The values on the BBERF Session tab report the Credit Control measurements for the PCRF Nodal and PCRF Node test cases (between the AGW and PCRF over Gxc interface).
In the default view, the Reports tab displays the Summary view, which summarizes the measurements for the test session. If your test includes multiple test cases, you can view the report for a single test case by changing the report view...
Unless otherwise noted, cumulative values report the number of occurrences or rates calculated since the start of the test, and per-interval values report the number of occurrences or rates calculated during the interval. You can view either by changing the measurement values...
Elapsed Time is the first measurement on every tab. It reports the amount of time between the start of the test and the end of the report interval.
Test Iteration reports the current iteration in a repeating test session. It is only displayed when a Number of Iterations is defined for the test session.
The following measurements record the number and types of messages exchanged between the BBERF and the AGW and the average response time when a response is expected.
CCR Received — The number of CCRs received from the BBERF node.
CCR Initial Received — The number of initial CCRs sent by the BBERF node.
CCR Updates Received — The number of update CCRs received by the BBERF node.
CCR Term Received — The number of terminate CCRs received by the BBERF node.
CCA Sent — The number of CCAs sent to the BBERF node.
CCA Initials Rcvd — The number of CCA Initials received from the BBERF node.
CCA Updates Rcvd — The number of CCA Updates received from the BBERF node.
CCA Term Rcvd — The number of CCA Terminate received from the BBERF node.
RAR Sent — The number of RARs sent to the BBERF.
RAA Received — The number of RAAs received by the BBERF (from the PCRF) in acknowledgement of the RAR.
RAR Timeout — The number of times the Wait Response Time expired while waiting for an answer to a RAR.
Unknown User — The number of times a CCR was received that contained an unknown MSISDN.
Poorly Formed Requests — The number of transactions that failed because the SUT's answer message could not be parsed.
Average RAR Response — The number of RARs received at the BBERF node.
Send Error — The number of errors encounters during send operation.
SGSN Changes — Indicates that the serving SGSN has changed, hence PCC rules is being requested. When used in a CCR command, this value indicates that the PCEF generated the request because the serving SGSN changed.
QoS Changes — Indicate that PCC Rules are requested at bearer or APN as a result of QoS change (even within the limits of the current authorization).
When used in a CCR command, this value indicates that the PCEF generated the request because there has been a change in the requested QoS for a specific bearer (e.g., the previously maximum authorized QoS has been exceeded) or APN. The Bearer-Identifier AVP indicates the affected bearer.
QoS-Information AVP is required to be provided in the same request with the new value. When applicable at APN level, this event trigger is reported when the corresponding event occurs, even if the event trigger is not provisioned by the PCRF.
RAT Changes — Indicates that PCC rules are requested as a result of a RAT change.
When used in a CCR command, this value indicates that the PCEF generated the request because of a RAT change. The new RAT type is provided in the RAT-Type AVP. RAT Change (2)
TFT Changes — Indicates that PCC rules are requested as a result of a TFT change.
When used in a CCR command, this value indicates that the PCEF generated the request because of a change in the TFT. The Bearer-Identifier AVP is provided to indicate the affected bearer. All the TFT values for this bearer is provided in TFT-Packet-Filter-Information AVP.
This event trigger shall be provisioned by the PCRF at the PCEF. Applicable only to 3GPP-GPRS.
Loss of Bearers — Indicates the loss of bearer (GW informs PCRF).
When used in a CCR command, this value indicates that the PCEF generated the request because the bearer associated with the PCC rules indicated AVP was lost (in the corresponding Charging-Rule-Report). The PCC-Rule-Status AVP within the Charging-Rule-Report AVP indicates that these PCC rules are temporarily inactive.
Recovery of Bearers — Indicates that recovery of bearer (GW informs PCRF).
When used in a CCR command, this value indicates that the PCEF generated the request because the bearer associated with the PCC rules indicated by the corresponding Charging-Rule-Report AVP was recovered. The PCC-Rule-Status AVP within the Charging-Rule-Report AVP indicates that these rules are active again.
RAI Changes — Indicates that upon a change in the RAI, PCEF shall inform the PCRF.
When used in a CCR command, this value indicates that the PCEF generated the request due to a change in the RAI. The new RAI value is provided in the RAI AVP. (If the user location has been changed but the PCEF cannot get the detail location information (e.g. handover from 3G to 2G network), the PCEF shall send the RAI AVP to the PCRF by setting the LAC of the RAI to value 0x0000. Applicable only to 3GPP-GPRS and 3GPP-EPS access types).
User Location Changes — Indicates a change in the user location (i.e., applicable for CGI/SAI/RAI/TAI/ECGI - PCEF informs the PCRF).
When used in a CCR command, this value indicates that the PCEF generated the request due to a change in the user location. The new location value is provided in the 3GPP-User-Location-Info AVP.
No Event Triggers — Indicates that PCRF does not require any Event Trigger notification except for those events that do not require subscription and are always provisioned.
Revalidation Timeouts — Indicates PCC revalidation timeout (PCEF informs the PCRF).
When used in a CCR command, this value indicates that the PCEF generated the request because there has been a PCC revalidation timeout.
Default EPS Bearer QoS Changes — Indicates change in the default EPS Bearer QoS (PCEF informs the PCRF). When used in a CCR command, this value indicates that the PCEF generated the request due to a change in the default EPS Bearer QoS.
Successful Resource Allocations — Indicates successful resource allocation for the required rules (PCEF informs the PCRF).
When used in a CCR or RAA command, this value indicates that the PCEF informs the PCRF that the resources for a rule have been successfully allocated.
UE Time Zone Changes — Indicates that PCC rules are requested because the current UE location time zone has changed.
When used in a CCR command, this value indicates that the PCEF generated the PCC rules request because the current UE location time zone has changed. (The new value of the UE’s time zone is indicated in the 3GPP-MS-TimeZone AVP).
Usage Reports — Used in a CCR to indicate that the PCEF generated the request to report the accumulated usage for one or more monitoring keys.
The PCEF also provides the accumulated usage volume using the Usage-Monitoring-Information AVP(s) including the Monitoring-Key AVP and the Used-Service-Unit AVP.
TAI Changes — Used in a CCR to indicate that the PCEF generated the request because of a change in the TAI.
eCGI Changes — Indicates that the PCEF generated the request due to a change in the ECGI.
When used in a CCR, the value indicates that the PCEF generated the request due to a change in the ECGI. The new ECGI value is provided in the 3GPP-User-Location-Info AVP.
Charging Correlation Exchanges — Indicates that the PCEF reports the access network charging identifier has been assigned (associated to one or more dynamic PCC Rules within the Access-Network-Charging-Identifier-Gx AVP).
User CSG Information Changes — Indicates that the User CSG Information has changed (CSG membership in hybrid access mode has changed, or user entering/leaving a CSG cell).
User CSG Hybrid Subscribed Information Changes — Indicates a request of reporting an event when the user enters/leaves a subscribed hybrid cell.
When the user enters a hybrid cell where the user is a member, the User-CSG-Information AVP is provided with the event report in the CCR command.
User CSG Hybrid Unsubscribed Information Changes — Indicates a request of reporting an event when the user enters/leaves a unsubscribed hybrid cell.
When the user enters a hybrid cell where the user is not a member, the User-CSG-Information AVP is provided with the event report in the CCR command.
APN-AMBR Modification Failure — Indicates (PCEF to the PCRF) that the APN-AMBR modifications have failed.
The PCEF uses this value in a CCR command to indicate failure of either a PUSH initiated modification or a PULL initiated modification.
Default EPS Bearer QoS Modification Failure — Indicates (PCEF to the PCRF) that the Default EPS Bearer QoS modifications have failed.
The PCEF uses this value in a CCR command to indicate failure of either a PUSH initiated modification or a PULL initiated modification.