Landslide emulates Access Points (WAN Nodes) and provides configuration to test WAN Node. You can emulate multiple nodes with the Number of APs setting1.
NOTE: Num of Nodes depends on your license capacity. |
Activation Rate | Indicates the number of Access Point1 links that the test attempts to establish every second. Tcl Parameter: WanStartRate |
Deactivation Rate | Indicates the number of Access Point links1 that the test attempts to tear down every second. All UEs must successfully detach from the WOGW before any Access Point links are torn down. Tcl Parameter: WanDisconnectRate |
Skip 0 IP address | If enabled will skip the x.x.x.0 IP address and use x.x.x.1 instead. Available only in Wifi Offload Gateway Nodal TC. Tcl Parameter: WanNodeSkip0IpsEn |
Failed Threshold (%) | Range from 0 to 100, Default = 0. Indicates the tolerance for failed AP connection. A value of 0 (zero) means zero tolerance. Used to configure the percentage (%) of APs that may connect in order to continue a test. If the percentage of APs that fail to connect is more than the Failed Threshold % entered then the test case stops. If the percentage of APs that connect is more than the (100 - Failed Threshold) % entered, then the test case continues with the understanding that the UEs assigned to those APs that failed to connect will not participate in the test. For example: When Number of Subscribers = 10 and the Failed Threshold (%) = 49, that means that at most 4 subscribers (less than 49 %) fail to connect in order for the test to continue. Available only in Wifi Offload Gateway Nodal TC. Tcl Parameter: ApFailedThresholdPercent |
MAC Address Increment |
Enter an increment value used to increment MAC Address. Available if MAC Address is enabled on the Physical Interface and if AP Tunnel type = GRE L2, CAPWAP, or NONE. Range : 1 to 65535 Default : 1 Tcl Parameter: WanNodeMacAddrIncrement |
MCC MNC |
Available in AMF Nodal test case. Enter the Mobile Country Code (3 digits) and the Mobile Network Code (2 or 3 digits). Default : 000 Tcl Parameter: ApWanMcc Tcl Parameter: ApWanMnc |
Set ID Region ID SNPN NID |
Available in AMF Nodal test case. Enter the Pointer. Range: 0 to 63. Default: 0 Enter the Set ID: The Set consists of some AMFs that serve a given area and network slice. Multiple AMF sets may be defined per AMF region and network slice. Range: 0 to 1023. Default: 0 Enter the Region ID. The AMF Region consists of one or more multiple AMF Sets. Range: 0 to 255. Default: 0 Enter Standalone Non-Public-Networks (SNPN) by adding NID configuration to PLMN ID's used for SNPN in network sharing mode. Up to 11 HEX Characters. A default value of zero is used to indicate that NID has not been configured for the PLMN ie PLMN is not an NPN. Requires SNPN license + NGAP version 16.2.0 or higher. Per Reference : 3GPP TS 23.501 v16.2.0: System Architecture for the 5G System , 3GPP TS 38.413 v16.2.0: NG-RAN; NG Application Protocol (NGAP) , 3GPP TS 23.003 v16.2.0: Numbering, addressing and identification. Tcl Parameter: ApWanPointer Tcl Parameter: ApWanSetId Tcl Parameter: ApWanRegion Tcl Parameter: ApWanSnpnNid |
With an Ethernet User Node, you can define:
The IP address and routing options... The IP Address (IPv4 or IPv6) will increment for each node.
The MAC Address to override the Hardware MAC address so the packets sent out of the interface will use the provisioned MAC address rather the Hardware MAC Address.
NOTE: In the Wifi Offload Gateway Nodal test case, when the Tunnel Type is GRE L2 (on Test Configuration tab)) and the GRE Vendor Variant is Variant 1 (on GRE tab), you are required to select MAC Address and enter the appropriate value. An error displays if no value is entered. |
Custom port selection... and error injection with the Advanced... button.
The Outbound Traffic Port to disable the normal routing function and to force packets out of the selected interface.
1 Maximum rates, number of sessions, and number of emulated nodes vary depending on the test configuration and the test system's licensed capacity.