Amf to Pcf NF Tab

The Amf to Pcf NF (Network Function) Consumer tab is available when Test PCF (Npcf), From AMF (N15) is selected on Service Based Nodal test case and when N15 Interface is selected on AMF Node test case.

About the 5G Application.

Per 3GPP TS 23.501, 23.502 and 29.5xx.

Service Based Nodal Parameters

NOTE: As of Release 17.6, significant changes were made to this tab in support of the September / December 5G releases. You previous test cases will go red and will require updates.

Related Measurements

Measurements collected for Service Based Node related processing are reported on the AMF-PCF Consumer report tab.

NF Consumer

Npcf Version (29.507)
Use Access Token
- Access Token
Supported Features
Supported Features (for 29.525)
Service Name
Group Identifier
Time Zone
RFSP Index
Include Guami
Home PCF ID

NF Consumer

Access Type

RAT Type
User Location
- Enable User Location
  - MCC
  - MNC
  - TAC
  - NR Cell ID
  - EUTRA Cell ID
  - N3ga IwfId
  - UE IPv4 Address
  - UE IPv6 Address
  - Port Number

UPSI (UE Policy Section Identifier) List

ANDSP Supported by the UE
Number of UPSIs (1 to 4)
- MCC
- MNC
- Number of UPSCs (1 to 8)
  - UPSC

Presence Information

Number of Presence Information (1 to 4)

Presence Information

Number of Presence Information (1 to 4)
- NCGI List
  - Number of NCGI (1 to 4)
    - MCC
    - MNC
    - NR Cell ID
- Global RAN Node ID List
  - Number of Global RAN nodes
    - MCC
    - MNC
    - N3IWF
    - NG RAN Node Type
      - ID

Service Area Restrictions

Number of Service Areas (1 to 16)
Restriction Type
- Only Number of Service Areas
Number of TACs (1 to 16)
- TAC
Number of Area Codes (1 to 16)
- Area Code

New Service Area Restrictions

Number of Service Areas (1 to 16)
Restriction Type
- Only Number of Service Areas
Number of TACs (1 to 16)
- TAC
Number of Area Codes (1 to 16)
- Area Code

UE Policy Delivery Result

Number of Rejected UPSCs
- UPSI
- MCC
- MNC
- UPSC

User Location Change

Time Zone
RAT Type
Access Type

User Location (new)

MCC
MNC
TAC
NR Cell ID
EUTRA Cell ID
N3ga IwfId
UE IPv4 Address
UE IPv6 Address
Port Number

Original Settings / Update Settings

Access Types
- Number of Access Types
  - Access Type
RAT Types
- Number of RAT Types
  - RAT Type
Allowed S-NSSAI
- Number of Allowed S-NSSAIs
  - SST
  - SD
  - SNSSAI HPLMN
  - SST
  - SD
Non-3GPP Allowed S-NSSAI
- Number of Non-3GPP Allowed S-NSSAIs
  - SST
  - SD
  - S-NSSAI HPLMN
  - SST
  - SD

Original Settings / Update Settings

SMF Selection Data
- Unsupported DNN
- DNN
- S-NSSAI
  - SST
  - SD
- Candidates for Replacement
- Number of Candidates
  - SST
  - SD
- Candidate DNNs
  - Number of DNNs
  - DNN

Redirection Settings

Location
Target NF Instance ID

NF Consumer

Available when Test PCF (Npcf), From AMF (N15) is selected on Service Based Nodal test case and when N15 Interface is selected on AMF Node test case on Interface Amf-PCF

Npcf Version (29.507)

Select the Npcf Version.

AMF-PCF, NEF-PCF and SMF-PCF must use the same Npcf Consumer Version.

Options: 15.2.0/Dec2018 (default) , 15.4.0/Jun2019, 16.7.0/Mar2021, 17.7.0/Jun2022

Tcl Parameter: N15NpcfSbiVersion

Use Access Token

Select “Use Access Token” option to support OAuth2 authorization for NF Consumer.

Support for Nnrf_AccessToken Service to the Service Base Nodal /Node NRF per spec TS 29.510 V16.3.0 section 5.4.2.2.1.

Select to enter Access Token. Enter up to 1023 characters

Tcl Parameter: N15NpcfUseAccTokEn

Tcl Parameter: N15NpcfAccTokEn

Tcl Parameter: N15NpcfAccTok

Supported Features

Enter Supported Features.

Unrestricted text field.

Tcl Parameter: N15NpcfSuppFeat

Supported Features (for 29.525)

Enter Supported Features for 29.525.

Unrestricted text field.

Tcl Parameter: N15NpcfUePolSuppFeat

Service Name

Select to enter the Service Name.

Tcl Parameter: N15NpcfIncServingNameEn

Tcl Parameter: N15NpcfIncServingName

Group Identifier

Select to enter Group Identifier.

Unrestricted text field.

Tcl Parameter: N15NpcfGroupIdEn

Tcl Parameter: N15NpcfGroupId

Time Zone

Select to enter Time Zone.

Unrestricted text field.

Tcl Parameter: N15NpcfTimeZoneEn

Tcl Parameter: N15NpcfTimeZone

RFSP Index

Select to enter the RFSP Index (RAT/Frequency selection Priority).

Range: 1 to 256

Default: 1

Tcl Parameter: N15NpcfRfspEn

Tcl Parameter: N15NpcfRfsp

Include Guami

Select to include the Guami (Globally Unique AMF ID).

Tcl Parameter: N15NpcfIncGuamiEn

Home PCF ID

Select to enter the Home PCF ID.

UUID Version 4 format.

Tcl Parameter: N15NpcfHPcfIdEn

Tcl Parameter: N15NpcfHPcfId

Access Type

Select to enter the Access Type.

Options: 3GPP_ACCESS (default), NON_3GPP_ACCESS

Tcl Parameter: N15NpcfAccessTypeEn

Tcl Parameter: N15NpcfAccessType

RAT Type

Select to enter the RAT (Radio Access Technology) Type.

NR = New Radio, EUTRA = Evolved Universal Terrestrial Radio Access

Options: NR (default), EUTRA, WLAN, Virtual

Tcl Parameter: N15NpcfRatTypeEn

Tcl Parameter: N15NpcfRatType

User Location

Enter the User Location.

Select Enable User Location to update the following fields.

Tcl Parameter: N15NpcfUliEn

MCC

MNC

Enter the Mobile Country Code (3 digits) and Mobile Network Code (between two and three digits).

Default: 000

Tcl Parameter: N15NpcfMcc

Tcl Parameter: N15NpcfMnc

TAC

Enter the Tracking Area Code (TAC). Enter 4 to 6 Hex digits.

Tcl Parameter: N15NpcfTac

NR Cell Id

Available if RAT Type = NR (New Radio). Enter the NR Cell Id. Enter up to 9 Hex digits.

Tcl Parameter: N15NpcfNrCellId

EUTRA Cell Id

Available if RAT Type = EUTRA. Enter the EUTRA Cell Id. Enter up to 7 Hex digits.

Tcl Parameter: N15NpcfEutraCellId

N3ga Iwfld UE IPv4 Address UE IPv6 Address Port Number

Available if RAT Type = WLAN or VIRTUAL.

Enter N3ga IwfId. (Non-3GPP Inter-Working Function Identifier). Note: In Release 20.2, this field was changed from unrestricted Text string to 1-128 Hex digits.

Select to enter UE IPv4 Address - Enter a valid IPv4 Address for the UE.

Select to enter UE IPv6 Address - Enter a valid IPv6 Address for the UE.

Select to enter Port Number - Enter a port number. Range: 0 to 65535, Default: 1000

Tcl Parameter: N15NpcfN3iwfId

Tcl Parameter: N15NpcfN3UeIpv4AddrEn

Tcl Parameter: N15NpcfN3UeIpv4Addr

Tcl Parameter: N15NpcfN3UeIpv6AddrEn

Tcl Parameter: N15NpcfN3UeIpv6Addr

Tcl Parameter: N15NpcfN3PortNumberEn

Tcl Parameter: N15NpcfN3PortNumber

UPSI (UE Policy Section Identifier) List

UPSI List

Enter the UE Policy Section Identifier List (UPSI) information.

ANDSP Supported by the UE

Select to indicate that Access Network Discovery & Selection Policy (ANDSP) is supported by the UE.

Tcl Parameter: N15NpcfAndspEn

Number of UPSIs

Select the number of UPSIs (UE Policy Section Identifier). Up to 4.

Enter MCC (Mobile Country Code). Default = 111.

Enter MNC (Mobile Network Code). Default = 11.

Select the number of UPSCs (UE Policy Section Code). Up to 8.

Enter the UE Policy Section Code (UPSC). Range 0 to 65535, 0 is allowed.

Default : 1

Tcl Parameter: N15NpcfNumUpsiSubListCnt

Tcl Parameter: N15NpcfNumUpsiMcc_1

Tcl Parameter: N15NpcfNumUpsiMnc_1

Tcl Parameter: N15NpcfNumUpsiUpscCnt_1

Tcl Parameter: N15NpcfNumUpsiUpscValue_1

Presence Information

Number of Presence Information

Select the number of Presence Information.

Range: 1 to 4

Tcl Parameter: N15NpcfPreseNumber

Presence Info ID

Enter the Presence Info ID.

Range: 1 to 255 characters

Default: pres_info_1, pres_info_2, pres_info_3, pres_info_4

Tcl Parameter: N15NpcfPreseInfoId_1

Presence State

Select the Presence State.

Options: IN_AREA, OUT_OF_AREA, UNKNOWN, INACTIVE

Tcl Parameter: N15NpcfPreseState_1

Tracking Area List

Select to enter the Tracking Area Lists (up to 4)

Tcl Parameter: N15NpcfPreseIncTacListEn_1

Tcl Parameter: N15NpcfPreseIncTacListNum_1

MCC

MNC

Enter the Mobile Country Code (3 digits) and Mobile Network Code (between two and three digits).

Default: 000

Tcl Parameter: N15NpcfPreseTacListMcc_1_1

Tcl Parameter: N15NpcfPreseTacListMnc_1_1

TAC

Enter the Tracking Area Code (TAC). Enter 4 to 6 Hex digits.

Tcl Parameter: N15NpcfPreseTacListTac_1_1

NCGI List

Select to enter the NCGI (New Radio) Lists (up to 4).

Tcl Parameter: N15NpcfPreseIncNcgiListEn_1

Tcl Parameter: N15NpcfPreseIncNcgiListNum_1

MCC

MNC

Enter the Mobile Country Code (3 digits) and Mobile Network Code (between two and three digits).

Default: 000

Tcl Parameter: N15NpcfPreseNcgiListMcc_1_1

Tcl Parameter: N15NpcfPreseNcgiListMnc_1_1

NR Cell Id.

Enter the New Radio (NR) Cell ID. Enter 9 Hex digits.

Tcl Parameter: N15NpcfPreseNcgiListNrCellId_1_1

ECGI List

Select to enter the ECGI (EUTRAN) Lists (up to 4).

Tcl Parameter: N15NpcfPreseIncEcgiListEn_1

Tcl Parameter: N15NpcfPreseIncEcgiListNum_1

MCC

MNC

Enter the Mobile Country Code (3 digits) and Mobile Network Code (between two and three digits).

Default: 000

Tcl Parameter: N15NpcfPreseEcgiListMcc_1_1

Tcl Parameter: N15NpcfPreseEcgiListMnc_1_1

EUTRAN Cell Id.

Enter the EUTRAN Cell ID. Enter 7 Hex digits.

Tcl Parameter: N15NpcfPreseEcgiListEutraCellId_1_1

Global RAN Node ID List

Select to enter the Global RAN Node ID Lists (up to 4).

Tcl Parameter: N15NpcfPreseIncGRanNodeListEn_1

Tcl Parameter: N15NpcfPreseIncGRanNodeListNum_1

MCC MNC

Enter the Mobile Country Code (3 digits) and Mobile Network Code (between two and three digits).

Default: 000

Tcl Parameter: N15NpcfPreseGRanNodeListMcc_1_1

Tcl Parameter: N15NpcfPreseGRanNodeListMnc_1_1

N3IWF NG RAN Node

Enter the N3IWF (Non-3GPP Inter-Working Function Identifier) and the NG RAN Node (Non-3GPP RAN Node Id).

N3IWF and NG RAN Node are mutually exclusive.

Select the NG RAN Node Type : gNB, MacroNGeNB, LMacroNGeNB, SMacroNGeNB

Tcl Parameter: N15NpcfPreseGRanNodeListN3wifEn_1_1

Tcl Parameter: N15NpcfPreseGRanNodeListN3wif_1_1

Tcl Parameter: N15NpcfPreseGRanNodeListNgRanNodEn_1_1

Tcl Parameter: N15NpcfPreseGRanNodeListNgRanNod_1_1

Tcl Parameter: N15NpcfPreseGRanNodeListNgRanNodId_1_1

Service Area Restrictions

Select the number of Service Area Restrictions.

Range: 0 to 16

Tcl Parameter: N15NpcfServiceAreaResAreaNum

Restriction Type	Select the Restriction Type. Options: Allowed, Not Allowed, Forbidden Default: Allowed Tcl Parameter: N15NpcfServiceRestrictionType
Only Number of Service Areas	Select Only Number of Service Areas. Available is Restriction Type = Allowed. The Number of TACs and Number of Areas Codes become disabled is enabled. Tcl Parameter: N15NpcfServiceAreaResOnlyNumberInfo
Number of TACs	Enter the Number of Tracking Area Codes (TACs). Enter up to 16 Tracking Area Codes (TAC). Enter up 6 Hex digits. Range: 0 to 16 Tcl Parameter: N15NpcfServiceAreaResTacsNum_1 Tcl Parameter: N15NpcfServiceAreaResTac_1
Number of Area Codes	Enter the Number of Area Codes. Enter up to 16 Area Codes. Enter up 6 Hex digits. Range: 0 to 16 Tcl Parameter: N15NpcfServiceAreaResAreaCodeNum_1 Tcl Parameter: N15NpcfServiceAreaResAreaCode_1

New Service Area Restrictions

Select the number of New Service Area Restrictions.

Range: 0 to 16

Tcl Parameter: N15NpcfNewServiceAreaResAreaNum

Restriction Type	Select the Restriction Type. Options: Allowed, Not Allowed, Forbidden Default: Allowed Tcl Parameter: N15NpcfNewServiceRestrictionType
Only Number of Service Areas	Select Only Number of Service Areas. Available is Restriction Type = Allowed. The Number of TACs and Number of Areas Codes become disabled is enabled. Tcl Parameter: N15NpcfNewServiceAreaResOnlyNumberInfo
Number of TACs	Enter the Number of Tracking Area Codes (TACs). Enter up to 16 Tracking Area Codes (TAC). Enter up 6 Hex digits. Range: 0 to 16 Tcl Parameter: N15NpcfNewServiceAreaResTacsNum_1 Tcl Parameter: N15NpcfNewServiceAreaResTac_1
Number of Area Codes	Enter the Number of Area Codes. Enter up to 16 Area Codes. Enter up 6 Hex digits. Range: 0 to 16 Tcl Parameter: N15NpcfNewServiceAreaResAreaCodeNum_1 Tcl Parameter: N15NpcfNewServiceAreaResAreaCode_1

UE Policy Delivery Result 1 and 2

Enter the Number of Rejected UPSCs (UE Policy Section Code) for Result 1 and Result 2 (New). Select up to 4 UPSIs.

Tcl Parameter: N15NpcfRejUpscsNum

Tcl Parameter: N15NpcfNewRejUpscsNum

UPSIs (1 to 4)

Enter MCC (Mobile Country Code). Default = 111.

Enter MNC (Mobile Network Code). Default = 11.

Enter the UE Policy Section Code (UPSC). Range 0 to 65535, Default : 0

Tcl Parameter: N15NpcfRejMcc_1

Tcl Parameter: N15NpcfRejMnc_1

Tcl Parameter: N15NpcfRejUpscValue_1

Tcl Parameter: N15NpcfNewRejMcc_1

Tcl Parameter: N15NpcfNewRejMnc_1

Tcl Parameter: N15NpcfNewRejUpscValue_1

User Location Change

Enter the New User Location.

Time Zone

Enter the new Time Zone.

Unrestricted text field.

Tcl Parameter: N15NpcfNewTimeZone

RAT Type

Select the new RAT (Radio Access Technology) Type.

NR = New Radio, EUTRA = Evolved Universal Terrestrial Radio Access

Options: NR (default), EUTRA, WLAN, Virtual

Tcl Parameter: N15NpcfNewRatType

Access Type

Select the Access Type.

Options : NON_3GPP_ACCESS (default), 3GPP_ACCESS

Tcl Parameter: N15NpcfNewAccessInfoAccessType

MCC

MNC

Enter the new Mobile Country Code (3 digits) and the new Mobile Network Code (between two and three digits).

Default: 000

Tcl Parameter: N15NpcfNewMcc

Tcl Parameter: N15NpcfNewMnc

TAC

Enter the new Tracking Area Code (TAC). Enter 4 to 6 Hex digits.

Tcl Parameter: N15NpcfNewTac

NR Cell Id

Available if RAT Type = NR (New Radio). Enter the new NR Cell Id. Enter up to 9 Hex digits.

Tcl Parameter: N15NpcfNewNrCellId

EUTRA Cell Id

Available if RAT Type = EUTRA. Enter the new EUTRA Cell Id. Enter up to 7 Hex digits.

Tcl Parameter: N15NpcfNewEutraCellId

N3ga Iwfld UE IPv4 Address

UE IPv6 Address

Port Number

Available if RAT Type = WLAN or VIRTUAL.

Enter the new N3ga IwfId. (Non-3GPP Inter-Working Function Identifier). Unrestricted Text string.

Select to enter the new UE IPv4 Address - Enter a valid IPv4 Address for the UE.

Select to enter the new UE IPv6 Address - Enter a valid IPv6 Address for the UE.

Select to enter the new Port Number - Enter a port number. Range: 0 to 65535, Default: 1000

Tcl Parameter: N15NpcfNewN3iwfId

Tcl Parameter: N15NpcfNewN3UeIpv4AddrEn

Tcl Parameter: N15NpcfNewN3UeIpv4Addr

Tcl Parameter: N15NpcfNewN3UeIpv6AddrEn

Tcl Parameter: N15NpcfNewN3UeIpv6Addr

Tcl Parameter: N15NpcfNewN3PortNumberEn

Tcl Parameter: N15NpcfNewN3PortNumber

Original Settings / Update Settings

Available when Npcf Version (29.507) >= 16.7.0/Mar2021.

Access Type

Select to enter the Number of Access Types for Original Settings and Update Settings.

Range : 1 to 4

Default : 1

Options: 3GPP_ACCESS (default), NON_3GPP_ACCESS

Tcl Parameter: N15NpcfOrgAcTypesEn

Tcl Parameter: N15NpcfUpdAcTypesEn

Tcl Parameter: N15NpcfOrgAcTypesNum

Tcl Parameter: N15NpcfUpdAcTypesNum

Tcl Parameter: N15NpcfOrgAcType_1

Tcl Parameter: N15NpcfUpdAcType_1

RAT Type

Select to enter the RAT (Radio Access Technology) Type for Original Settings and Update Settings.

NR = New Radio, EUTRA = Evolved Universal Terrestrial Radio Access

Options: NR (default), EUTRA, WLAN, Virtual

Tcl Parameter: N15NpcfOrgRatTypesEn

Tcl Parameter: N15NpcfUpdRatTypesEn

Tcl Parameter: N15NpcfOrgRatTypesNum

Tcl Parameter: N15NpcfUpdRatTypesNum

Tcl Parameter: N15NpcfOrgRatType_1

Tcl Parameter: N15NpcfUpdRatType_1

Allowed S-NSSAI

Select Allowed S-NSSAI and enter the Number of Allowed S-NSSAIs.

S-NSSAI (Single - Network Slice Selection Information).

The S-NSSAI contains two components: the SST (Slice / Service Type) and an optional SD (Slice Differentiator).

Tcl Parameter: N15NpcfOrgAlwSnssaiEn

Tcl Parameter: N15NpcfUpdAlwSnssaiEn

Tcl Parameter: N15NpcfOrgAlwSnssaiNum

Tcl Parameter: N15NpcfUpdAlwSnssaiNum

SST /SD

The S-NSSAI contains two components: the SST (Slice / Service Type) and an optional SD (Slice Differentiator).

Range of SST : 0 to 255, default : 0

Range of SD : 1 to 6 Hex Characters , Default : 0

Tcl Parameter: N15NpcfOrgAlwSst_1

Tcl Parameter: N15NpcfUpdAlwSst_1

Tcl Parameter: N15NpcfOrgAlwSdEn_1

Tcl Parameter: N15NpcfUpdAlwSdEn_1

Tcl Parameter: N15NpcfOrgAlwSd_1

Tcl Parameter: N15NpcfUpdAlwSd_1

S-NSSAI HPLMN

SST /SD

Select to enable the S-NSSAI for the HPLMN (The Home Public Land Mobile Network identifies the PLMN (Public Land Mobile Network))

The S-NSSAI contains two components: the SST (Slice / Service Type) and an optional SD (Slice Differentiator).

Range of SST : 0 to 255, default : 0

Range of SD : 1 to 6 Hex Characters , Default : 0

Tcl Parameter: N15NpcfOrgAlwHplmnEn_1

Tcl Parameter: N15NpcfUpdAlwHplmnEn_1

Tcl Parameter: N15NpcfOrgAlwHplmnSst_1

Tcl Parameter: N15NpcfUpdAlwHplmnSst_1

Tcl Parameter: N15NpcfOrgAlwHplmnSdEn_1

Tcl Parameter: N15NpcfUpdAlwHplmnSdEn_1

Tcl Parameter: N15NpcfOrgAlwHplmnSd_1

Tcl Parameter: N15NpcfUpdAlwHplmnSd_1

Non-3GPP Allowed S-NSSAI

Select Non-3GPP Allowed S-NSSAI and enter the Number of Non-3GPP Allowed S-NSSAIs.

S-NSSAI (Single - Network Slice Selection Information).

The S-NSSAI contains two components: the SST (Slice / Service Type) and an optional SD (Slice Differentiator).

Tcl Parameter: N15NpcfOrgN3gAlwSnssaiEn

Tcl Parameter: N15NpcfUpdN3gAlwSnssaiEn

Tcl Parameter: N15NpcfOrgN3gAlwSnssaiNum

Tcl Parameter: N15NpcfUpdN3gAlwSnssaiNum

SST /SD

The S-NSSAI contains two components: the SST (Slice / Service Type) and an optional SD (Slice Differentiator).

Range of SST : 0 to 255, default : 0

Range of SD : 1 to 6 Hex Characters , Default : 0

Tcl Parameter: N15NpcfOrgN3gAlwSst_1

Tcl Parameter: N15NpcfUpdN4gAlwSst_1

Tcl Parameter: N15NpcfOrgN4gAlwSdEn_1

Tcl Parameter: N15NpcfUpdN3gAlwSdEn_1

Tcl Parameter: N15NpcfOrgN4gAlwSd_1

Tcl Parameter: N15NpcfUpdN3gAlwSd_1

S-NSSAI HPLMN

SST /SD

Select to enable the S-NSSAI for the HPLMN (The Home Public Land Mobile Network identifies the PLMN (Public Land Mobile Network))

The S-NSSAI contains two components: the SST (Slice / Service Type) and an optional SD (Slice Differentiator).

Range of SST : 0 to 255, default : 0

Range of SD : 1 to 6 Hex Characters , Default : 0

Tcl Parameter: N15NpcfOrgN3gAlwHplmnEn_1

Tcl Parameter: N15NpcfUpdN3gAlwHplmnEn_1

Tcl Parameter: N15NpcfOrgN3gAlwHplmnSst_1

Tcl Parameter: N15NpcfUpdN3gAlwHplmnSst_1

Tcl Parameter: N15NpcfOrgN3gAlwHplmnSdEn_1

Tcl Parameter: N15NpcfUpdN3gAlwHplmnSdEn_1

Tcl Parameter: N15NpcfOrgN3gAlwHplmnSd_1

Tcl Parameter: N15NpcfUpdN3gAlwHplmnSd_1

SMF Selection Data

Select to enter the SMF Selection Data.

Available for Update Settings only.

Tcl Parameter: N15NpcfUpdSmfSelDataEn

Unsupported DNN

Select to indicate an unsupported DNN for the SMF Selection data.

Tcl Parameter: N15NpcfUpdSmfSelUnsuppDnnEn

DNN

Select to enter the DNN for the SMF Selection data.

Tcl Parameter: N15NpcfUpdSmfSelDnnEn

Tcl Parameter: N15NpcfUpdSmfSelDnn

S-NSSAI

SST /SD

Select to enable the S-NSSAI for the SMF Selection data.

The S-NSSAI contains two components: the SST (Slice / Service Type) and an optional SD (Slice Differentiator).

Range of SST : 0 to 255, default : 0

Range of SD : 1 to 6 Hex Characters , Default : 0

Tcl Parameter: N15NpcfUpdSmfSelSnssaiEn

Tcl Parameter: N15NpcfUpdSmfSelSst

Tcl Parameter: N15NpcfUpdSmfSelSdEn

Tcl Parameter: N15NpcfUpdSmfSelSd

Candidate for Replacement

Select to enter the Candidate for Replacement details the SMF Selection Data.

Enter the Number of Candidates.

Range : 1 to 4

Default : 1

Available for Update Settings only.

Tcl Parameter: N15NpcfUpdSmfSelCandEn

Tcl Parameter: N15NpcfUpdSmfSelCandNum

Candidate S-NSSAI

SST /SD

Select to enable the Candidate S-NSSAI for the SMF Selection data.

The S-NSSAI contains two components: the SST (Slice / Service Type) and an optional SD (Slice Differentiator).

Range of SST : 0 to 255, default : 0

Range of SD : 1 to 6 Hex Characters , Default : 0

Tcl Parameter: N15NpcfUpdSmfSelCandSst_1

Tcl Parameter: N15NpcfUpdSmfSelCandSdEn_1

Tcl Parameter: N15NpcfUpdSmfSelCandSd_1

Candidate DNN

Select to enter the Candidate DNNs for the SMF Selection data.

Enter the Number of Candidate DNNs.

Range : 1 to 4

Default : 1

Tcl Parameter: N15NpcfUpdSmfSelCandDnnsEn_1

Tcl Parameter: N15NpcfUpdSmfSelCandDnnsNum_1

Tcl Parameter: N15NpcfUpdSmfSelCandDnns_1_1

Redirection Settings

Select Redirection Settings to enter the Location and Target NF Instance ID.

Available when Npcf Version (29.507) >= 16.7.0/Mar2021.

Enter a valid IPv4 address for Location. Default : 1.1.1.1

Select to enter a Target NF Instance ID.

Format : UUID version 4: 4hexOctet-2hexOctet-2hexOctet-2hexOctet-6hexOctet

Tcl Parameter: N15NpcfRedirectSettingEn

Tcl Parameter: N15NpcfRedirectLoc

Tcl Parameter: N15NpcfRedirectInstIdEn

Tcl Parameter: N15NpcfRedirectInstId

^ Back to Top