The Nudm NF (Network Function) Producer tab is used in the Service Based Node test case and HSS Node Emulator Cnfg when Emulate UDM (Nudm) is enabled. Also available in the Service Based Nodal test case when Test UDR (Nudr) and From UDM (N35) or when Test NEF (Nnef) and Emulate UDM (N52) are enabled.
Per 3GPP TS 23.501, 23.502 and 29.5xx.
NOTE: As of Release 17.6, significant changes were made to this tab in support of the September / December 5G releases. Your previous test cases will go red and will require updates. |
Measurements collected are reported on the UDM Producer report tab.
NF Producer
|
NF Producer
Subscribed Network Slice Selection Assistance Information
|
Access and Mobility Subscription Data |
|
Service Area Restrictions Forbidden Areas
|
|
Session Management Subscription Data
|
Session Management Subscription Data
|
|
|
Enable Trace Data |
Enable Trace Data |
Subscription Concealed Identifier |
AMF 3Gpp Access Registration |
Enable Emergency Info |
SMS Management Subscription Data
|
SMF Registration |
External Group ID Setting
|
Select the Nudm Version. Available when UDM (Nudm) is selected on Service Based Node test case. Options: 15.2.0/Dec2018 (default) , 15.4.0/Jun2019, 16.2.0/Dec2019, 16.6.0/Dec2020, 16.7.0/Mar2021 Tcl Parameter: NudmSbiVersion |
|
Select Validate Access Token to support OAuth2 Authorization for NF Producer. Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1. Enter Secret Key. Options : String or Hex with 0x. Enter up to 32 characters. Default : 0x00 Tcl Parameter: NudmValidateAccTokEn Tcl Parameter: NudmAccTokSecKey |
|
Select to include the Custom Http headers for Origination Timestamp (3gpp-Sbi-Origination-Timestamp). Tcl Parameter: Nudm3gppSbiOrigTimestampEn |
|
Default Host Format in apiRoot IP FQDN |
Select which default host format to use in apiRoot, IP or FQDN (Fully Qualified Domain Name). Default : IP Spec reference : 3GPP 29.501, RFC #3986 Tcl Parameter: NudmDefaultHostFormat |
Default Binding Level |
Enable to select the default binding level. Available when NRF Interface is enabled on the Service Based Node test case. Options : NF Set, NF Instance (default) NF Set can be selected only when "NF Set ID" is enabled on UDM SBI Node under Network Devices. Tcl Parameter: NudmDefBindLevelEn Tcl Parameter: NudmDefBindLevel |
Select which authentication Algorithm to use. Available in Service Based Node when UDM (Nudm) is selected and in Service Based Nodal when Test AUSF (Nausf),Emulate UDM N13) or when Test NEF (Nnef) and Emulate UDM (N52) are selected. You can only select one or the other, or both (5G AKA, EAP) in Service Based Nodal. You can only select one or the other, not both (5G AKA, EAP) in Service Based Node. 5G AKA or EAP are supported. If 5G AKA is selected, the 5G AKA Pane becomes available for input. If EAP is selected, the EAP Settings box becomes available to select. Currently only EAP-AKA' is supported. Tcl Parameter: NudmAlgorithm |
Allows you to configure the SUPI (Subscription Permanent Identifier)
Use SUCI |
Select to use SUCI de-concealment. UDM performs de-concealment to retrieve SUPI from SUCI, if SUCI is included in the request. Note: SUPI de-concealment from SUCI is described in flow below. Available on Service Based Node when UDM (Nudm) is selected. Tcl Parameter: NudmSuciEn |
Select the Protection Scheme. Available on Service Based Node when UDM (Nudm) is selected. Option: Null-Scheme, Profile <A>, Profile <B> Tcl Parameter: NudmProtectionScheme |
|
MSIN ASCII Encoding |
Select for MSIN ASCII encoding. Available when Protection Scheme = Profile <A> or Profile <B>. Available on Service Based Node when UDM (Nudm) is selected. Range: 0 to 255 Default: 0 Tcl Parameter: NudmMsinAsciiEn |
Available when Protection Scheme = Profile <A> or Profile <B>. Available on Service Based Node when UDM (Nudm) is selected. How to generate Home Network Key pair: SSH to the Landslide test server or connect to any system that can execute the commands listed below: For Profile <A>:
For Profile <B> :
Range: Hex with 0x, at least 1 byte included for instance : 0x00 Default: 0x00 Tcl Parameter: NudmKhnPrivKey |
Available in Service Based Node when UDM (Nudm) is selected and in Service Based Nodal when Test AUSF (Nausf),Emulate UDM N13) or when Test NEF (Nnef) and Emulate UDM (N52) are enabled.
Algorithm |
Select an Authentication Algorithm for 5G AKA. Additional fields become available for input. Options : Milenage ( Defined in 3GPP TS 35.205) , Test Algorithm ( Defined in 3GPP TS 34.108), TUAK (3GPP TS 35.231) Tcl Parameter: Nudm5gAkaAlg |
||||||||||||||||
Secret Key |
The MS's text or hexadecimal key that is associated with its GUTI and is used to derive the MME/LTE ciphering key. Range: Either String or HEX, If hex must start with 0x Default: 0x00
Tcl Parameter: NudmSecretKey |
||||||||||||||||
RES Length (bytes) |
Per 3GPP (33.102) specified RES Length of 4-16 octets. Per 34.108, for support of 128 bits (16 bytes). Available in Service Based Node when UDM (Nudm) is selected and in Service Based Nodal when Test AUSF (Nausf),Emulate UDM N13) is selected. Range: 4, 8, 16 Default : 8 Tcl Parameter: NudmAuthResLen |
||||||||||||||||
Operator Variant |
The 128-bit, operator-specific MILENAGE constant (OP) provisioned for the network. Range: Up to 16-Byte hex string Default: 0x63BFA50EE6523365FF14C1F45F88737D Tcl Parameter: NudmOpType Tcl Parameter: NudmOpVar |
||||||||||||||||
OPc |
A128-bit value derived from OP and K and used in subsequent computations. Hence, less sensitive and if obtained by third party.
Range: Up to 16-Byte hex string Default: 0x63BFA50EE6523365FF14C1F45F88737D Tcl Parameter: NudmOpC |
||||||||||||||||
TUAK Algorithm |
The following fields become available when Algorithm = TUAK. For information about how the fields are used in the TUAK algorithm the user should refer to the 3GPP TS 35.231 specification.
|
||||||||||||||||
AMF |
Enter up to a 2 byte hex string for the AMF. Range: 2-Byte hex string Default: 0x8000 Tcl Parameter: NudmAmf Tcl Parameter: NudmTuakAmf |
Select the number of Single Network Slice Selection Assistance Information (Nssais). A NSSAI is a collection of smaller components, Session Management NSSAIs (SM-NSSAI), which include a Slice Service Type (SST) and possibly a Slice Differentiator (SD). Slice service type refers to an expected network behavior in terms of features and services (e.g. specialized for broadband or massive IoT), while the slice differentiator can help selecting among several Network Slice instances of the same type, e.g. to isolate traffic related to different services into different slices. Range: 1 to 16 Enter SST (Slice Service Type) and SD (Slice Differentiator) and Default = N or Y. Tcl Parameter: NudmNumSnssais Tcl Parameter: NudmSnssai_1 |
Select "DNN with Starting SUPI Mode via TDF" to allocate the SUPI from the DNN entry in the TDF file. Each Row (Multiplier Label) is a different DNN. SBI Node can support up to 1500 unique DNNs. The SUPI values will be allocated based on the STARTING_SUPI and its range of each DNN entry from this TDF file. The available columns of TDF file is:
STARTING_SUPI shall be numeric, at most 15 digts. SUPI_RANGE shall be numeric, in range 1..2147483647. SM_INDEX shall be numeric, and in range 1..8. DNN_INDEX shall be numeric, and in range 1..16. NSSAI has format as ([0-9][0-9]*)(-)([0-9a-f][0-9a-f])* or ([0-9][0-9])*, the first part is SST which value is from 0 to 255, the second part is SD which value is from 1 to 6 Hex characters, the two parts are combined with '-', and the first part shall be mandatory, the second part can be optional. DNN_NAME contains up to 63 characters, at least one character.
Tcl Parameter: NudmSmDnnSupiCfgFileEn Tcl Parameter: NudmSmDnnSupiCfgFile |
|||||||||||
Enter Number of Session Management Subscriptions. Enter SM Data 1 up to 8. Enter Single Nssai. Note that each SM Data cannot be configured with the same single NSSAI during configuration. A NSSAI is a collection of smaller components, Session Management NSSAIs (SM-NSSAI), which include a Slice Service Type (SST) and possibly a Slice Differentiator (SD). Slice service type refers to an expected network behavior in terms of features and services (e.g. specialized for broadband or massive IoT), while the slice differentiator can help selecting among several Network Slice instances of the same type, e.g. to isolate traffic related to different services into different slices. Enter SST (Slice Service Type) and SD (Slice Differentiator). Tcl Parameter: NudmNumSmSubs Tcl Parameter: NudmSmSnssai_1 |
|||||||||||
Enter up to 16 DNNs (Data Network Name). DNN is equivalent to APN. Tcl Parameter: NudmSmNumDnns_1 |
|||||||||||
Enter DNN Description. Up to 63 characters. Tcl Parameter: NudmSmDnn_1_1 |
|||||||||||
Select to enable the default indicator. Tcl Parameter: NudmSmDnnDefaultIndEn_1_1 |
|||||||||||
Select to enable if LBO Roaming is allowed. Tcl Parameter: NudmSmDnnLboAllowedEn_1_1 |
|||||||||||
Select the default session type and any additional session types below. Options: IPv4 (default ), IPv6, IPv4v6, Unstructured and Ethernet Tcl Parameter: NudmSmDnnDefaultSessionType_1_1 |
|||||||||||
Select additional session types. Options: IPv4v6 (default ), IPv4, IPv6, Unstructured and Ethernet Tcl Parameter: NudmSmDnnSessTypeIpv4v6En_1_1 Tcl Parameter: NudmSmDnnSessTypeIpv4En_1_1 Tcl Parameter: NudmSmDnnSessTypeIpv6En_1_1 Tcl Parameter: NudmSmDnnSessTypeUnstrEn_1_1 Tcl Parameter: NudmSmDnnSessTypeEthEn_1_1 |
|||||||||||
Select Default SSC Mode. Options: SSC_MODE_1, SSC_MODE_2, SSC_MODE_3 Tcl Parameter: NudmSmDnnDefaultSScMode_1_1 |
|||||||||||
Select additional SSC Modes. Options: SSC_MODE_1, SSC_MODE_2, SSC_MODE_3 Tcl Parameter: NudmSmDnnSScMode1En_1_1 Tcl Parameter: NudmSmDnnSScMode2En_1_1 Tcl Parameter: NudmSmDnnSScMode3En_1_1 |
|||||||||||
Select to enable Iwk EPS indicator. Tcl Parameter: NudmSmDnnIwkEpsIndEn_1_1 Tcl Parameter: NudmSmDnnIwkEpsInd_1_1 |
|||||||||||
Select to enable Local Area Data Network (LADN) indicator. Not available when Nudm Version > 15.2.0/Dec2018. Tcl Parameter: NudmSmDnnLadnIndEn_1_1 Tcl Parameter: NudmSmDnnLadnInd_1_1 |
|||||||||||
Select to enable 3GPP Charging Characteristics. Reference: 3GPP 29.503. In release 19.2, the data entry requirements changed from allowing up to 4 Hex characters to requiring 4 Hex characters. Tcl Parameter: NudmSmDnn3gppChargeChEn_1_1 Tcl Parameter: NudmSmDnn3gppChargeCh_1_1 |
|||||||||||
Select to indicate if Up Integrity and Up Confidentiality are Required (default), Preferred or Not Needed. Tcl Parameter: NudmSmDnnUpSecurityEn_1_1 Tcl Parameter: NudmSmDnnUpIntegrity_1_1 Tcl Parameter: NudmSmDnnUpConfidentiality_1_1 |
|||||||||||
Select to enable 5G QoS Profile. Tcl Parameter: NudmSmDnnQosEn_1_1
|
|||||||||||
Select to enable Session AMBR. Select to enter AMBR Uplink and Downlink. Range: 0 to 65535 Default: 1 Range: bps, kbps, Mbps (default), Gbps, Tbps Default: Mbps Tcl Parameter: NudmSmDnnSessAmbrEn_1_1 Tcl Parameter: NudmSmDnnSessAmbrUlRate_1_1 Tcl Parameter: NudmSmDnnSessAmbrDlRate_1_1 Tcl Parameter: NudmSmDnnSessAmbrUlUnit_1_1 Tcl Parameter: NudmSmDnnSessAmbrDlUnit_1_1 |
|||||||||||
V4 Address V6 Address V6 Prefix |
Select to enter a valid V4, V6 Static Address and a valid V6 Prefix for Static IP Addresses. A valid V6 prefix requires '[IPv6 Address] / [Prefix Length]'. Tcl Parameter: NudmSmDnnStaticIpv4En_1_1 Tcl Parameter: NudmSmDnnStaticIpv4_1_1 Tcl Parameter: NudmSmDnnStaticIpv6En_1_1 Tcl Parameter: NudmSmDnnStaticIpv6_1_1 Tcl Parameter: NudmSmDnnStaticIpv6PrefEn_1_1 Tcl Parameter: NudmSmDnnStaticIpv6Pref_1_1 |
SMS Subscribed |
Select SMS Subscribed. Tcl Parameter: NudmSmsSubscribedEn |
Enable Trace Data |
Enable to enter Trace Data. Tcl Parameter: NudmTraceEn |
Trace Depth |
Select the Trace Depth. It defines how detailed information should be recorded in the Network Element. Per 3GPP TS 29.571, table 5.6.3.1-1. Option: Minimum (default), Medium, Maximum, Minimum without vendor specific extension, Medium without vendor specific extension, Maximum without vendor specific extension Tcl Parameter: NudmTraceDepth |
Trace Data Reference |
Enter the Trace Reference information which includes the MCC, MNC and Trace ID. For the Mobile Country code and Mobile Network Code capture up to 3 decimal digits. The default is 000. For the Trace ID, enter up to 6 Hex digits. Tcl Parameter: NudmTraceRef |
List of NE Types |
Enter a list of NE types (Hex Characters). Tcl Parameter: NudmNeTypeList |
Triggering Events |
Enter Triggering Events. Tcl Parameter: NudmEventList |
List of Interfaces |
Select to enter a list of interfaces. (Hex Characters) Tcl Parameter: NudmInterfacesListEn Tcl Parameter: NudmInterfacesList |
IPv4 Address of the Trace Collection Entity |
Select to enter an IPv4 address of the Trace Collection Entity. Tcl Parameter: NudmCollEntityIpv4AddrEn Tcl Parameter: NudmCollEntityIpv4Addr |
IPv6 Address of the Trace Collection Entity |
Select to enter an IPv6 address of the Trace Collection Entity. Tcl Parameter: NudmCollEntityIpv6AddrEn Tcl Parameter: NudmCollEntityIpv6Addr |
Available in the Service Based Nodal test case when Test UDR (Nudr) and From UDM (N35) or when Test NEF (Nnef) and Emulate UDM (N52) are enabled.
AMF Instance ID |
Enter the AMF Instance ID in UUID Version 4 format. Format : UUID version 4: 4hexOctet-2hexOctet-2hexOctet-2hexOctet-6hexOctet Default : f02b01eb-7c94-4013-8387-df9b4fcdc496 Tcl Parameter: NudmAmf3GppAccRegInstId |
RAT Type |
Select the RAT (Radio Access Technology) Type. NR = New Radio, EUTRA = Evolved Universal Terrestrial Radio Access Options: NR (default), EUTRA, WLAN, Virtual Tcl Parameter: NudmAmf3GppAccRegRatType |
PEI |
Select to enter the Permanent Equipment Identifier (PEI). Enter 15 to 16 digits. Tcl Parameter: NudmAmf3GppAccRegPeiEn Tcl Parameter: NudmAmf3GppAccRegPei |
pcscfRestorationCallbackUri |
Select to include pcscfRestorationCallbackUri. Tcl Parameter: NudmAmf3GppAccRegPcscfCbUriEn |
imsVoPS |
Select the imsVoPS type. Options : HOMOGENEOUS_SUPPORT (default), HOMOGENEOUS_NON_SUPPORT, NON_HOMOGENEOUS_OR_UNKNOWN Tcl Parameter: NudmAmf3GppAccRegImsVops |
GUAMI |
Enter the GUAMI (Globally Unique AMF ID) information which includes the MCC, MNC and AMF ID. For the Mobile Country code and Mobile Network Code capture up to 3 decimal digits. The default is 000. For the AMF ID, enter 6 Hex digits. Tcl Parameter: NudmAmf3GppAccRegMcc Tcl Parameter: NudmAmf3GppAccRegMnc Tcl Parameter: NudmAmf3GppAccRegAmfId |
Enable Emergency Info |
Enable to enter Emergency Info Data. Available when Nudm Version > 15.2.0/Dec2018. Tcl Parameter: NudmEmeInfoEn |
Emergency Info Type |
Select the Emergency Info Type. Available when Nudm Version > 15.2.0/Dec2018. Option: Static IP Addresses, FQDN of PGW Tcl Parameter: NudmEmeInfoType |
FQDN of PGW |
Enter the Fully Qualified Domain Name of the PGW. Available when Nudm Version > 15.2.0/Dec2018 and when Emergency Info Type = FQDN of PGW. Enter 1 to 128 valid hostname characters. e.g. server.host.com Tcl Parameter: NudmEmeInfoPgwFqdn |
Static IP Addresses V4 Address |
Select to enter a valid static IPv4 address. Available when Nudm Version > 15.2.0/Dec2018 and when Emergency Info Type = Static IP Addresses. Enter a valid IPv4 address. Tcl Parameter: NudmEmeInfoStaticIpv4En Tcl Parameter: NudmEmeInfoStaticIpv4 |
Static IP Addresses V6 Address |
Select to enter a valid static IPv6 address. Available when Nudm Version > 15.2.0/Dec2018 and when Emergency Info Type = Static IP Addresses. Enter a valid IPv6 address. V6 Address and V6 Prefix are mutually exclusive, can only select one or the other, not both. Tcl Parameter: NudmEmeInfoStaticIpv6En Tcl Parameter: NudmEmeInfoStaticIpv6 |
Static IP Addresses V6 Prefix |
Select to enter a valid static IPv6 prefix. Available when Nudm Version > 15.2.0/Dec2018 and when Emergency Info Type = Static IP Addresses. Enter a valid IPv6 prefix. V6 Address and V6 Prefix are mutually exclusive, can only select one or the other, not both. Tcl Parameter: NudmEmeInfoStaticIpv6PrefEn Tcl Parameter: NudmEmeInfoStaticIpv6Pref |
MT SMS Subscribed |
Select to enable MT SMS Subscribed and select true or false. Tcl Parameter: NudmSmsMngSubDataMtSmsSubEn Tcl Parameter: NudmSmsMngSubDataMtSmsSub |
MT SMS Barring All |
Select to enable MT SMS Barring All and select true or false. Tcl Parameter: NudmSmsMngSubDataMtSmsBarAllEn Tcl Parameter: NudmSmsMngSubDataMtSmsBarAll |
MT SMS Barring Roaming |
Select to enable MT SMS Barring Roaming and select true or false. Tcl Parameter: NudmSmsMngSubDataMtSmsBarRoamEn Tcl Parameter: NudmSmsMngSubDataMtSmsBarRoam |
M0 SMS Subscribed |
Select to enable MO SMS Subscribed and select true or false. Tcl Parameter: NudmSmsMngSubDataMoSmsSubEn Tcl Parameter: NudmSmsMngSubDataMoSmsSub |
M0 SMS Barring All |
Select to enable MO SMS Barring All and select true or false. Tcl Parameter: NudmSmsMngSubDataMoSmsBarAllEn Tcl Parameter: NudmSmsMngSubDataMoSmsBarAll |
M0 SMS Barring Roaming |
Select to enable MO SMS Barring Roaming and select true or false. Tcl Parameter: NudmSmsMngSubDataMoSmsBarRoamEn Tcl Parameter: NudmSmsMngSubDataMoSmsBarRoam |
Supported Features |
Select to enter Supported Features. pattern: '^[A-Fa-f0-9]*$' max length 128 bytes Tcl Parameter: NudmSmsMngSubDataSupFeatEn Tcl Parameter: NudmSmsMngSubDataSupFeat |
Shared SMS Management Data IDs |
Select to enter up to 8 SMS Management Data IDs. Tcl Parameter: NudmSmsMngSubDataSharedSmsMngDataIdEn Tcl Parameter: NudmSmsMngSubDataSharedSmsMngDataIdNum Tcl Parameter: NudmSmsMngSubDataSharedSmsMngDataId_1 |
Group Number |
Available Nudm Version >= 16.7.0/Mar2021. Select to enter the External Group ID Setting. Select up to 10 Group Numbers. Range : 0 to 10 Default : 0 Enter Starting UE Index, Ending UE Index and Group Identity. Starting UE Index must less than Ending UE Index, Group Identity should following format as (extgroupid-[^@]+@[^@]+) Default : [email protected] Tcl Parameter: NudmGrpIdNum Tcl Parameter: NudmGrpId_1 |
See topic Nf Services