LPP Tab


The LPP/LPPa (LTE Positioning Protocol) tab is used in the AMF Nodal, AMF Node , IP Application Node (via DMF - ulp), gNB CU SA Nodal  ,LCS,  MME, and Service Based Node Test cases for Location Services.

Spec 3GPP 36.355

Location Data

Location Estimate

Velocity Estimate

 

Location Error

Message Payload (Client)

Message Payload (Server)

 

    E-CID Measurement

 

 

 

Support Request Position Info from On-Demand Command

Request Position Info

Request Position Info

WLAN-based Positioning

WLAN-based Positioning

 

 

Related Measurements

Measurements collected for LPP related processing are reported on the LPP Server Session and LPP Client Session report tab.


Support On-Demand Command

Select for Command Mode for LPPa conversations (ECID). Available in the MME Node Test Case when "Command Mode" is selected in Emulation Configuration. It will be disabled when Slg Interface is enabled. E-CID Measurement pane becomes available for input.

Per 3GPP TS 36.455 v15.1.0.

Tcl Parameter: LppSrvOdcEn

LPP Location Info Delay (s)

 

Number of Additional LPP Location Info Delay (s)

Enable to enter a Location Info delay in seconds.

Range: 0 to 65535

Default: 2

Select Number of Additional LPP Location Info Delay (s) to add up to 3 additional location info delays to respond to  RequestLocationInformation separately when there are multiple incoming RequestLocationInformation. 

Enter Delay (s) - Range 0 to 65535

Tcl Parameter: LppClnLppProvideLocDelayEn

Tcl Parameter: LppClnLppProvideLocDelay

Tcl Parameter: LppClnAddLppProvideLocDelayNum

Tcl Parameter: LppClnAddLppProvideLocDelay_1

Disable LPP Procedure

Available on the LCS|LPP tab for AMF Nodal. Available on the LMF|LPP tab for AMF Node.

Select to disable the LPP procedure for LMF function in AMF Node test case and in LCS function for AMF Nodal test case.

Tcl Parameter: LppClnDisableLppProcEn

Tcl Parameter: LppSrvDisableLppProcEn

LPPa ECID Init Response Delay (s)

 

Enable to enter an ECID Init Response delay in seconds.

Range: 0 to 65535

Default: 5

Tcl Parameter: LppClnLppaEcidInitRspDelayEn

Tcl Parameter: LppClnLppaEcidInitRspDelay

Enable LPPa

Select to initiate/trigger LPPa conversations (ECID). Available in LCS Node and MME Node Test Cases.

Tcl Parameter: LppSrvLppaEn

E-CID Measurement

Select to include E-CID (Enhanced Cell-ID - positioning method) Measurement. Available in MME Node Test Case when Support On-Demand Command is enabled.

The purpose of E-CID Measurement Initiation procedure is to allow the LMF to request the NG-RAN node to report E-CID measurements used by LMF to compute the location of the UE.

Tcl Parameter: LppSrvEcidMeasEn

Report characteristics

 

Measurement Periodicity

 

Terminate on Report Count

Select the Report Characteristics to produce the report either "OnDemand" or "Periodic" - periodically. If "Periodic" is enabled, select the Measurement Periodicity and Report Number.

Select the Measurement Periodicity.

Options : 120ms, 240ms, 480ms, 640ms, 1024ms, 2048ms, 5120ms, 10240ms (default), 1min, 6 min, 12 min, 30 min, 60 min, 20480ms, 40960ms

Select to enable the Terminate on Report Count. This parameter is used to control if / when to send Ecid Measurement Termination Command.

If Terminate on Report Count is not enabled, the Ecid Measurement Termination Command will not be sent.

A value of Zero (0) means, the Ecid Measurement Termination Command will be sent immediately after Ecid Measurement Initiation Request.

Any other value means that the Ecid Measurement Termination Command will be sent after we receive the corresponding number of Ecid Measurement Report.

Options : 0 to 127, Default : 1

Tcl Parameter: LppaSrvEcidReportChars

Tcl Parameter: LppaSrvEcitMeasPeriod

Tcl Parameter: LppaSrvEcidReportNumEn

Tcl Parameter: LppaSrvEcidReportNum

Measurement Quantities

Select the Measurement Quantities item.

Options : Cell-ID, Angle of Arrival, Timing Advance Type 1, Timing Advance Type 2, RSRP,  RSRQ

Default : Cell-ID

cl Parameter: LppaSrvEcidMeasQtys

Inter-RAT Measurement Quantities

Select the Inter-RAT Measurement Quantities item.

Options: GERAN, UTRAN

cl Parameter: LppaSrvEcidInterRatMeasQtys

WLAN Measurement Quantities

Select the WLAN Measurement Quantities item.

Options: WLAN

cl Parameter: LppaSrvEcidWlanMeasQtys

 

Enable OTDOA

Select to initiate/trigger LPPa conversations (OTDOA). Available in LCS Node and MME Node Test Cases.

Tcl Parameter: LppSrvOtdoaEn

Send Request Location Information Separately

Select to send multiple Request Location Information messages, each with separate position method.

Available in LCS Node Node Test Case.

Tcl Parameter: LppSrvSendReqLocInfoSeparatelyEn

OTDOA Information

Available in MME Node Test Case when Support On-Demand Command is enabled.

Select to include OTDOA (Observed Time Difference of Arrival) information type. 

 

The available items are as following: pci (default), cellid, tac, earfcn, prsBandwidth

, prsConfigIndex, cpLength, noDlFrames, noAntennaPorts, sFNInitTime, 

e-UTRANAccessPointPosition, prsmutingconfiguration, prsid, tpid, tpType,

crsCPlength, MBSFNsubframeConfiguration, nPRSConfiguration, offsetNBChanneltoEARFCN,

operationModeInfo, NPRS-ID, dlBandwidth, multipleprsConfigurationsperCell, prsOccasionGroup, prsFrequencyHoppingConfiguration, repetitionNumberofSIB1-NB, nPRSsequenceInfo,  NPRS Type 2

Tcl Parameter: LppaSrvOtdoaInfoEn

Tcl Parameter: LppaSrvOtdoaInfoType

Neighbor Cell Info

Available when both Enable LPPa and Enable OTDOA are enabled. Available in LCS Node and MME Node Test Cases.

Per 3GPP 36.355 and 36.455 for latest NB-IoT support.

Enter the Number of Neighbor Cells from 0 to 9.

Tcl Parameter: LppSrvNumNeighborCell

Cell

Enter Neighbor Cell details for each Cell group.

Range: 0 — 9

PCI

Enter PCI.

Range : -1 to 503

Default: -1 (means do not include in the configuration)

Tcl Parameter: OtdoaNeighborCellPci_0

Slot Number Offset

Enter Slot Number Offset.

Range : -1 to 19

Default: -1 (means do not include in the configuration)

Tcl Parameter: OtdoaNeighborCellSlotNumOffset_0

PRS Subframe Offset

Enter PRS Subframe Offset.

Range : -1 to 1279

Default: -1 (means do not include in the configuration)

Tcl Parameter: OtdoaNeighborCellPrsSubframeOffset_0

Expected RSTD

Enter Expected RSTD.

Range : -1 to 16383

Default: -1 (means do not include in the configuration)

Tcl Parameter: OtdoaNeighborCellExpectedRstd_0

Expected RSTD Un

Enter Expected RSTD Un.

Range : -1 to 1023

Default: -1 (means do not include in the configuration)

Tcl Parameter: OtdoaNeighborCellExpectedRstdUn_0

NPRS Slot Number Offset

Enter NPRS Slot Number Offset.

Range : -1 to 19

Default: -1 (means do not include in the configuration)

Tcl Parameter: OtdoaNeighborCellNprsSlotNumOffset_0

NPRS SFN Offset

Enter NPRS SFN Offset.

Range : -1 to 19

Default: -1 (means do not include in the configuration)

Tcl Parameter: OtdoaNeighborCellNprsSfnOffset_0

NPRS Subframe Offset

Enter NPRS Subframe Offset.

Range : -1 to 1279

Default: -1 (means do not include in the configuration)

Tcl Parameter: OtdoaNeighborCellNprsSubframeOffset_0

NB Expected RSTD

Enter Expected NB RSTD.

Range : -1 to 16383

Default: -1 (means do not include in the configuration)

Tcl Parameter: OtdoaNeighborCellNbExpectedRstd_0

NB Expected RSTD Un

Enter Expected NB RSTD Un.

Range : -1 to 1023

Default: -1 (means do not include in the configuration)

Tcl Parameter: OtdoaNeighborCellNbExpectedRstdUn_0

 

Apply Test Data File to LPP/LPPa

Apply Parameter Values from Test Data Files (LPP).

3gpp 36.355 f10

TDFs have been updated to include the OTDOA Information elements in LPP to support the latest spec for NB-IoT.

TDF - Node Side (MME Node & LCS Node) TDF - 120

Column Name

Values

Default Value

Provide AD Otdoa Neighbor Cell Info Present

0 or 1

0

Provide AD Otdoa Ref Cell Info NB Present

0 or 1

0

Provide AD Otdoa Neighbor Cell Info NB Present

0 or 1

0

OTDOA Cell Info PRS ID Req

0 or 1

0

OTDOA Cell Info TP ID Req

0 or 1

0

OTDOA Cell Info TP TYPE Req

0 or 1

0

OTDOA Cell Info CRS CP Length Req

0 or 1

0

OTDOA Cell Info NPRS Configuration Req

0 or 1

0

OTDOA Cell Info Offset of NB CN to DL EARFCN Req

0 or 1

0

OTDOA Cell Info Operation Mode Info Req

0 or 1

0

OTDOA Cell Info NPRS ID Req

0 or 1

0

OTDOA Cell Info DL Bandwidth Req

0 or 1

0

OTDOA Cell Info PRS Occasion Group Req

0 or 1

0

OTDOA Cell Info Repetition Number of SIB1-NB Req

0 or 1

0

OTDOA Cell Info NPRS Sequence Info Req

0 or 1

0

OTDOA Cell Info NPRS Configuration Type2 Req

0 or 1

0

 

Nodal Side (MME Nodal & LCS Nodal) TDF - 107

Column Name

Values

Default Value

Provide Cap OTDOA Mode

The decimal format of 8bits. Should be 8(ue-assisted) , 4(ue-assisted-NB-r14), or 12(ue-assisted and ue-assisted-NB-r14)

0

Provide Cap Dense PRS Config

1: supported

0: Not supported

0

Provide Cap Idle State For Measurements

1: required

0: Not required

0

Request AD Otdoa Ad Type

The decimal format of 8bits. Should be 8(prs) , 4(nprs), or 12(prs and nprs)

0

Provide Loc Info Otdoa Sig Measure Info NB Present

0 or 1

0

OTDOA Cell Info PRS ID

Integer. Value should meet the requirement in 36.455

0

OTDOA Cell Info TP ID

0

OTDOA Cell Info TP Type

0

OTDOA Cell Info Number of DL Frames-Extended

0

OTDOA Cell Info CRS CP Length

0

OTDOA Cell Info Bitmaps for NPRS Subframes

The decimal format of 64 bits.

0

 

Integer. Value should meet the requirements in 36.455

 

OTDOA Cell Info Bitmaps for NPRS Choice

0

OTDOA Cell Info Number of NPRS Subframes in One Occasion

0

OTDOA Cell Info Periodicity of NPRS

0

OTDOA Cell Info Starting Subframe Offset of NPRS Occasion

0

OTDOA Cell Info Offset of NB-IoT Channel Num to DL EARFCN

0

OTDOA Cell Info Operation Mode Info

0

OTDOA Cell Info NPRS ID

0

OTDOA Cell Info DL Bandwidth

0

OTDOA Cell Info PRS Occasion Group

0

OTDOA Cell Info Repetition Number of SIB1-NB

0

OTDOA Cell Info NPRS Sequence Info

0

 

Examples Containing the new OTDOA Parameters:

UE_OTDOA OK.csv and ECML_OTDOA.csv

Added support for additional LPP parameters related to GNSS positioning method to be configurable by TDF to AMF Nodal, MME Nodal and Data Message Flow (DMF). 

See sample file with GNSS parameters  - GNSS.csv

 

 

TDF Column Name Configure Parameter Name Value Type Value Range Remark
Provide Cap GNSS Support List Element Num provide_cap_gnss_supt_list_elem_num integer [1, 3] It specifies the number of GNSS-SupportElement in gnss-SupportList of a-gnss-ProvideCapabilities.
1 The parameters for the first GNSS-SupportElement in gnss-SupportList of a-gnss-ProvideCapabilities:
Provide Cap GNSS Support Element 1 GNSS Id provide_cap_gnss_supt_elem_1_gnss_id  integer [0, 5]

It specifies the value of gnss-ID in GNSS-SupportElement.

0 donates for gps, 1 for sbas, 2 for qzss, 3 for galileo, 4 for glonass, 5 for bds.

Provide Cap GNSS Support Element 1 SBAS IDs present provide_cap_gnss_supt_elem_1_sbas_ids_present integer [0, 1]

It specifies if sbas-IDs will be present in GNSS-SupportElement.

For all the parameters with "present" as suffix, 0 means this IE will not be present, 1 means it will be present. 

Provide Cap GNSS Support Element 1 FTA MeasSupport present provide_cap_gnss_supt_elem_1_fta_meassupport_present integer [0, 1] It specifies if fta-MeasSupport will be present in GNSS-SupportElement.
Provide Cap GNSS Support Element 1 SBAS IDs provide_cap_gnss_supt_elem_1_sbas_ids one-byte long hex string  

It specifies the value of sbas-IDs in GNSS-SupportElement.

It is a bitmap parameter with 8 bits long, the bit form the left most donates for  waas, then egnos, then msas, and then gagan. For example, 80 donates for waas, 40 for egnos, 20 for msas, 10 for gagan, c0 for waas and egnos, and so on.

Provide Cap GNSS Support Element 1 A-GNSS Modes provide_cap_gnss_supt_elem_1_agnss_modes one-byte long hex string  

It specifies the value of agnss-Modes in GNSS-SupportElement.

It is a bitmap parameter with 8 bits long, the bit form the left most donates for  standalone, then ue-based, then ue-assisted. For example, 80 donates for standalone, 40 for ue-based, 20 for ue-assisted, c0 for standalone and ue-based, and so on.

Provide Cap GNSS Support Element 1 GNSS Signals provide_cap_gnss_supt_elem_1_gnss_signals one-byte long hex string  

It specifies the value of gnss-Signals in GNSS-SupportElement.

It is a bitmap parameter with 8 bits long.

Provide Cap GNSS Support Element 1 FTA MeasSupport Cell Time provide_cap_gnss_supt_elem_1_fta_meassupt_cell_time one-byte long hex string  

It specifies the value of cellTime for fta-MeasSupport in GNSS-SupportElement.

It is a bitmap parameter with 8 bits long. The bit form the left most donates for eutra, then utra, then gsm, then nb-iot, and nr-v1510. For example, 80 donates for eutra, 40 donates utra, and so on.

Provide Cap GNSS Support Element 1 FTA MeasSupport Mode provide_cap_gnss_supt_elem_1_fta_meassupt_mode one-byte long hex string  

It specifies the value of mode for fta-MeasSupport in GNSS-SupportElement.

It is a bitmap parameter with 8 bits long, the bit form the left most donates for  standalone, then ue-based, then ue-assisted. For example, 80 donates for standalone, 40 for ue-based, 20 for ue-assisted, c0 for standalone and ue-based, and so on.

Provide Cap GNSS Support Element 1 ADR Support provide_cap_gnss_supt_elem_1_adr_supt integer [0, 1]

It specifies the value of adr-Support in GNSS-SupportElement.

0 for false, 1 for true.

Provide Cap GNSS Support Element 1 Velocity Measurement Support provide_cap_gnss_supt_elem_1_velocity_meassupt integer [0, 1]

It specifies the value of velocityMeasurementSupport in GNSS-SupportElement.

0 for false, 1 for true.

2 The parameters for the second GNSS-SupportElement in gnss-SupportList of a-gnss-ProvideCapabilities:
Provide Cap GNSS Support Element 2 GNSS Id provide_cap_gnss_supt_elem_2_gnss_id  integer [0, 5]

It specifies the value of gnss-ID in GNSS-SupportElement.

0 donates for gps, 1 for sbas, 2 for qzss, 3 for galileo, 4 for glonass, 5 for bds.

Provide Cap GNSS Support Element 2 SBAS IDs present provide_cap_gnss_supt_elem_2_sbas_ids_present integer [0, 1]

It specifies if sbas-IDs will be present in GNSS-SupportElement.

For all the parameters with "present" as suffix, 0 means this IE will not be present, 1 means it will be present. 

Provide Cap GNSS Support Element 2 FTA MeasSupport present provide_cap_gnss_supt_elem_2_fta_meassupport_present integer [0, 1] It specifies if fta-MeasSupport will be present in GNSS-SupportElement.
Provide Cap GNSS Support Element 2 SBAS IDs provide_cap_gnss_supt_elem_2_sbas_ids one-byte long hex string  

It specifies the value of sbas-IDs in GNSS-SupportElement.

It is a bitmap parameter with 8 bits long, the bit form the left most donates for  waas, then egnos, then msas, and then gagan. For example, 80 donates for waas, 40 for egnos, 20 for msas, 10 for gagan, c0 for waas and egnos, and so on.

Provide Cap GNSS Support Element 2 A-GNSS Modes provide_cap_gnss_supt_elem_2_agnss_modes one-byte long hex string  

It specifies the value of agnss-Modes in GNSS-SupportElement.

It is a bitmap parameter with 8 bits long, the bit form the left most donates for  standalone, then ue-based, then ue-assisted. For example, 80 donates for standalone, 40 for ue-based, 20 for ue-assisted, c0 for standalone and ue-based, and so on.

Provide Cap GNSS Support Element 2 GNSS Signals provide_cap_gnss_supt_elem_2_gnss_signals one-byte long hex string  

It specifies the value of gnss-Signals in GNSS-SupportElement.

It is a bitmap parameter with 8 bits long.

Provide Cap GNSS Support Element 2 FTA MeasSupport Cell Time provide_cap_gnss_supt_elem_2_fta_meassupt_cell_time one-byte long hex string  

It specifies the value of cellTime for fta-MeasSupport in GNSS-SupportElement.

It is a bitmap parameter with 8 bits long. The bit form the left most donates for eutra, then utra, then gsm, then nb-iot, and nr-v1510. For example, 80 donates for eutra, 40 donates utra, and so on.

Provide Cap GNSS Support Element 2 FTA MeasSupport Mode provide_cap_gnss_supt_elem_2_fta_meassupt_mode one-byte long hex string  

It specifies the value of mode for fta-MeasSupport in GNSS-SupportElement.

It is a bitmap parameter with 8 bits long, the bit form the left most donates for  standalone, then ue-based, then ue-assisted. For example, 80 donates for standalone, 40 for ue-based, 20 for ue-assisted, c0 for standalone and ue-based, and so on.

Provide Cap GNSS Support Element 2 ADR Support provide_cap_gnss_supt_elem_2_adr_supt integer [0, 1]

It specifies the value of adr-Support in GNSS-SupportElement.

0 for false, 1 for true.

Provide Cap GNSS Support Element 2 Velocity Measurement Support provide_cap_gnss_supt_elem_2_velocity_meassupt integer [0, 1]

It specifies the value of velocityMeasurementSupport in GNSS-SupportElement.

0 for false, 1 for true.

3

The parameters for the third GNSS-SupportElement in gnss-SupportList of a-gnss-ProvideCapabilities:

Provide Cap GNSS Support Element 3 GNSS Id provide_cap_gnss_supt_elem_3_gnss_id  integer [0, 5]

It specifies the value of gnss-ID in GNSS-SupportElement.

0 donates for gps, 1 for sbas, 2 for qzss, 3 for galileo, 4 for glonass, 5 for bds.

Provide Cap GNSS Support Element 3 SBAS IDs present provide_cap_gnss_supt_elem_3_sbas_ids_present integer [0, 1]

It specifies if sbas-IDs will be present in GNSS-SupportElement.

For all the parameters with "present" as suffix, 0 means this IE will not be present, 1 means it will be present. 

Provide Cap GNSS Support Element 3 FTA MeasSupport present provide_cap_gnss_supt_elem_3_fta_meassupport_present integer [0, 1] It specifies if fta-MeasSupport will be present in GNSS-SupportElement.
Provide Cap GNSS Support Element 3 SBAS IDs provide_cap_gnss_supt_elem_3_sbas_ids one-byte long hex string  

It specifies the value of sbas-IDs in GNSS-SupportElement.

It is a bitmap parameter with 8 bits long, the bit form the left most donates for  waas, then egnos, then msas, and then gagan. For example, 80 donates for waas, 40 for egnos, 20 for msas, 10 for gagan, c0 for waas and egnos, and so on.

Provide Cap GNSS Support Element 3 A-GNSS Modes provide_cap_gnss_supt_elem_3_agnss_modes one-byte long hex string  

It specifies the value of agnss-Modes in GNSS-SupportElement.

It is a bitmap parameter with 8 bits long, the bit form the left most donates for  standalone, then ue-based, then ue-assisted. For example, 80 donates for standalone, 40 for ue-based, 20 for ue-assisted, c0 for standalone and ue-based, and so on.

Provide Cap GNSS Support Element 3 GNSS Signals provide_cap_gnss_supt_elem_3_gnss_signals one-byte long hex string  

It specifies the value of gnss-Signals in GNSS-SupportElement.

It is a bitmap parameter with 8 bits long.

Provide Cap GNSS Support Element 3 FTA MeasSupport Cell Time provide_cap_gnss_supt_elem_3_fta_meassupt_cell_time one-byte long hex string  

It specifies the value of cellTime for fta-MeasSupport in GNSS-SupportElement.

It is a bitmap parameter with 8 bits long. The bit form the left most donates for eutra, then utra, then gsm, then nb-iot, and nr-v1510. For example, 80 donates for eutra, 40 donates utra, and so on.

Provide Cap GNSS Support Element 3 FTA MeasSupport Mode provide_cap_gnss_supt_elem_3_fta_meassupt_mode one-byte long hex string  

It specifies the value of mode for fta-MeasSupport in GNSS-SupportElement.

It is a bitmap parameter with 8 bits long, the bit form the left most donates for  standalone, then ue-based, then ue-assisted. For example, 80 donates for standalone, 40 for ue-based, 20 for ue-assisted, c0 for standalone and ue-based, and so on.

Provide Cap GNSS Support Element 3 ADR Support provide_cap_gnss_supt_elem_3_adr_supt integer [0, 1]

It specifies the value of adr-Support in GNSS-SupportElement.

0 for false, 1 for true.

Provide Cap GNSS Support Element 3 Velocity Measurement Support provide_cap_gnss_supt_elem_3_velocity_meassupt integer [0, 1]

It specifies the value of velocityMeasurementSupport in GNSS-SupportElement.

0 for false, 1 for true.

Request AD Gnss Time Req Pref List Gnss Id Num req_ad_gnss_time_req_pref_list_gnss_id_num integer [1, 3]

It specifies the number of GNSS IDs in gnss-TimeReqPrefList of GNSS-ReferenceTimeReq.

Request AD Gnss Time Req Pref List Gnss Id 1 req_ad_gnss_time_req_pref_list_gnss_id_1 integer [0, 5]

It specifies the value of GNSS-ID in gnss-TimeReqPrefList of GNSS-ReferenceTimeReq.

0 donates for gps, 1 for sbas, 2 for qzss, 3 for galileo, 4 for glonass, 5 for bds.

Request AD Gnss Time Req Pref List Gnss Id 2 req_ad_gnss_time_req_pref_list_gnss_id_2
Request AD Gnss Time Req Pref List Gnss Id 3 req_ad_gnss_time_req_pref_list_gnss_id_3
Provide Loc Info Gnss Sig Measure Gnss Id provide_loc_info_gnss_sig_measure_gnss_id

It specifies the value of gnss-ID in gnss-MeasurementList. We only support one GNSS-MeasurementForOneGNSS in gnss-MeasurementList now.

0 donates for gps, 1 for sbas, 2 for qzss, 3 for galileo, 4 for glonass, 5 for bds.

Provide Loc Info Gnss Sgn Measure CodePhase Ambiguity present provide_loc_info_gnss_sgn_measure_codephase_amb_present integer [0, 1] It specifies if gnss-CodePhaseAmbiguity will be present in gnss-SgnMeasList. We only support one GNSS-SgnMeasElement for gnss-SgnMeasList.
Provide Loc Info Gnss Sgn Measure CodePhase Ambiguity provide_loc_info_gnss_sgn_measure_codephase_amb integer [0, 127]

It specifies the value of gnss-CodePhaseAmbiguity in gnss-SgnMeasList.

Provide Loc Info Gnss Sgn Measure Signal Id provide_loc_info_gnss_sgn_measure_sig_id integer [0, 7] It specifies the value of gnss-SignalID in gnss-SgnMeasList.
Provide Loc Info Gnss Sat Measure List Element Num provide_loc_info_gnss_sat_meas_list_elem_num integer [1, 7] It specifies the number of GNSS-SatMeasElement in gnss-SgnMeasList.












1
The parameters for the 1st GNSS-SatMeasElement in gnss-SgnMeasList:
Provide Loc Info Gnss Sat Measure Element 1 Carrier Quality Ind present provide_loc_info_gnss_sat_meas_elem_1_carr_qa_ind_present integer [0, 1] It specifies if carrierQualityInd will be present in GNSS-SatMeasElement.
Provide Loc Info Gnss Sat Measure Element 1 Integer Code Phase present provide_loc_info_gnss_sat_meas_elem_1_int_code_phase_present integer [0, 1] It specifies if integerCodePhase will be present in GNSS-SatMeasElement.
Provide Loc Info Gnss Sat Measure Element 1 Doppler present provide_loc_info_gnss_sat_meas_elem_1_doppler_present integer [0, 1] It specifies if dopplerwill be present in GNSS-SatMeasElement.
Provide Loc Info Gnss Sat Measure Element 1 ADR present provide_loc_info_gnss_sat_meas_elem_1_adr_present integer [0, 1] It specifies if adr be present in GNSS-SatMeasElement.
Provide Loc Info Gnss Sat Measure Element 1 Sat Id provide_loc_info_gnss_sat_meas_elem_1_sat_id integer [0, 63] It specifies the svID in GNSS-SatMeasElement.
Provide Loc Info Gnss Sat Measure Element 1 cNo provide_loc_info_gnss_sat_meas_elem_1_cno integer [0, 63] It specifies the cNo in GNSS-SatMeasElement.
Provide Loc Info Gnss Sat Measure Element 1 mpath Det provide_loc_info_gnss_sat_meas_elem_1_mpatch_det integer [0, 3]

It specifies the mpathDet in GNSS-SatMeasElement.

0 for notMeasured, 1 for low, 2 for medium, 3 for high.

Provide Loc Info Gnss Sat Measure Element 1 Code Phase RMS Error provide_loc_info_gnss_sat_meas_elem_1_code_phase_rms_err integer [0, 63] It specifies the codePhaseRMSError in GNSS-SatMeasElement.
Provide Loc Info Gnss Sat Measure Element 1 Code Phase provide_loc_info_gnss_sat_meas_elem_1_code_phase integer [0, 2097151] It specifies the codePhase in GNSS-SatMeasElement.
Provide Loc Info Gnss Sat Measure Element 1 Carrier Quality Ind provide_loc_info_gnss_sat_meas_elem_1_carr_qa_ind integer [0, 3] It specifies the carrierQualityInd in GNSS-SatMeasElement.
Provide Loc Info Gnss Sat Measure Element 1 Integer Code Phase provide_loc_info_gnss_sat_meas_elem_1_int_code_phase integer [0, 127] It specifies the integerCodePhase in GNSS-SatMeasElement.
Provide Loc Info Gnss Sat Measure Element 1 Doppler provide_loc_info_gnss_sat_meas_elem_1_doppler integer

[-32768, 32767]

It specifies the doppler in GNSS-SatMeasElement.
Provide Loc Info Gnss Sat Measure Element 1 Adr provide_loc_info_gnss_sat_meas_elem_1_adr integer [0, 33554431] It specifies the adr in GNSS-SatMeasElement.












2
The parameters for the 2nd GNSS-SatMeasElement in gnss-SgnMeasList:
Provide Loc Info Gnss Sat Measure Element 2 Carrier Quality Ind present provide_loc_info_gnss_sat_meas_elem_2_carr_qa_ind_present      
Provide Loc Info Gnss Sat Measure Element 2 Integer Code Phase present provide_loc_info_gnss_sat_meas_elem_2_int_code_phase_present      
Provide Loc Info Gnss Sat Measure Element 2 Doppler present provide_loc_info_gnss_sat_meas_elem_2_doppler_present      
Provide Loc Info Gnss Sat Measure Element 2 ADR present provide_loc_info_gnss_sat_meas_elem_2_adr_present      
Provide Loc Info Gnss Sat Measure Element 2 Sat Id provide_loc_info_gnss_sat_meas_elem_2_sat_id integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 2 cNo provide_loc_info_gnss_sat_meas_elem_2_cno integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 2 mpath Det provide_loc_info_gnss_sat_meas_elem_2_mpatch_det integer [0, 3] 0 for notMeasured, 1 for low, 2 for medium, 3 for high.
Provide Loc Info Gnss Sat Measure Element 2 Code Phase RMS Error provide_loc_info_gnss_sat_meas_elem_2_code_phase_rms_err integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 2 Code Phase provide_loc_info_gnss_sat_meas_elem_2_code_phase integer [0, 2097151]  
Provide Loc Info Gnss Sat Measure Element 2 Carrier Quality Ind provide_loc_info_gnss_sat_meas_elem_2_carr_qa_ind integer [0, 3]  
Provide Loc Info Gnss Sat Measure Element 2 Integer Code Phase provide_loc_info_gnss_sat_meas_elem_2_int_code_phase integer [0, 127]  
Provide Loc Info Gnss Sat Measure Element 2 Doppler provide_loc_info_gnss_sat_meas_elem_2_doppler integer

[-32768, 32767]

 
Provide Loc Info Gnss Sat Measure Element 2 Adr provide_loc_info_gnss_sat_meas_elem_2_adr integer [0, 33554431]  
3











 
The parameters for the 3rd GNSS-SatMeasElement in gnss-SgnMeasList:
Provide Loc Info Gnss Sat Measure Element 3 Carrier Quality Ind present provide_loc_info_gnss_sat_meas_elem_3_carr_qa_ind_present      
Provide Loc Info Gnss Sat Measure Element 3 Integer Code Phase present provide_loc_info_gnss_sat_meas_elem_3_int_code_phase_present      
Provide Loc Info Gnss Sat Measure Element 3 Doppler present provide_loc_info_gnss_sat_meas_elem_3_doppler_present      
Provide Loc Info Gnss Sat Measure Element 3 ADR present provide_loc_info_gnss_sat_meas_elem_3_adr_present      
Provide Loc Info Gnss Sat Measure Element 3 Sat Id provide_loc_info_gnss_sat_meas_elem_3_sat_id integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 3 cNo provide_loc_info_gnss_sat_meas_elem_3_cno integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 3 mpath Det provide_loc_info_gnss_sat_meas_elem_3_mpatch_det integer [0, 3] 0 for notMeasured, 1 for low, 2 for medium, 3 for high.
Provide Loc Info Gnss Sat Measure Element 3 Code Phase RMS Error provide_loc_info_gnss_sat_meas_elem_3_code_phase_rms_err integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 3 Code Phase provide_loc_info_gnss_sat_meas_elem_3_code_phase integer [0, 2097151]  
Provide Loc Info Gnss Sat Measure Element 3 Carrier Quality Ind provide_loc_info_gnss_sat_meas_elem_3_carr_qa_ind integer [0, 3]  
Provide Loc Info Gnss Sat Measure Element 3 Integer Code Phase provide_loc_info_gnss_sat_meas_elem_3_int_code_phase integer [0, 127]  
Provide Loc Info Gnss Sat Measure Element 3 Doppler provide_loc_info_gnss_sat_meas_elem_3_doppler integer

[-32768, 32767]

 
Provide Loc Info Gnss Sat Measure Element 3 Adr provide_loc_info_gnss_sat_meas_elem_3_adr integer [0, 33554431]  












4
The parameters for the 4th GNSS-SatMeasElement in gnss-SgnMeasList:
Provide Loc Info Gnss Sat Measure Element 4 Carrier Quality Ind present provide_loc_info_gnss_sat_meas_elem_4_carr_qa_ind_present      
Provide Loc Info Gnss Sat Measure Element 4 Integer Code Phase present provide_loc_info_gnss_sat_meas_elem_4_int_code_phase_present      
Provide Loc Info Gnss Sat Measure Element 4 Doppler present provide_loc_info_gnss_sat_meas_elem_4_doppler_present      
Provide Loc Info Gnss Sat Measure Element 4 ADR present provide_loc_info_gnss_sat_meas_elem_4_adr_present      
Provide Loc Info Gnss Sat Measure Element 4 Sat Id provide_loc_info_gnss_sat_meas_elem_4_sat_id integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 4 cNo provide_loc_info_gnss_sat_meas_elem_4_cno integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 4 mpath Det provide_loc_info_gnss_sat_meas_elem_4_mpatch_det integer [0, 3] 0 for notMeasured, 1 for low, 2 for medium, 3 for high.
Provide Loc Info Gnss Sat Measure Element 4 Code Phase RMS Error provide_loc_info_gnss_sat_meas_elem_4_code_phase_rms_err integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 4 Code Phase provide_loc_info_gnss_sat_meas_elem_4_code_phase integer [0, 2097151]  
Provide Loc Info Gnss Sat Measure Element 4 Carrier Quality Ind provide_loc_info_gnss_sat_meas_elem_4_carr_qa_ind integer [0, 3]  
Provide Loc Info Gnss Sat Measure Element 4 Integer Code Phase provide_loc_info_gnss_sat_meas_elem_4_int_code_phase integer [0, 127]  
Provide Loc Info Gnss Sat Measure Element 4 Doppler provide_loc_info_gnss_sat_meas_elem_4_doppler integer

[-32768, 32767]

 
Provide Loc Info Gnss Sat Measure Element 4 Adr provide_loc_info_gnss_sat_meas_elem_4_adr integer [0, 33554431]  












5
The parameters for the 5th GNSS-SatMeasElement in gnss-SgnMeasList:
Provide Loc Info Gnss Sat Measure Element 5 Carrier Quality Ind present provide_loc_info_gnss_sat_meas_elem_5_carr_qa_ind_present      
Provide Loc Info Gnss Sat Measure Element 5 Integer Code Phase present provide_loc_info_gnss_sat_meas_elem_5_int_code_phase_present      
Provide Loc Info Gnss Sat Measure Element 5 Doppler present provide_loc_info_gnss_sat_meas_elem_5_doppler_present      
Provide Loc Info Gnss Sat Measure Element 5 ADR present provide_loc_info_gnss_sat_meas_elem_5_adr_present      
Provide Loc Info Gnss Sat Measure Element 5 Sat Id provide_loc_info_gnss_sat_meas_elem_5_sat_id integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 5 cNo provide_loc_info_gnss_sat_meas_elem_5_cno integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 5 mpath Det provide_loc_info_gnss_sat_meas_elem_5_mpatch_det integer [0, 3] 0 for notMeasured, 1 for low, 2 for medium, 3 for high.
Provide Loc Info Gnss Sat Measure Element 5 Code Phase RMS Error provide_loc_info_gnss_sat_meas_elem_5_code_phase_rms_err integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 5 Code Phase provide_loc_info_gnss_sat_meas_elem_5_code_phase integer [0, 2097151]  
Provide Loc Info Gnss Sat Measure Element 5 Carrier Quality Ind provide_loc_info_gnss_sat_meas_elem_5_carr_qa_ind integer [0, 3]  
Provide Loc Info Gnss Sat Measure Element 5 Integer Code Phase provide_loc_info_gnss_sat_meas_elem_5_int_code_phase integer [0, 127]  
Provide Loc Info Gnss Sat Measure Element 5 Doppler provide_loc_info_gnss_sat_meas_elem_5_doppler integer

[-32768, 32767]

 
Provide Loc Info Gnss Sat Measure Element 5 Adr provide_loc_info_gnss_sat_meas_elem_5_adr integer [0, 33554431]  












6
The parameters for the 6th GNSS-SatMeasElement in gnss-SgnMeasList:
Provide Loc Info Gnss Sat Measure Element 6 Carrier Quality Ind present provide_loc_info_gnss_sat_meas_elem_6_carr_qa_ind_present      
Provide Loc Info Gnss Sat Measure Element 6 Integer Code Phase present provide_loc_info_gnss_sat_meas_elem_6_int_code_phase_present      
Provide Loc Info Gnss Sat Measure Element 6 Doppler present provide_loc_info_gnss_sat_meas_elem_6_doppler_present      
Provide Loc Info Gnss Sat Measure Element 6 ADR present provide_loc_info_gnss_sat_meas_elem_6_adr_present      
Provide Loc Info Gnss Sat Measure Element 6 Sat Id provide_loc_info_gnss_sat_meas_elem_6_sat_id integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 6 cNo provide_loc_info_gnss_sat_meas_elem_6_cno integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 6 mpath Det provide_loc_info_gnss_sat_meas_elem_6_mpatch_det integer [0, 3] 0 for notMeasured, 1 for low, 2 for medium, 3 for high.
Provide Loc Info Gnss Sat Measure Element 6 Code Phase RMS Error provide_loc_info_gnss_sat_meas_elem_6_code_phase_rms_err integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 6 Code Phase provide_loc_info_gnss_sat_meas_elem_6_code_phase integer [0, 2097151]  
Provide Loc Info Gnss Sat Measure Element 6 Carrier Quality Ind provide_loc_info_gnss_sat_meas_elem_6_carr_qa_ind integer [0, 3]  
Provide Loc Info Gnss Sat Measure Element 6 Integer Code Phase provide_loc_info_gnss_sat_meas_elem_6_int_code_phase integer [0, 127]  
Provide Loc Info Gnss Sat Measure Element 6 Doppler provide_loc_info_gnss_sat_meas_elem_6_doppler integer

[-32768, 32767]

 
Provide Loc Info Gnss Sat Measure Element 6 Adr provide_loc_info_gnss_sat_meas_elem_6_adr integer [0, 33554431]  












7
The parameters for the 7th GNSS-SatMeasElement in gnss-SgnMeasList:
Provide Loc Info Gnss Sat Measure Element 7 Carrier Quality Ind present provide_loc_info_gnss_sat_meas_elem_7_carr_qa_ind_present      
Provide Loc Info Gnss Sat Measure Element 7 Integer Code Phase present provide_loc_info_gnss_sat_meas_elem_7_int_code_phase_present      
Provide Loc Info Gnss Sat Measure Element 7 Doppler present provide_loc_info_gnss_sat_meas_elem_7_doppler_present      
Provide Loc Info Gnss Sat Measure Element 7 ADR present provide_loc_info_gnss_sat_meas_elem_7_adr_present      
Provide Loc Info Gnss Sat Measure Element 7 Sat Id provide_loc_info_gnss_sat_meas_elem_7_sat_id integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 7 cNo provide_loc_info_gnss_sat_meas_elem_7_cno integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 7 mpath Det provide_loc_info_gnss_sat_meas_elem_7_mpatch_det integer [0, 3] 0 for notMeasured, 1 for low, 2 for medium, 3 for high.
Provide Loc Info Gnss Sat Measure Element 7 Code Phase RMS Error provide_loc_info_gnss_sat_meas_elem_7_code_phase_rms_err integer [0, 63]  
Provide Loc Info Gnss Sat Measure Element 7 Code Phase provide_loc_info_gnss_sat_meas_elem_7_code_phase integer [0, 2097151]  
Provide Loc Info Gnss Sat Measure Element 7 Carrier Quality Ind provide_loc_info_gnss_sat_meas_elem_7_carr_qa_ind integer [0, 3]  
Provide Loc Info Gnss Sat Measure Element 7 Integer Code Phase provide_loc_info_gnss_sat_meas_elem_7_int_code_phase integer [0, 127]  
Provide Loc Info Gnss Sat Measure Element 7 Doppler provide_loc_info_gnss_sat_meas_elem_7_doppler integer

[-32768, 32767]

 
Provide Loc Info Gnss Sat Measure Element 7 Adr provide_loc_info_gnss_sat_meas_elem_7_adr integer [0, 33554431]  

 

 

Tcl Parameter: LppSrvOriginHostCfgFileEn

Tcl Parameter: LppClnOriginHostCfgFileEn

 

See About Applying Parameter ValuesAbout Applying Parameter Values.

See Test Data Files for further explanation and sample files. If a sample is not found for the specific TDF, you can obtain a sample file from your Technical Support representative. You may also use the following options to select an existing TDF or create/edit TDF-CSV files (TDF-CSV Editor). 

For most TDF Parameters used for Applying Parameters, each row in the file is the overridden value for a different “Session”, aka a different UE. But some TDFs are done in other dimensions, like Bearers, eNodeBs, Subscribers (2 per UE sometimes) or even Hosts, etc. Tooltips on the TDF Parameter: 

Note that the “ID” is a unique ID. Please Provide the ID when reporting issues with a TDF. For TDFs that do not apply / override Parameters, but instead are just their own configuration or data or media files you won’t see TDF ID row details.

TIP: When including large files, please be aware of memory limitations, since the TDF Editor shares memory with the Client.

NOTE: The available TDF options vary. on the L3-7 | IPSec tab > IKE with RSA Settings you may only select the Certificate TDF from TAS (these are non-CSV TDFs).

In addition, where applicable, any rules for defining TDFs are included in specific Test Cases. (For example, In MME Node test case, see MME Node - Provisioning TDF.)

From the DMF Window, press Shift+Alt+A to display the  Save DMF as Tcl window. Click the Save to File button to save as Tcl file. See additional details on Using the Tcl API.

 

Select/Create a new TDF-CSV

Allows you to create a new TDF by entering a file name that doesn’t already exist or select an existing file by entering a file name that already exists.

Click to open the Select Existing or Create window.

  • Navigate to the relevant library/folder,

  • Enter the name of the file:

  • If the file name already exists, the file is selected and applied in the test case.

  • If the file name does not exist, a message displays that says you are creating a new TDF and the embedded TDF-CSV will be launched.

    • Click Yes to launch the TDF-CSV Editor and create/save the new TDF-CSV.

    • Click No to select a different file

NOTE: If you do not have permission to save in the selected library, an error displays when you try to create a new file.
TIP: You may also navigate to the relevant library/folder and select file, and click OK.

 

Upload a New TDF to TAS

Click to import a new TDF file from your local folder and select in the test Case (instead of having to go to TDF Admin).

  • Navigate to the file on your local folder and select.
  • Then navigate to the location (library) where you want to save it on the TAS. You may rename the file, if required.  

View Edit Selected TDF in TDF-CSV Editor

Available only when you have selected a TDF on TAS. Click to open the selected file in TDF-CSV Editor (in place, that is, within the Test Case).

Edit the file and save. You may also click Save As to save the edited TDF-CSV to a different library and also rename the file, if required.

NOTE: You may also select a TDF from a library to which you do not have write permissions, edit the file as required, and save (Save As) only to a different library with the same file name or a different name.

The only options available are Save As and Cancel.

Open Selected TDF in Standalone TDF-CSV Editor

Available only when you have selected a TDF on TAS. Select to retrieve the CSV file and open it in the stand alone TDF-CSV Editor.

Generate Stub TDF-CSV

TIP: Available only when a CSV specification has been defined for in the Test Case for the TDF widget ( View TDF Actions/Options Menu)

 

Opens an example context specific test data parametersexample context specific test data parameters, which you may save as a .CSV file or open in the TDF-CSV Editor.

 

Launch Standalone TDF-CSV Editor

Click to open a blank TDF-CSV Editor.

The Launch Standalone TDF-CSV editor options handles very large TDFs that may use too much Client memory if opened within the Test Case/in the embedded editor.  You may set the standalone TDF-CSV Editor memory high to edit large TDFs.

 

Client - Location Estimate

Location Estimate

Select to include Location Estimate information for the Provide Location Info message. Available in several test cases including IP Application Node when Data Protocol ulp is selected in Data Message Flow.

TDF Parameter Name : Provide Loc Info Loc Estimate Present

Tcl Parameter: LppClnLocEstimate

Coordinate Type

Use the drop-down list to select the coordinate type for the Location Estimate chosen. The applicable parameters are enabled based on your selection.

Options:

  • Ellipsoid Point

  • Ellipsoid Point With Uncertainty Circle

  • Ellipsoid Point With Uncertainty Ellipse

  • Polygon

  • Ellipsoid Point With Altitude

  • Ellipsoid Point With Altitude And Uncertainty Ellipsoid

  • Ellipsoid Arc

Default: Ellipsoid Point

TDF Parameter Name : Provide Loc Info Loc Estimate Chosen

Tcl Parameter: LppClnLocEstCoordinateType

Latitude Sign

Use the drop-down list to select the Latitude Sign for the Location Estimate chosen.

Options:

  • north

  • south

TDF Parameter Name : Provide Loc Info Latitude Sign - TDF sets as 0 (north)/ 1 (south). 

Example: 

Tcl Parameter: LppClnLocEstLatitudeSign

Latitude Degree 

Available for all Coordinate Types except Polygon.

Enter Latitude point coordinate. GUI and TDF require the raw values to be input. User must encode the inputs to match the desired latitude and longitude - per 3GPP Spec 23.032 on Universal Geographic Area Description (GAD).  

Range : 0 to 8388607

Default: 0

TDF Parameter Name : Provide Loc Info Degrees Latitude 

Example:  

Tcl Parameter: LppClnLocEstLatitudeDegree

Longitude Degree 

Available for all Coordinate Types except Polygon.

Enter Longitude point coordinate. GUI and TDF require the raw values to be input. User must encode the inputs to match the desired latitude and longitude  - per 3GPP Spec 23.032 on Universal Geographic Area Description (GAD).  

Range : -8388608 to 8388607

Default: 0

TDF Parameter Name : Provide Loc Info Degrees Longitude

Tcl Parameter: LppClnLocEstLongitudeDegree

Altitude Direction

Available when Coordinate Type = Ellipsoid Point with Altitude or Ellipsoid Point With Altitude and Uncertainty Ellipsoid.

Select the Altitude direction.

Options : height, depth

TDF Parameter Name : Provide Loc Info Altitude Direction

Tcl Parameter: LppClnLocEstAltitudeDirection

Altitude (m)

Available when Coordinate Type = Ellipsoid Point with Altitude or Ellipsoid Point With Altitude and Uncertainty Ellipsoid.

Enter the Altitude in meters.

Range : 0 to 32767

Default: 0

TDF Parameter Name : Provide Loc Info Altitude

Tcl Parameter: LppClnLocEstAltitude

Uncertainty (m)

Available when Coordinate Type = Ellipsoid Point With Uncertainty Circle.

Enter the uncertainty for Point Uncertainty Circle in meters.

Range : 0 to 127

Default: 0

TDF Parameter Name : Provide Loc Info Uncertainty Factor

Tcl Parameter: LppClnLocEstUncertainty

Uncertainty Semi Major (m)

Uncertainty Semi Minor (m)

Uncertainty Orientation  (m)

Orientation Major Axis (°)

Available when Coordinate Type = Ellipsoid Point with Uncertainty Ellipse or Ellipsoid Point With Altitude and Uncertainty Ellipsoid.

Enter the Uncertainty Semi Major and Semi Minor in meters.

Range : 0 to 127

Default: 0

TDF Parameter Name : Provide Loc Info Uncertainty Semi Major

TDF Parameter Name : Provide Loc Info Uncertainty Semi Minor

Tcl Parameter: LppClnLocEstUncertaintySemiMajor

Tcl Parameter: LppClnLocEstUncertaintySemiMinor

 

Enter the Orientation Major Axis (°) in degrees.

Range : 0 to 179

Default: 0

Tcl Parameter: LppClnLocEstOrientationMajorAxis

Confidence (%)

Available when Coordinate Type = Ellipsoid Point with Uncertainty Ellipse or Ellipsoid Point With Altitude and Uncertainty Ellipsoid or Ellipsoid Arc.

Enter the Confidence in percentage value.

Range : 0 to 100

Default: 0

TDF Parameter Name : Provide Loc Info Confidence

Tcl Parameter: LppClnLocEstConfidence

Uncertainty Altitude (m)

Available when Coordinate Type = Ellipsoid Point With Altitude and Uncertainty Ellipsoid

Enter the Uncertainty Altitude in meters.

Range : 0 to 127

Default: 0

TDF Parameter Name : Provide Loc Info Uncertainty Altitude.

Tcl Parameter: LppClnLocEstUncertaintyAltitude

Arc Settings

Inner Radius (m)

Uncertainty Radius (m)

Offset Angle

Included Angle

Available when Coordinate Type = Ellipsoid Arc.

Enter the Inner Radius in meters.

Range : 0 to 65535

Default: 0

TDF Parameter Name : Provide Loc Info Inner Radius.

Tcl Parameter: LppClnLocEstInnerRadius

Enter the Uncertainty Radius in meters.

Range : 0 to 127

Default: 0

TDF Parameter Name : Provide Loc Info Uncertainty Radius.

Tcl Parameter: LppClnLocEstUncertaintyRadius

Enter the Offset Angle and Included Angle.

Range : 0 to 179

Default: 0

TDF Parameter Name : Provide Loc Info Offset Angle.

TDF Parameter Name : Provide Loc Info Included Angle.

Tcl Parameter: LppClnLocEstOffsetAngle

Tcl Parameter: LppClnLocEstIncludedAngle

Polygon

Available when Coordinate Type = Polygon.

Enter the Number of Points.

Range : 3 to 15

Default: 3

Tcl Parameter: LppClnLocEstPointNum

Enter the Latitude Sign (north,south) , Latitude (Range : 0 to 8388607) and Longitude (Range : -8388608 to 8388607) for each Point.

Tcl Parameter: LppClnEstPolygonLatitudeSign_1

Tcl Parameter: LppClnEstPolygonLatitudeDegree_1

Tcl Parameter: LppClnLocEstLongitudeDegree_1

Client - Velocity Estimate

Velocity Estimate

Select to include Velocity Estimate information for the Provide Location Info message. Available in several test cases including IP Application Node when Data Protocol ulp is selected in Data Message Flow.

TDF Parameter Name : Provide Loc Info Velocity Estimate Present

Tcl Parameter: LppClnVelocityEstimate

Type

Use the drop-down list to select the coordinate type for the Velocity Estimate chosen. The applicable parameters are enabled based on your selection.

Options:

  • Horizontal Velocity

  • Horizontal With Vertical Velocity

  • Horizontal Velocity With Uncertainty

  • Horizontal With Vertical Velocity And Uncertainty

Default: Horizontal Velocity

TDF Parameter Name : Provide Loc Info Velocity Estimate Chosen

Tcl Parameter: LppClnVelEstType

Bearing (°)

Available for all Types.

Enter bearing in (°) degrees.

Range : 0 to 359

Default: 0

TDF Parameter Name : Provide Loc Info Bearing

Tcl Parameter: LppClnVelEstBearing

Horizontal Speed (km/h)

Available for all Types.

Enter the Horizontal Speed in Kilometers per Hour.

Range : 0 to 2047

Default: 0

TDF Parameter Name : Provide Loc Info Horizontal Speed

Tcl Parameter: LppClnVelEstHorizontalSpeed

Vertical Direction

Available when Type = Horizontal With Vertical Velocity or Horizontal With Vertical Velocity And Uncertainty.

Select the Vertical direction.

Options : upward, downward

TDF Parameter Name : Provide Loc Info Vertical direction

Tcl Parameter: LppClnVelEstVerticalDirection

Vertical Speed (km/h)

Available when Type = Horizontal With Vertical Velocity or Horizontal With Vertical Velocity And Uncertainty.

Enter the Vertical Speed in Kilometers per Hour.

Range : 0 to 255

Default: 0

TDF Parameter Name : Provide Loc Info Vertical Speed

Tcl Parameter: LppClnVelEstVerticalSpeed

Uncertainty Speed (km/h)

Available when Type = Horizontal Velocity with Uncertainty.

Enter the Uncertainty Speed in Kilometers per Hour.

Range : 0 to 255

Default: 0

TDF Parameter Name : Provide Loc Info Uncertainty Speed

Tcl Parameter: LppClnVelEstUncertaintySpeed

Horizontal Uncertainty Speed (km/h)

Available when Type = Horizontal with Vertical Velocity And Uncertainty.

Enter the Horizontal Uncertainty Speed in Kilometers per Hour.

Range : 0 to 255

Default: 0

TDF Parameter Name : Provide Loc Info Horizontal Uncertainty Speed

Tcl Parameter: LppClnVelEstHorizontalUncertaintySpeed

Vertical Uncertainty Speed (km/h)

Available when Type = Horizontal with Vertical Velocity And Uncertainty.

Enter the Vertical Uncertainty Speed in Kilometers per Hour.

Range : 0 to 255

Default: 0

TDF Parameter Name : Provide Loc Info Vertical Uncertainty Speed

Tcl Parameter: LppClnVelEstVerticalUncertaintySpeed

Client - Location Error

Location Error

Use the drop-down to select a Failure Cause for the Location Error in Provide Location Info Message.

Options:

  • Undefined

  • Requested Method Not Supported

  • Position Method Failure

  • Periodic Location Measurements Not Available

Default: Undefined

TDF Parameter Name : Provide Loc Info Loc Error Present, Provide Loc Info Loc Failure Cause

Tcl Parameter: LppClnLocError

Tcl Parameter: LppClnLocErrorFailureCause

Client - Message Payload

Provide Capabilities Payload

Select to provide the Capabilities Payload.

Range : Hex character string with prefix “0x”. Maximum string length: 4096 (including the prefix "0x").

TDF Parameter Name : Provide CAP Payload

Tcl Parameter: LppClnProvideCapPayloadEn

Tcl Parameter: LppClnProvideCapPayload

Provide Location Info Payload

Select to provide the Location Info Payload.

Range : Hex character string with prefix “0x”. Maximum string length: 4096 (including the prefix "0x").

TDF Parameter Name : Provide Loc Info Payload

Tcl Parameter: LppClnProvideLocInfoPayloadEn

Tcl Parameter: LppClnProvideLocInfoPayload

Request Assistance Data Payload

Select to Request Assistance Data Payload.

Range : Hex character string with prefix “0x”. Maximum string length: 4096 (including the prefix "0x").

TDF Parameter Name : Req AD Payload

Tcl Parameter: LppClnReqAdPayloadEn

Tcl Parameter: LppClnReqAdPayload

 

Server - Message Payload

Request Capabilities Payload

Select to Request the Capabilities Payload.

Range : Hex character string with prefix “0x”. Maximum string length: 4096 (including the prefix "0x").

TDF Parameter Name : Provide CAP Payload

Tcl Parameter: LppSrvReqCapPayloadEn

Tcl Parameter: LppSrvReqCapPayload

Request Location Info Payload

Select to Request the Location Info Payload.

Range : Hex character string with prefix “0x”. Maximum string length: 4096 (including the prefix "0x").

TDF Parameter Name : Provide Loc Info Payload

Tcl Parameter: LppSrvReqLocInfoPayloadEn

Tcl Parameter: LppSrvReqLocInfoPayload

Provide Assistance Data Payload

Select to Provide Assistance Data Payload.

Range : Hex character string with prefix “0x”. Maximum string length: 4096 (including the prefix "0x").

TDF Parameter Name : Req AD Payload

Tcl Parameter: LppSrvProvideAdPayloadEn

Tcl Parameter: LppSrvProvideAdPayload

 

Request Position Info

Request Position Info

Select to Request Position Information. The Request Position Pane becomes available for input. When it is checked,  UE shall perform the MO-LR service procedure for requesting location-estimate of UE. 

Select for AMF Nodal support for 5GC-MO-LR Procedure (3GPP TS 23.273 Clause 6.2).

AMF-NODAL test case for supporting the 5GC Mobile-Originating Location-Request (5GC-MO-LR) procedure listed in the clause 6.2 of 3GPP TS 23.273. The following figure 1.1A  shows the overview of the 5GC-MO-LR procedure:

Spec References: 3GPP TS 23.273 V17.10 (2021-06)

Limitations:

  • MO-LR service does NOT request for location-assistance data. 
  • MO-LR service does NOT request for sending location-estimate of UE to an external LCS-Client or AF.
  • MO-LR service does NOT support event-reporting.

Tcl Parameter: LppClnReqPosInfoEn

Start Time (s)

Timer T(LCSL) (s)

Available when Request Position Info is enabled.

Enter the Start Time (s)  in seconds for Request Position.

Range : 0 to 65525

Default : 5 seconds

Enter the Timer T (LCSL) (s) in seconds for Request Position. This timer is used by UE for releasing service-request if it doesn't get a location-response from LCS within a specific time.

Range : 10 to 300

Default : 30 seconds

Tcl Parameter: LppClnReqPosStartTime

Tcl Parameter: LppClnReqPosTimerTlcsl

LCS Client Type

Select the LCS Client Type. Available when Request Position Info is enabled.

Options : EMERGENCY SERVICES, VALUE ADDED SERVICES, PLMN OPERATOR SERVICES, LAWFUL INTERCEPT SERVICES, PLMN OPERATOR BROADCAST SERVICES, PLMN OPERATOR OM, PLMN OPERATOR ANONYMOUS STATISTICS, PLMN OPERATOR TARGET MS SERVICE SUPPORT

Tcl Parameter: LppClnLcsCliType

LCS Location

Select the LCS Location. Available when Request Position Info is enabled.

Options : CURRENT LOCATION, CURRENT OR_LAST KNOWN LOCATION, INITIAL LOCATION

Tcl Parameter: LppClnLcsLoc

LCS Supported GAD Shapes

Select the LCS Supported GAD Shapes for input pane to allow selection of the following supported shapes.

Options : POINT, POINT UNCERTAINTY CIRCLE, POINT UNCERTAINTY ELLIPSE, POLYGON, POINT ALTITUDE, POINT ALTITUDE UNCERTAINTY, ELLIPSOID ARC

Tcl Parameter: LppClnLcsSupGADShapesEn

Tcl Parameter: LppClnLcsSupGADShapes

Location QoS

Select Location QoS and the Location details. Available when Request Position Info is enabled.

Tcl Parameter: LppClnLcsQosEn

Horizontal Accuracy  

Select to enter the Horizontal Accuracy.

Range : 0 to 1.7976931348623157E308

Default: 0.5

Tcl Parameter: LppClnHorAccEn

Tcl Parameter: LppClnHorAcc

Vertical Accuracy

Select to enter the Vertical Accuracy.

Range : 0 to 1.7976931348623157E308

Default: 0.5

Tcl Parameter: LppClnVerAccEn

Tcl Parameter: LppClnVerAcc

Vertical Accuracy Requested

Select to indicate Vertical Accuracy requested.

Options : No , Yes

Tcl Parameter: LppClnVerAccReqEn

Tcl Parameter: LppClnVerAccReq

Response Time

Select to indicate Response Time.

Options : LOW_DELAY (default), DELAY_TOLERANT

Tcl Parameter: LppClnRespTimeEn

Tcl Parameter: LppClnRespTime

Velocity Requested

Select to enter the Velocity Requested.

Options : VELOCITY_IS_NOT_REQUESTED (Default), VELOCITY_IS_REQUESTED,

Tcl Parameter: LppClnVelReqEn

Tcl Parameter: LppClnVelReq

 

 

Support Request Position Info from On-Demand Command

Available on LMF Interface on AMF node test case when Command Mode is enabled.

The ODC on AMF Node's AMF-LMF tab is named "ControlLcs" - Command Mode AMF Node . It will be available in the running state when in Command Mode and "Support Request Position Info from On-Demand Command" is checked.

Tcl Parameter: LppOdcReqPosInfoEn

WLAN-based Positioning

WLAN-based Positioning

Enable WLAN based positioning. Available in Service Based Node test case when LMF (Nlmf) is enabled.

Tcl Parameter: LppWlanEn

Requested Measurements

Select Received Signal Strength Indicator (RSSI) and / or Round Trip Time (RTT) requested measurements.

Tcl Parameter: LppWlanReqRssiEn

Tcl Parameter: LppWlanReqRttEn

Assistance Data

Select Number of Data Sets.

Range : 0 to 8

Default : 0

Tcl Parameter: LppWlanDataSetNum

For each Data Set, Select the number of Access Points - Select AP Num. Enter the AP pane information.

Range : 1 to 10

Default : 1

Tcl Parameter: LppWlanDataSetApNum_1

BSSID

Enter the BSSID (the MAC address of the wireless access point).

Range: 12 HEX Characters

Default : 02004C4F4F50

Tcl Parameter: LppWlanDataSetApBssid_1_1

SSID

Enter the SSID (the service set identifier).

Range: up to 32 Characters

Tcl Parameter: LppWlanDataSetApSsid_1_1

Ap Location

Select to enter the Ap location data.

Tcl Parameter: LppWlanDataSetApLocEn_1_1

Latitude

Enter the Latitude of the Ap location in degrees (°).

Range : 0 to 17179869183

Default: 0

Tcl Parameter: LppWlanDataSetApLatitude_1_1

Latitude Uncertainty

Enter the Latitude Uncertainty of the Ap location in degrees (°).

Range : 0 to 34

Default: 0

Tcl Parameter: LppWlanDataSetApLatitudeUn_1_1

Longitude

Enter the Longitude of the Ap location in degrees (°).

Range : 0 to 17179869183

Default: 0

Tcl Parameter: LppWlanDataSetApLongitude_1_1

Longitude Uncertainty

Enter the Longitude Uncertainty of the Ap location in degrees (°).

Range : 0 to 34

Default: 0

Tcl Parameter: LppWlanDataSetApLongitudeUn_1_1

Altitude

Select to enter the Altitude of the Ap location in meters (m).

Range : 0 to 1073741823

Default: 0

Tcl Parameter: LppWlanDataSetApAltitudeEn_1_1

Tcl Parameter: LppWlanDataSetApAltitude_1_1

Altitude Uncertainty

Select to enter the Altitude Uncertainty of the Ap location in degrees (°).

Range : 0 to 30

Default: 0

Tcl Parameter: LppWlanDataSetApAltitudeUnEn_1_1

Tcl Parameter: LppWlanDataSetApAltitudeUn_1_1

Map Datum

Select a Map Datum (a model of the earth that is used in mapping).

Options  : WGS-84, NAD-83 with NAVD-88 , NAD-83 with MLLW

Tcl Parameter: LppWlanDataSetApMapDatumWgs_1_1

Tcl Parameter: LppWlanDataSetApMapDatumNavd_1_1

Tcl Parameter: LppWlanDataSetApMapDatumMllw_1_1

 

Supported Channels 11a

Select Supported Channels 11a to enable Channel # in the 11a group.

Channel # supported : 34, 36, 38, 40, 42, 44, 46, 48, 52, 56, 60, 64, 149, 153, 157, 161

Tcl Parameter: LppWlanDataSet11aChanEn_1

Tcl Parameter: LppWlanDataSet11aChan34En_1

Tcl Parameter: LppWlanDataSet11aChan36En_1

Tcl Parameter: LppWlanDataSet11aChan38En_1

Tcl Parameter: LppWlanDataSet11aChan40En_1

Tcl Parameter: LppWlanDataSet11aChan42En_1

Tcl Parameter: LppWlanDataSet11aChan44En_1

Tcl Parameter: LppWlanDataSet11aChan46En_1

Tcl Parameter: LppWlanDataSet11aChan48En_1

Tcl Parameter: LppWlanDataSet11aChan52En_1

Tcl Parameter: LppWlanDataSet11aChan56En_1

Tcl Parameter: LppWlanDataSet11aChan60En_1

Tcl Parameter: LppWlanDataSet11aChan64En_1

Tcl Parameter: LppWlanDataSet11aChan149En_1

Tcl Parameter: LppWlanDataSet11aChan153En_1

Tcl Parameter: LppWlanDataSet11aChan157En_1

Tcl Parameter: LppWlanDataSet11aChan161En_1

Supported Channels 11bg

Select Supported Channels 11bg to enable Channel # in the 11bg group.

Channel # supported : 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14

Tcl Parameter: LppWlanDataSet11bgChanEn_1

Tcl Parameter: LppWlanDataSet11bgChan1En_1

Tcl Parameter: LppWlanDataSet11bgChan2En_1

Tcl Parameter: LppWlanDataSet11bgChan3En_1

Tcl Parameter: LppWlanDataSet11bgChan4En_1

Tcl Parameter: LppWlanDataSet11bgChan5En_1

Tcl Parameter: LppWlanDataSet11bgChan6En_1

Tcl Parameter: LppWlanDataSet11bgChan7En_1

Tcl Parameter: LppWlanDataSet11bgChan8En_1

Tcl Parameter: LppWlanDataSet11bgChan9En_1

Tcl Parameter: LppWlanDataSet11bgChan10En_1

Tcl Parameter: LppWlanDataSet11bgChan11En_1

Tcl Parameter: LppWlanDataSet11bgChan12En_1

Tcl Parameter: LppWlanDataSet11bgChan13En_1

Tcl Parameter: LppWlanDataSet11bgChan14En_1

 

^ Back to Top