access Token |
Select Validate Access Token to support OAuth2 Authorization for NF Producer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Select to Validate Expiration Time. Configurable only when "Validate Access Token" is enabled. Tcl Parameter: NnefNbValidateAccTokEn Tcl Parameter: NnefNbAccTokSecKey Tcl Parameter: NnefNbValidateAccTokExpireTimeEn |
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: NnefNbDefaultHostFormat |
| Max # of Chargeable Party Transactions to Return |
Enter the Maximum number of Chargeable Party Transactions to Return. Range : 1 to 16 Default : 1 Tcl Parameter: NnefNbMaxRtnNumChaPartyTran |
| # of PDU Session |
Enter the # of PDU Sessions. Range : 1 to 11 Default : 1 Enter Address. Select Address Type (IPv4, IPv6, MAC) and enter a valid IP Address based on selected address type. Tcl Parameter: NnefNbPduSessionNum Tcl Parameter: NnefNbAddrType_1 Tcl Parameter: NnefNbAddrVal_1 |
NF Consumer NEF-PCF
| Npcf Version (29.514) |
Additional details in topic Nef to Pcf NF Tab. |
| Use Access Token | Additional details in topic Nef to Pcf NF Tab. |
| Supported Features | Additional details in topic Nef to Pcf NF Tab. |
NF Producer Nsmf (Additional data fields for Test NRF (Nnrf) - Emulate UPF)
| PFCP Version (29.244) |
Select the PFCP (Packet Forwarding Control Protocol) Version (29.244). Available when (Test NRF (Nnrf) and Emulate UPF are enabled) on Service Based Nodal test case. Options: 15.2.0/Dec2018 (default), 15.4.0/Jun2019 Tcl Parameter: UpfSbiVersion |
| API Prefix |
Select to enter the API Prefix for UPF. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: UpfApiPrefixEn Tcl Parameter: UpfApiPrefix |
| Validate Access Token |
Select Validate Access Token to support OAuth2 Authorization for NF Producer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.
Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Select to Validate Expiration Time. Configurable only when "Validate Access Token" is enabled. Tcl Parameter: UpfValidateAccTokEn Tcl Parameter: UpfAccTokSecKey Tcl Parameter: UpfValidateAccTokExpireTimeEn |
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: UpfDefaultHostFormat |
| S-NSSAI UPF Info |
Enter the Number of Infos. Available when Test NRF (Nnrf) and Emulate UPF are enabled. Range : 1 to 8 Default : 1 For each info enter the S-NSSAI (SST, SD) and Number DNNs. Tcl Parameter: UpfInfoNum Identification of a Network Slice is done via the Single Network Slice Selection Assistance Information (S-NSSAI). The NSSAI (Network Slice Selection Assistance Information) is a collection of S-NSSAIs.
|
NF Consumer NEF-AMF , (Additional data fields for NEF (Nnef) - To AMF (N51))
| Event Explore Settings |
Enter the Event Explore Setting for Any UE, Group UE, or Single UE. Available when NEF (Nnef) and To AMF (N51) are enabled on the Service Based Node Emulator Configuration. Get AMF Information From UDM - Available when NEF (Nnef) and To UDM (N52) and at least one of "Any UE"/"Group UE"/"Single UE" is checked and either NRF Interface or NF Instance IDs for AMF SUT is enabled. Select to get AMF information from UDM. NEF will utilize Nudm_UECM_Get service (N52) to get AMF information "Get AMF Infomation From UDM" is checked, then NEF will query NRF or search local SUT info to determine AMF addresses, then start the subscription procedure through N51 interface. Select 3GPP Access or Non 3GPP Access and select to enter Supported Features. Enter 1 to 8 Hex characters. Default : 1f Tcl Parameter: N51NamfGetAmfInfoFromUdmEn Tcl Parameter: N51NamfGetAmfInfoAccessType Tcl Parameter: N51NamfGetAmfSuppFeatEn Tcl Parameter: N51NamfGetAmfSuppFeat
|
NF Consumer NEF-AMF (Additional data fields for NEF (Nnef) - To AMF (N51)) - Subscribe Events Settings (Pop-up Panel)
|
Available on the NEF-AMF Tab when Subscribe Events Settings or Updated Events Settings are selected on the NF Consumer Tab (NEF-AMF). Describes the events to be subscribed for this subscription. Select Report Types and/or Immediate Flag (per report type). Select Immediate Flag to indicate if an immediate event report in the subscription response is requested. The report contains the current value / status of the event stored at the time of the subscription in the AMF. Time Zone Report , Registration State Report , Reachability Report, Access Type Report , Connectivity State Report , Communication Failure Report , Subscription ID Change, Subscription ID Addition, Loss of Connectivity and Location Report. For Availability After DNN Failure, select Immediate Flag, Report UE Reachable, # of Traffic Descriptors, DNN, SD, SST, # of DDD Traffic Descriptors (IPV4 Addr, IPV6 Addr, MAC Addr, PORT) For Location Report, select Location Filter : TAI, CELL ID, N3IWF, UE IP, UDP PORT
Presence IN AOI Report
Include LADN Info - Select to include the Local Area Data Network (LADN) information. Available to enabled when Include Presence Info is not selected. Enter LADN. Select to Include Presence State. Options : IN_AREA, OUT_OF_AREA, UNKNOWN, INACTIVE Tcl Parameter: N51NamfAnySubPreInAOIRptAreasLadnInfoEn_1 Tcl Parameter: N51NamfGroupSubPreInAOIRptAreasLadnInfoEn_1 Tcl Parameter: N51NamfSingleSubPreInAOIRptAreasLadnInfoEn_1 Tcl Parameter: N51NamfAnyUpdatedPreInAOIRptAreasLadnInfoEn_1 Tcl Parameter: N51NamfGroupUpdatedPreInAOIRptAreasLadnInfoEn_1 Tcl Parameter: N51NamfSingleUpdatedPreInAOIRptAreasLadnInfoEn_1
Tcl Parameter: N51NamfAnySubPreInAOIRptAreasLadn_1 Tcl Parameter: N51NamfGroupSubPreInAOIRptAreasLadn_1 Tcl Parameter: N51NamfSingleSubPreInAOIRptAreasLadn_1 Tcl Parameter: N51NamfAnyUpdatedPreInAOIRptAreasLadn_1 Tcl Parameter: N51NamfGroupUpdatedPreInAOIRptAreasLadn_1 Tcl Parameter: N51NamfSingleUpdatedPreInAOIRptAreasLadn_1
Tcl Parameter: N51NamfAnySubPreInAOIRptAreasLadnPreStateEn_1 Tcl Parameter: N51NamfGroupSubPreInAOIRptAreasLadnPreStateEn_1 Tcl Parameter: N51NamfSingleSubPreInAOIRptAreasLadnPreStateEn_1 Tcl Parameter: N51NamfAnyUpdatedPreInAOIRptAreasLadnPreStateEn_1 Tcl Parameter: N51NamfGroupUpdatedPreInAOIRptAreasLadnPreStateEn_1 Tcl Parameter: N51NamfSingleUpdatedPreInAOIRptAreasLadnPreStateEn_1
Tcl Parameter: N51NamfAnySubPreInAOIRptAreasLadnPreState_1 Tcl Parameter: N51NamfGroupSubPreInAOIRptAreasLadnPreState_1 Tcl Parameter: N51NamfSingleSubPreInAOIRptAreasLadnPreState_1 Tcl Parameter: N51NamfAnyUpdatedPreInAOIRptAreasLadnPreState_1 Tcl Parameter: N51NamfGroupUpdatedPreInAOIRptAreasLadnPreState_1 Tcl Parameter: N51NamfSingleUpdatedPreInAOIRptAreasLadnPreState_1
UEs In Area Report
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
|
NF Consumer NEF-SMF , (Additional data fields for NEF (Nnef) - To SMF (N29))
| Event Explore Settings |
Enter the Event Explore Setting for Any UE, Group UE, or Single UE. Available when NEF (Nnef) and To SMF (N29) are enabled on the Service Based Node Emulator Configuration. Get SMF Information From UDM - Available when NEF (Nnef) and To UDM (N52) and at least one of "Any UE"/"Group UE"/"Single UE" is checked and either NRF Interface or NF Instance IDs for SMF SUT is enabled. Select to get SMF information from UDM. NEF will utilize Nudm_UECM_Get service (N52) to get SMF information when "Get SMF Infomation From UDM" is checked, then NEF will query NRF or search local SUT info to determine SMF addresses, then start the subscription procedure through N29 interface. Single NSSAI - Available when Set SMF Information from USM is enabled. Select to enter SST - Range 1 to 255, default :0 and SD - enter 0 to 6 characters. Select to enter DNN. Enter up to 63 characters. Available when Set SMF Information from USM is enabled. Select to enter Supported Features. Enter 1 to 8 Hex characters. Default : 1f Available when Set SMF Information from USM is enabled. Tcl Parameter: N29NsmfGetSmfInfoFromUdmEn Tcl Parameter: N291NsmfSingleNssaiEn Tcl Parameter: N291NsmfSingleNssaiSst Tcl Parameter: N291NsmfSingleNssaiSd Tcl Parameter: N291NsmfDnn Tcl Parameter: N29NsmfSuppFeatEn Tcl Parameter: N29NsmfSuppFeat
Subscribe Events Settings for NEF (Nnef) To SMF (N29) - Pop up Panel
|
NF Consumer NEF-UDM , (Additional data fields for NEF (Nnef) - To UDM (N52))
| Retrieve SMSF Information 3GPP Access Non 3GPP Access |
Available when NEF (Nnef) - To UDM (N52) and To SMS-SC (T4) are enabled on Service Based Node test case. Select Retrieve SMSF Information from 3GPP Access (default) or Non 3GPP Access. Tcl Parameter: N52NudmRetSmsfInfoAccType |
||||||||||||||||||||||||||||||||||||||||||||
| Event Explore Settings |
Enter the Event Explore Setting for Any UE, Group UE, or Single UE. Available when NEF (Nnef) and To UDM (N52) are enabled on the Service Based Node Emulator Configuration.
NF Consumer NEF-UDM (Additional data fields for NEF (Nnef) - To UDM (N52)) - Subscribe Events Settings (Pop-up Panel) Available on the NEF-UDM Tab when Subscribe Events Settings or Updated Events Settings are selected on the NF Consumer Tab (NEF-UDM). Describes the events to be subscribed for this subscription. Select UE Reachability for SMS, CN Type Change, Roaming Status, UE Connection Management State (when version >=16.6.0/Dec2020), Change of SUPI PEI Association and/or Immediate Flag (per report type). Select Immediate Flag to indicate if an immediate event report in the subscription response is requested. For Change of SUPI PEI Association, select to Include Association Type : IMEI_CHANGE, IMEISV_CHANGE
|
||||||||||||||||||||||||||||||||||||||||||||
| NIDD Authorization |
Select to enable NIDD Notification. Available when Nudm Version >= 16.7.0/Mar2021. When enabled enter the DNN. Enter up to 63 characters. Default : dnn1 Enter the SST. Range : 0 to 255. Default : 0 Select to enter the SD. Range : 1 to 6 hex characters. Default : 0 Select Override AF Supplied MTC Information and enter the MTC Provider Information. Default : 1 Tcl Parameter: N52NudmNiddAuEn Tcl Parameter: N52NudmNiddAuDnn Tcl Parameter: N52NudmNiddAuSst Tcl Parameter: N52NudmNiddAuSdEn Tcl Parameter: N52NudmNiddAuSd Tcl Parameter: N52NudmNiddAuOverMtcInfoEn Tcl Parameter: N52NudmNiddAuOverMtcInfo |
NF Producer Namf, Nsmf, Nudm (Additional data fields for Test NEF (Nnef) - Emulate AMF (N51) , Emulate SMF (N29), Emulate UDM (N52) )
| Event Explore Settings |
Enter the Event Explore Setting for Any UE, Group UE, or Single UE. Available when Test NEF (Nnef) and Emulate AMF (N51) or when Test NEF (Nnef) and Emulate SMF (N29) or when Test NEF (Nnef) and Emulate UDM (N52) or Test SMSF (Nsmsf) and From AMF (N20) are enabled on the Service Based Nodal Test Configuration. Notification Settings:
Immediately notification supported UE per AMF Node. Available in Namf Tab when Emulate AMF (N51) is enabled on the Service Based Nodal test case. Range: 1 to 32 Default : 1 Tcl Parameter: NamfImmeNtfUePerNode
Number of UEs that can be notified Immediately by each AMF Node. Available in Nsmf Tab when Emulate SMF (N29) is enabled on the Service Based Nodal test case. Available in Nudm Tab when Emulate UDM (N52) is enabled on the Service Based Nodal test case. Range: 1 to 32 Default : 1 Tcl Parameter: NsmfImmeNtfUePerNode Tcl Parameter: NudmImmeNtfUePerNode
Optional Events Configurations for Namf when Emulate AMF (N51) is enabled on the Service Based Nodal test case. Time Zone Report , Registration State Report , Connectivity State Report , Access Type Report , Reachability Report , Communication Failure Report , Location Report, Presence in AOI Report, UEs in Area Report, 5GS User State Report , Availability after dnn failure, Type Allocation Code Report, Frequent Mobility Registration Report , Loss of Connectivity
Optional Events Configurations for Namf when Emulate AMF (N51) is enabled on the Service Based Nodal test case.
Include LADN Info - Select to include the Local Area Data Network (LADN) information. Available to enabled when Include Presence Info is not selected. Enter LADN. Select to Include Presence State. Options : IN_AREA, OUT_OF_AREA, UNKNOWN, INACTIVE Tcl Parameter: NamfPreInAOIRptItemLadnInfoEn_1_1 Tcl Parameter: NamfPreInAOIRptItemLADN_1_1 Tcl Parameter: NamfPreInAOIRptItemLadnPreStateEn_1_1 Tcl Parameter: NamfPreInAOIRptItemLadnPreState_1_1
Optional Events Configurations for Nsmf when Emulate SMF (N29) is enabled on the Service Based Nodal test case. Per 3GPP TS 29.508 V15.4. Access Types Change, PLMN Change, UE IP Address Change, Communication Failure Report, PDU Session Establishment ,PDU Session Release , UP Path Change, Downlink Data Delivery Status, Communication Failure, PDU Session Establishment , QFI Allocation, QoS Monitoring
Optional Events Configurations for Nudm when Emulate UDM (N52) is enabled on the Service Based Nodal test case. Per 3GPP TS 23.502 Release 16 Change of SUPI PEI Association , UE Reachability for SMS, Roaming Status Change, CN Type Change, UE Connection Management State
|
NF Producer pSEPP N32-c / NF Consumer cSEPP N32-c
Available when SEPP is enabled on Service Based Node test case.
| SEPP Version (29.573) |
Select the SEPP (Security and Edge Protection Proxy) Version (29.573). Available when SEPP is enabled on Service Based Node test case. Options: 16.5.0/Dec2020 (default) Tcl Parameter: CseppN32cSbiVersion Tcl Parameter: PseppN32cSbiVersion |
||||||
| API Prefix |
Select to enter the API Prefix for pSEPP n32c. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: PseppN32cApiPrefixEn Tcl Parameter: PseppN32cApiPrefix |
||||||
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: CseppN32cDefaultHostFormat Tcl Parameter: PseppN32cDefaultHostFormat |
||||||
| Supported Security Capabilities |
Select the Supported Security Capabilities. Multiple values can be selected. Options : TLS, PRINS Default : PRINS Tcl Parameter: PseppN32cSecCap_1 Tcl Parameter: PseppN32cSecCap_2 |
||||||
| JWE Cipher Suite List |
Select the JWE Cipher Suite List. Multiple values can be selected. This option panel is configurable only when "PRINS" is selected in Supported Security Capabilities. Valid values are as specified in clause 5.1 of IETF RFC 7518. Options : A128CBC-HS256, A192CBC-HS384, A256CBC-HS512, A128GCM, A192GCM, A256GCM Default : A128CBC-HS256 Tcl Parameter: PseppN32cJweCipherSuite_1 Tcl Parameter: PseppN32cJweCipherSuite_2 Tcl Parameter: PseppN32cJweCipherSuite_3 Tcl Parameter: PseppN32cJweCipherSuite_4 Tcl Parameter: PseppN32cJweCipherSuite_5 Tcl Parameter: PseppN32cJweCipherSuite_6 |
||||||
| JWS Cipher Suite List |
Select the JWS Cipher Suite List. Multiple values can be selected. This option panel is configurable only when "PRINS" is selected in Supported Security Capabilities and when IPX Security Information is enabled.
Valid values are as specified in clause 3.1 of IETF RFC 7518. Options :HS256, HS384, HS512, RS256, RS384, RS512, ES256, ES384, ES512, PS256, PS384, PS512, none Default : HS256 Tcl Parameter: PseppN32cJwsCipherSuite_1 Tcl Parameter: PseppN32cJwsCipherSuite_2 Tcl Parameter: PseppN32cJwsCipherSuite_3 Tcl Parameter: PseppN32cJwsCipherSuite_4 Tcl Parameter: PseppN32cJwsCipherSuite_5 Tcl Parameter: PseppN32cJwsCipherSuite_6 Tcl Parameter: PseppN32cJwsCipherSuite_7 Tcl Parameter: PseppN32cJwsCipherSuite_8 Tcl Parameter: PseppN32cJwsCipherSuite_9 Tcl Parameter: PseppN32cJwsCipherSuite_10 Tcl Parameter: PseppN32cJwsCipherSuite_11 Tcl Parameter: PseppN32cJwsCipherSuite_12 Tcl Parameter: PseppN32cJwsCipherSuite_13 |
||||||
| PLMN ID List |
Select to configure a PLMN ID list. Enter up to 4 (# of PLMN) For each PLMN enter it's MCC and MNC in the table. Tcl Parameter: PseppN32cPlmnIdListEn Tcl Parameter: PseppN32cPlmnIdNum Tcl Parameter: PseppN32cPlmnId_1 |
||||||
| 3gpp-Sbi-Target-apiRoot Header |
Select to configure 3gPP-sbi-Target-apiRoot Header. Options : True (default), False Tcl Parameter: PseppN32c3gppSbiTgtApiRootHdrEn Tcl Parameter: PseppN32c3gppSbiTgtApiRootHdr |
||||||
| Protection Policy |
Select to enter the Protection Policy information. Select to Verify Peer Protection Policy. This option panel is configurable only when "PRINS" is selected in Supported Security Capabilities. Enter up to 16 API IE Mapping List. Tcl Parameter: PseppN32cProtPolEn Tcl Parameter: PseppN32cVerifyProtPol Tcl Parameter: PseppN32cApiIeMapNum
|
||||||
| Data Type Encryption Policy |
Select to enter the Data Type Encryption Policy information. This option panel is configurable only when "PRINS" is selected in Supported Security Capabilities. Options : UEID (default), LOCATION, KEY_MATERIAL, AUTHENTICATION_MATERIAL, AUTHORIZATION_TOKEN, OTHER, NONSENSITIVE Enter up to 16 API IE Mapping List. Tcl Parameter: PseppN32cDataTypeEncPolEn Tcl Parameter: PseppN32cDataTypeEncPol_1 Tcl Parameter: PseppN32cDataTypeEncPol_2 Tcl Parameter: PseppN32cDataTypeEncPol_3 Tcl Parameter: PseppN32cDataTypeEncPol_4 Tcl Parameter: PseppN32cDataTypeEncPol_5 Tcl Parameter: PseppN32cDataTypeEncPol_6 Tcl Parameter: PseppN32cDataTypeEncPol_7
|
NF Producer pSEPP N32-f / NF Consumer cSEPP N32-f
Available when SEPP is enabled on Service Based Node test case.
| SEPP Version (29.573) |
Select the SEPP (Security and Edge Protection Proxy) Version (29.573). Available when SEPP is enabled on Service Based Node test case. Options: 16.5.0/Dec2020 (default) Tcl Parameter: CseppN32fSbiVersion Tcl Parameter: PseppN32fSbiVersion |
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: CseppN32fDefaultHostFormat Tcl Parameter: PseppN32fDefaultHostFormat |
| Local IPX |
Select to configure Local IPX in tab pSEPP N32-f. It is configurable if "PRINS" is selected as Supported Security Capabilities in tab pSEPP N32-c→NF Producer. Enter the IPX Provider ID (FQDN which uniquely identifies the IPX - up to 256 characters) Select Private Key File - Installed File or a Test Data File. Select to Specify JWS Cipher Suite . per Spec 3GPP TS 33.517 Options: RS256 , RS384, RS512, ES256 (default), ES384, ES512, PS256 Tcl Parameter: PseppN32fIpxIdEn Tcl Parameter: PseppN32fIpxId Tcl Parameter: PseppN32fTestDataFileEn Tcl Parameter: PseppN32fFile Tcl Parameter: PseppN32fJwsCipherSuiteEn Tcl Parameter: PseppN32fJwsCipherSuite |
NF Consumer NF-SEPP
Available when Roaming Scenario with SEPP is enabled on Service Based Nodal Test Cnfg / Service Based Node and SMF Node Emulator Configuration and AMF Node Emulator Configuration test cases.
| SEPP Version (29.573) |
Select the SEPP (Security and Edge Protection Proxy) Version (29.573). Available when Roaming Scenario with SEPP is enabled on Service Based Nodal Test Cnfg / Service Based Node and SMF Node Emulator Configuration and AMF Node Emulator Configuration test cases. Options: 16.5.0/Dec2020 (default) Tcl Parameter: Nf2SeppClnSbiVersion |
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: Nf2SeppDefaultHostFormat |
| Target NF Authority Option |
Select the Target NF Authority option. Options : Telescopic FQDN, 3gpp-Sbi-Target-apiRoot Header Tcl Parameter: Nf2SeppClnTgtNfAuthOpt |
NF Producer SEPP
Available when SEPP is enabled on Service Based Node test case.
| SEPP Version (29.573) |
Select the SEPP (Security and Edge Protection Proxy) Version (29.573). Available when SEPP is enabled on Service Based Node test case. Options: 16.5.0/Dec2020 (default) Tcl Parameter: SeppSrvSbiVersion |
| API Prefix |
Select to enter the API Prefix for SEPP Srv. Select the Auto-Increment Format Wizard to Auto increment the API Prefix.
Tcl Parameter: SeppSrvApiPrefixEn Tcl Parameter: SeppSrvApiPrefix |
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: SeppSrvDefaultHostFormat |
| Unique Delimeter for Converting FQDN to Telescopic Label |
Enter Unique Delimiter for Converting FQDN to Telescopic Label. This delimiter is used to replace period in foreign FQDN to generate telescopic FQDN. It should not appear in the original FQDN. Available in Service Based Node test case on SEPP Tab. Enter 1 to 4 characters. Tcl Parameter: SeppSrvDelFqdn |
| Target NF Authority Option |
Select the Target NF Authority option. Options : Telescopic FQDN, 3gpp-Sbi-Target-apiRoot Header Tcl Parameter: SeppSrvTgtNfAuthOpt |
NF Consumer SEPP-NF
Available when Roaming Scenario with SEPP and SEPP is enabled on Service Based Node test case.
| Number of NFs |
Enter number of NFs. It represents the SEPP client towards the NFs in the same PLMN. Available when Roaming Scenario with SEPP and SEPP is enabled on Service Based Node test case. Range : 1 to 50 Default : 1 Tcl Parameter: Sepp2NfNumNfs |
NF Producer PFD (Packet Flow Description) Data and NIDD for Configuration (Nnef - 29.551)
| PFD Data Settings |
Select to enable up to 10 Packet Flow Description (PFD) data configuration panes. Tcl Parameter: NnefPfdDataSettings |
||||
| Subscriptions Per UE |
Enter up to 10 subscriptions per UE for PFD. Tcl Parameter: NnefPfdDataSubsPerUeNum |
||||
|
Select the number of PFD (Packet Flow Description) Data for Configuration. Range : 1 to 10 Tcl Parameter: NnefPfdDataPfdNum |
|||||
|
Enter the Application ID for PFD Data Configuration. See 3GPP TS 29.571 [7] for formatting of ApplicationID. Tcl Parameter: NnefPfdDataAppId_1 |
|||||
|
Select to enter the PFD Data Caching Time in milliseconds. Range : 0 to 4294967295 Tcl Parameter: NnefPfdDataCachingTimeEn_1 Tcl Parameter: NnefPfdDataCachingTime_1 |
|||||
|
Select to enter the number of PFD Content. Options : 1, 2 Enter PFD ID. Up to 180 characters. Tcl Parameter: NnefPfdDataPfdConNum_1 Tcl Parameter: NnefPfdDataPfdConPfdId_1_1 |
|||||
|
Select to enter the number of PFD URLs. Options : 0, 1, 2 Enter up to 128 characters. Default : http://www.3gpp.org/ftp/Specs Enter URL. Tcl Parameter: NnefPfdDataPfdConUrlEn_1_1 Tcl Parameter: NnefPfdDataPfdConUrlNum_1_1 Tcl Parameter: NnefPfdDataPfdConUrl_1_1_1 |
|||||
|
Select to enter the number of PFD Flow Descriptions. Options : 0, 1, 2 Enter FLow Description. Tcl Parameter: NnefPfdDataPfdConFlowDescEn_1_1 Tcl Parameter: NnefPfdDataPfdConFlowDescNum_1_1 Tcl Parameter: NnefPfdDataPfdConFlowDesc_1_1_1 |
|||||
|
Select to enter the number of Domain Names. Options : 0, 1, 2 Enter Domain Name. Tcl Parameter: NnefPfdDataPfdConDomainNameEn_1_1 Tcl Parameter: NnefPfdDataPfdConDomainNameNum_1_1 Tcl Parameter: NnefPfdDataPfdConDomainName_1_1_1 |
|||||
|
Select the Domain Name Protocol. Options : DNS_QNAME TLS_SNI TLS_SAN TLS_SCN Tcl Parameter: NnefPfdDataPfdConProtocolEn_1_1 Tcl Parameter: NnefPfdDataPfdConProtocol_1_1 |
|||||
|
Select to enter the Notify Interval Setting for PFD in milliseconds. Range : 0 to 1000000 Default : 100 Tcl Parameter: NnefPfdDataNtfTimerSettingEn Tcl Parameter: NnefPfdDataNtfTimerSetting |
|||||
|
Number of PFD Data for Notifications
# of PFD Notification
Application ID
Removal of PFDs
Partial Update of PFDs |
Available when Notify Interval Setting is enabled. Enter up to 3 PFD Data for Notifications. Options : 1, 2, 3 Select the # of PFD Notification. Range : 1 to 5 Enter the Application ID for PFD Data Notification. See 3GPP TS 29.571 [7] for formatting of ApplicationID. Select to indicate Removal of PFDs. Select to indicate Partial Update of PFDs.
Tcl Parameter: NnefPfdDataPfdNtfctnNum Tcl Parameter: NnefPfdDataPfdNtfctnNum_1 Tcl Parameter: NnefPfdDataPfdNtfAppId_1_1 Tcl Parameter: NnefPfdDataPfdNtfRemvEn_1_1 Tcl Parameter: NnefPfdDataPfdNtfPartEn_1_1 |
||||
|
Number of PDU Sessions
|
Available on Service Based Nodal under SMF-NEF when (Test NEF (Nnef) and Emulate SMF (N29)) and Nnef Version >= 16.7.0/Sept2020. Select up to 11 Number of PDU Sessions for NIDD ( Non-IP Data Delivery) . NIDD API (Spec 23.502 4.25 Procedures for NEF based Non-IP Data Delivery). Enable NIDD for DNN Pane to become available.
Tcl Parameter: N29NnefNiddPduSessionsNums Tcl Parameter: N29NnefNiddEn
DNN (1 to 11)
|
||||
|
Number of Application IDs List
Number of Subscriptions IDs
Application ID and Update Application ID. |
Available on Service Based Nodal under SMF-NEF when (Test NEF (Nnef) and Emulate SMF (N29)) and Nnef Version >= 16.6.0/Dec2020. Select up to 20 Number of Application IDs Lists and enter the Application ID. Select up to 3 Number of Subscriptions IDs Lists. Select up to 10 Application ID Index and Update Application ID Index. Select and enter the index in the application id list. Tcl Parameter: N29NnefPfdAppIdListNum Tcl Parameter: N29NnefPfdAppIdList_1 Tcl Parameter: N29NnefPfdSubNum Tcl Parameter: N29NnefPfdAppIdNum_1 Tcl Parameter: N29NnefPfdAppId_1_1 Tcl Parameter: N29NnefPfdAppIdUpdNum_1 Tcl Parameter: N29NnefPfdAppIdUpd_1_1 |
||||
|
Select to enter the Supported Features for PFD Management Transaction Notification Settings. Available on Service Based Node under Nnef when (NEF (Nnef) and To UDR (N37) ) and Nnef Version >= 16.6.0/Dec2020. Range : 1 to 8 HEX characters Default : 1f Tcl Parameter: NnefSupFeatEn Tcl Parameter: NnefSupFeat |
|||||
| PFD Management Transaction Notification Settings |
Select to enter the PFD Management Transaction Notification Settings details. Available on Service Based Node under Nnef when (NEF (Nnef) and To UDR (N37) ) and Nnef Version >= 16.6.0/Dec2020. Tcl Parameter: NnefPfdTranNtfEn |
||||
|
Select to enter the Notify Interval Setting for PFD Management Transaction Notification in milliseconds. Available on Service Based Node under Nnef when (NEF (Nnef) and To UDR (N37) ) and Nnef Version >= 16.6.0/Dec2020. Range : 0 to 1000000 Default : 100 Tcl Parameter: NnefPfdTranNtfTimerSettingEn Tcl Parameter: NnefPfdTranNtfTimerSetting |
|||||
| Number of Transaction Notifications |
Select to enter the Number of Transaction Notifications for PFD Management Transaction Notification Settings details. Available on Service Based Node under Nnef when (NEF (Nnef) and To UDR (N37) ) and Nnef Version >= 16.6.0/Dec2020. Range : 1 to 3 Default : 1 Tcl Parameter: NnefPfdTranNtfNum |
||||
|
Original / Update External App ID Caching Time (s) Failure Code
|
Select to enter the Number of Reporters for PFD Management Transaction Notification Settings details. Available on Service Based Node under Nnef when (NEF (Nnef) and To UDR (N37) ) and Nnef Version >= 16.6.0/Dec2020. For each reporter, an Original and an Update pane becomes available to enter the External App Id, Caching Time (s) and Failure Code. Range : 1 to 5 Default : 1 Tcl Parameter: NnefPfdTranReptrNum_1 Select the Original or Update Pane. Select the number of External Application Id's and enter the External Application Id (app id 1) in the table. Range : 1 to 3, default : 1 Tcl Parameter: NnefPfdTranExtAppIdNum_1_1_0 Tcl Parameter: NnefPfdTranExtAppIdNum_1_1_1 Tcl Parameter: NnefPfdTranExtAppId_1_1_0_1 Tcl Parameter: NnefPfdTranExtAppId_1_1_1_1
Select to enter the Caching Time (s) for PFD Management Transaction Notification Settings in seconds. Range : 0 to 4294967295, default : 0 Tcl Parameter: NnefPfdTranCachingTimeEn_1_1_0 Tcl Parameter: NnefPfdTranCachingTimeEn_1_1_1 Tcl Parameter: NnefPfdTranCachingTime_1_1_0_1 Tcl Parameter: NnefPfdTranCachingTime_1_1_1_1
Select the Failure Code. Options : MALFUNCTION , RESOURCE_LIMITATION, Tcl Parameter: NnefPfdTranFailCode_1_1_0 Tcl Parameter: NnefPfdTranFailCode_1_1_1 |
||||
| NIDD External Group Delivery Rate (Request/s) |
Available on Service Based Node under Nnef when (NEF (Nnef) is enabled and Nnef Version >= 16.6.0/Dec2020. Select to enter the NIDD Group External Group Delivery Rate request in seconds. Range : 0.001 to 3000.0 Default : 1.0 Tcl Parameter: NnefNiddExtGrpRate |
||||
| External Group ID Setting |
Available on Service Based Node under Nnef when (NEF (Nnef) is enabled and Nnef Version >= 16.6.0/Dec2020. Select to enter the External Group ID Setting. Select up to 10 Group Numbers. Range : 0 to 10 Default : 0 Enter Starting UE Index, Ending UE Index and Group Identity. Starting UE Index must less than Ending UE Index, Group Identity should following format as (extgroupid-[^@]+@[^@]+) Default : [email protected] Tcl Parameter: NnefGrpIdNum Tcl Parameter: NnefGrpId_1 |
||||
| AF List |
Available on Service Based Node under Nnef when (NEF (Nnef) is enabled and Nnef Version >= 16.6.0/Dec2020 and NEF Interworking is enabled. Select up to 50 AF Lists. Enter the SCS/AS ID and Destination URI for each AF List. Range : 0 to 10 Default : 0 SCS/AS ID - Enter 1 to 64 characters. . Default : spirent-af-1 Destination URI - Enter up to 128 string, must start with http:// or https://. Default : http://10.202.1.1/ntf-service/v1/nnef-cfg-trig-ntf Tcl Parameter: NnefAfListNum Tcl Parameter: NnefAfListId_1 |
||||
| NIDD Notification Settings |
Available on Service Based Node under Nnef when (NEF (Nnef) is enabled and Nnef Version >= 16.6.0/Dec2020. Select to enable NIDD Notification Settings. When enabled, enter the Notify Interval Setting (ms) in milliseconds. Range : 100 to 4294967295 Default : 100 Select up to 3 Number of NIDD Notification. Range : 1 to 3, default : 1 A Notification panel with Original and Update parameters is available for input. Select Uplink Data Notification to select Reliable Data Service (Delivered Data) and RDS Port (UE Port and NEF Port). Enter Delivered Data - Range 1 to 2048 characters, default : 0 Enter UE Port and NEF Port - Range : 0 to 65535 , default : 0 Select NIDD Configuration Status Notification to select RDS Capability Indication (Status) and RDS Port (UE Port and NEF Port). Select the RDS Capability Indication Status. Options : ACTIVE, , TERMINATED_UE_NOT_AUTHORIZED, TERMINATED, RDS_PORT_UNKNOWN Enter UE Port and NEF Port - Range : 0 to 65535 , default : 0 Select Downlink Data Delivery Status Notification and select to enter the Requested Transmission Time in seconds and the Delivery Status. Enter the Requested Transmission Time in seconds. Range : 1 to 4294967295 Default : 10 Select the Delivery Status. Options : SUCCESS (defualt) , SUCCESS_NEXT_HOP_ACKNOWLEDGED , SUCCESS_NEXT_HOP_UNACKNOWLEDGED , SUCCESS_ACKNOWLEDGED, Select Gmd NIDD Downlink Data Delivery Status Notification and select to enter the Requested Transmission Time in seconds and the Delivery Status. Enter the Requested Transmission Time in seconds. Range : 1 to 4294967295 Default : 10 Select the Delivery Status. Options : SUCCESS (defualt) , SUCCESS_NEXT_HOP_ACKNOWLEDGED , SUCCESS_NEXT_HOP_UNACKNOWLEDGED , SUCCESS_ACKNOWLEDGED, Select Manage Port and enter up to 3 Manage Ports. For each manage Port, enter Application ID (default = app id 1) , enable Skip UE Inquiry and select the Manage Entity ( UE or AS). Tcl Parameter: NnefNiddNtfSetEn Tcl Parameter: NnefNiddNtfIntervalEn Tcl Parameter: NnefNiddNtfInterval Tcl Parameter: NnefNiddNtfNum Tcl Parameter: NnefNiddOrgUlDataNtfEn_1 Tcl Parameter: NnefNiddOrgUlDataNtfRds_1 Tcl Parameter: NnefNiddOrgUlDataNtfData_1 Tcl Parameter: NnefNiddOrgUlDataNtfRdsPortEn_1 Tcl Parameter: NnefNiddOrgUlDataNtfRdsPortUePort_1 Tcl Parameter: NnefNiddOrgUlDataNtfRdsPortNefPort_1 Tcl Parameter: NnefNiddOrgCfgStatusNtfEn_1 Tcl Parameter: NnefNiddOrgCfgStatusNtfRdsCapIndEn_1 Tcl Parameter: NnefNiddOrgCfgStatusNtfStatus_1 Tcl Parameter: NnefNiddOrgCfgStatusNtfRdsPortEn_1 Tcl Parameter: NnefNiddOrgCfgStatusNtfRdsPortUePort_1 Tcl Parameter: NnefNiddOrgCfgStatusNtfRdsPortNefPort_1 Tcl Parameter: NnefNiddOrgDlDataStatusNtfEn_1 Tcl Parameter: NnefNiddOrgDlDataStatusNtfReqRetrTimeEn_1 Tcl Parameter: NnefNiddOrgDlDataStatusNtfReqRetrTime_1 Tcl Parameter: NnefNiddOrgDlDataStatusNtfStatus_1 Tcl Parameter: NnefNiddOrgGmdDlDataStatusNtfEn_1 Tcl Parameter: NnefNiddOrgGmdDlDataStatusNtfReqRetrTimeEn_1 Tcl Parameter: NnefNiddOrgGmdDlDataStatusNtfReqRetrTime_1 Tcl Parameter: NnefNiddOrgGmdDlDataStatusNtfStatus_1 Tcl Parameter: NnefNiddOrgManagePortNtfEn_1 Tcl Parameter: NnefNiddOrgManagePortNtfNum_1 Tcl Parameter: NnefNiddOrgManagePortNtfAppId_1_1 Tcl Parameter: NnefNiddOrgManagePortNtfSkipUe_1_1 Tcl Parameter: NnefNiddOrgManagePortNtfEntityEn_1_1 Tcl Parameter: NnefNiddOrgManagePortNtfEntity_1_1 Tcl Parameter: NnefNiddUpdUlDataNtfEn_1 Tcl Parameter: NnefNiddUpdUlDataNtfRds_1 Tcl Parameter: NnefNiddUpdUlDataNtfData_1 Tcl Parameter: NnefNiddUpdUlDataNtfRdsPortEn_1 Tcl Parameter: NnefNiddUpdUlDataNtfRdsPortUePort_1 Tcl Parameter: NnefNiddUpdUlDataNtfRdsPortNefPort_1 Tcl Parameter: NnefNiddUpdCfgStatusNtfEn_1 Tcl Parameter: NnefNiddUpdCfgStatusNtfRdsCapIndEn_1 Tcl Parameter: NnefNiddUpdCfgStatusNtfStatus_1 Tcl Parameter: NnefNiddUpdCfgStatusNtfRdsPortEn_1 Tcl Parameter: NnefNiddUpdCfgStatusNtfRdsPortUePort_1 Tcl Parameter: NnefNiddUpdCfgStatusNtfRdsPortNefPort_1 Tcl Parameter: NnefNiddUpdDlDataStatusNtfEn_1 Tcl Parameter: NnefNiddUpdDlDataStatusNtfReqRetrTimeEn_1 Tcl Parameter: NnefNiddUpdDlDataStatusNtfReqRetrTime_1 Tcl Parameter: NnefNiddUpdDlDataStatusNtfStatus_1 Tcl Parameter: NnefNiddUpdGmdDlDataStatusNtfEn_1 Tcl Parameter: NnefNiddUpdGmdDlDataStatusNtfReqRetrTimeEn_1 Tcl Parameter: NnefNiddUpdGmdDlDataStatusNtfReqRetrTime_1 Tcl Parameter: NnefNiddUpdGmdDlDataStatusNtfStatus_1 Tcl Parameter: NnefNiddUpdManagePortNtfEn_1 Tcl Parameter: NnefNiddUpdManagePortNtfNum_1 Tcl Parameter: NnefNiddUpdManagePortNtfAppId_1_1 Tcl Parameter: NnefNiddUpdManagePortNtfSkipUe_1_1 Tcl Parameter: NnefNiddUpdManagePortNtfEntityEn_1_1 Tcl Parameter: NnefNiddUpdManagePortNtfEntity_1_1 |