The AAA App tab is used to define the method to identify the diameter application supported by the node, the type of messages that will be generated by the AAA Server node, and the information included in the messages.
Wm/Wg Include MS ISDN Include MS IMSI
|
|
Diameter Server Accounting, Diameter Server Authentication, AAA Server Node, IP Instance and Test Summary report tabs.
Provisions the Application, Auth-Application and Acct-Application AVPs in messages sent by a node and identifies the Diameter application supported by the node. The Application selection determines which Authentication algorithms display for your selection. Parameter Class: Basic: Custom Multiple Choice Values: Tcl Parameter:
You may select the Wm interface to allow EAP authentication, you can also configure any Auth-request-type as part of the same session (for example, you can configure the NASREQ/NASResponse Auth-request-type via AVP Configuration).
Related Measurements |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
WiMAX HA4 Command Code checkbox is only available when the Wimax Mip4 option is selected from the Application dropdown list. Select the checkbox and enter the Command Code of the message type not defined by IANA official codes. Tcl Parameter: DiaCmdCodeWha4En |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Select the accounting session mode for a Diameter test. Options: Stateful or Stateless Default: Stateful Tcl Parameter: DiaSrvStateMachine Available when State Mode is Stateful. Define the accounting session timer. Each session is individually timed, and the timer begins when an ACA is sent in response to an ACR start message. The timer is reset whenever an interim record is received for that session. The timer value should be set to at least twice the expected interim update cycle to avoid unnecessary session termination due to transmission delays. Enter 0 to disable the timer. Range: 0 — 65535 Default: 0 Tcl Parameter:
Related Measurements |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Configure the number of APNs per subscriber when Application is S6b, S6b/STa/SWx, S6b/SWm/SWx ,S6b/SWa/SWx (multiple APN is support for back-to-back testing). Default: 1 Range: 1 - 11 Tcl Parameter: DiaSrvNumApns |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Available when Application is Swa, SWm, S6b/STa/SWx, S6b/SWm/SWx ,S6b/SWa/SWx, Wa, Wa/Wx or Wa/Wm/Wg/Wx. Select to either re-authenticate or re-authorize and enter the interval is in seconds. Default: 20 seconds Range: 0 - 65535 If the re-auth-type in the RAR is AUTHORIZE_ONLY, LS STa client session sends an AAR message to AAA requesting re-authorization. Then AAA retrieves the subscription profile again (sends/receives SAR/SAA messages over SWx interface ). If the re-auth-type in the RAR is AUTHORIZE_AUTHENTICATE, LS STa client session performs the authentication procedure. Re-Auth Interval: Enter the Re-Auth Interval in seconds. Enter value to simulate delay at the PGW to start S6b re-authorization/re-authentication procedure. When re-authorization or re-authentication timer expires, AAA Node sends RAR message with appropriate re-auth-type over STa interface.
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Select the RAT (Radio Access Technology) to indicate the access network type. Options: WLAN, VIRTUAL, CDMA2000_1X, HRPD, UMB and EHRPD. Default: EHRPD Tcl Parameter: DiaSrvRatType |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
When you set Application as NASREQ or WiMAX MIPv4, authentication can be performed with a password (the Password selection is available). See User Credentials |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Use to configure EAP authentication support for a virtual server. You can configure the methods that will be supported and the acceptable credentials for each method with the EAP Settings window. The EAP Authentication Settings button and the associated parameters are available only when the Application value is WiMAX MIPv4 and Include State AVPThe Include State AVP parameter checkboxes, the Multiround DEA Message and Success DEA Message, are available only during AAA Diameter testing. These become available when EAP Settings is enabled. Enabling these checkboxes allows the value of the State AVP to be generated in hardcode. This reduces the number of authentication round trips.
Value: 0/1 Default: 1=enabled Tcl Parameter: DiaSrvIncStateAvpInMultiroundDEA
Value: 0/1 Default: 1=enabled Tcl Parameter: DiaSrvIncStateAvpInSuccessDEA Related Measurements |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Select to enable . This AVP shall indicate the domain name to replace the APN-OI in the non-roaming case or in the home roaming case when constructing the PDN GW FQDN upon performing a DNS resolution. Tcl Parameter: DiaSrvApnOIRep |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Present if NBM is used. It contains an AAA/HSS assigned identity. Tcl Parameter: DiaSrvMobileNodeIdEn |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Use the checkbox to enable multiple rounds of EAP authentication support for a virtual server as specified in RFC 4739. You can configure the methods that will be supported and the acceptable credentials for each method with the EAP Settings window. Tcl Parameter: MultEapEn
User NameSee User Credentials Tcl Parameter: DiaMUsername |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Select from the Drop Down options to choose WLAN Authorization Mode via WLAN Direct Access or WLAN 3GPP IP Access. Tcl Parameter: DiaSrvAuthMode |
These configurations are available for Wm Interface and Wm/Wg Interfaces.
Wg Interface: Reference point between a 3GPP AAA Server/Proxy and WAG (Wireless LAN Access Gateway).
Wm/Wg Interfaces: Reference point between a Packet Data Gateway and a 3GPP AAA Server or 3GPP AAA proxy.
In AAA Node test case, you may select one or more identifies and enter the appropriate values, which are incremented for each Mobile Subscriber.
|
||||||||||
Enable Routing Policies | Enabled by default when you select Wm/Wg Interface and option when you select Wm Interface. Indicates that any existing policy is overridden by the Policy downloaded by the WAG (Wireless Access Gateway). Tcl Parameter: DiaSrvRoutingPoliciesEn | |||||||||
Include Routing Policies in DEA Messages | Select to include Routing Policies in DEA (Diameter-EAP-Answer) messages. Tcl Parameter: DiaSrvPoliciesInDeaEn | |||||||||
Starting User IP Address | Enter the Starting IP Address to use the Policy. | |||||||||
Number of Policies |
Click
|
|||||||||
Each Policy defines the IP address of the traffic permitted in or out, whether the policy is included in DEA Message and/or included in the initially downloaded policy.
|
||||||||||
Behavior Upon Receiving WAG Initiated Routing Policy Cancellation |
WAG Initiated Routing Policy Cancellation is invoked by the WAG if the session specific routing policy has been removed from the WAG and this removal has not been preceded by Routing policy Cancellation Procedure sent from the 3GPP AAA Server to the WAG. Select the action to perform when a cancellation of routing policy is initiated by WAG:
The 3GPP AAA Server sets the Result-Code to DIAMETER_SUCCESS and sends the ASA command to the WAG. |
|||||||||
Policies Included in Restarts | Available when you select
|