Main Tab Fields

cfguser password

Displays the cfguser password.

N/A

N/A

TAS IP

Displays the IP address of the test server's TAS.

N/A

N/A

NTP Sync Status fields

^ Back to Top

Time Sync

NTP IP

A new tab Time Sync is available to configure NTP or PTP (as of Release 16.2).  Defines the IP address of the NTP server

N/A

N/A

Interface

Displays the name of the management port physical interface.

N/A

N/A

IP

Displays the IPv4 address of the management port physical interface.

N/A

N/A

Hostname

Displays the test server's host name.

N/A

N/A

Gateway

Displays the address of the management port's default IPv4 gateway.

N/A

N/A

IPv6 Gateway

Defines the address of the IPv6 gateway in the test network.

0::0

N/A

IPv6 Gateway Mask

Defines the mask for the IPv6 gateway in the test network.

/0

N/A

Mask

Displays the IPv4 subnet mask of the management port physical interface.

N/A

N/A

Pool IP

Defines the starting IPv4 address for the address pool associated with the management port.

This field is optional. If you do not want an address pool assigned to the management port, leave the field blank. If an IP address is entered, the # IPs must also be defined.

0.0.0.0

N/A

# IPs

Defines the number of IP addresses available in the address pool associated with the management port.

This field is optional. If you do not want an address pool assigned to the management port, leave the field blank. If a number is entered, Pool IP must also be defined.

1 — 1000

N/A

Auto Negotiate

A checkbox that defines whether the speed and duplex settings are set through negotiation with the endpoint (Checked), or manually defined (Unchecked).

When the box is not checked, the Speed and Duplex fields are enabled.

N/A

N/A

Speed

Defines the transmission speed for the management port.

This field is disabled if Auto Negotiate is checked.

10, 100, 1000

N/A

Duplex

Defines the transmission duplex for the management port.

This field is disabled if Auto Negotiate is checked.

Full, Half

N/A

Alternate IPv4 Address, Alternate IPv4 Mask, Alternate IPv4Gateway

If an IPv6 Management Port address is used, additional fields will be displayed: Alternate IPv4 Address, Alternate IPv4 Mask, Alternate IPv4Gateway are displayed.

N/A

N/A

Local Interface fields

^ Back to Top

Pool IP

Defines the starting address of the IPv4 address pool associated with the local test port.

This field is optional. If you do not want an address pool assigned to the test port, leave the field blank. If an IP address is entered, the # of IPs must also be defined.

0.0.0.0

N/A

# of IPs

Defines the number of addresses available in the IPv4 address pool associated with the local test port.

This field is optional. If you do not want an address pool assigned to the test port, leave the field blank. If a number is entered, Pool IP must also be defined.

N/A

N/A

Pool IPv6

Defines the starting address of the IPv6 address pool associated with the local test port.

This field is optional. If you do not want an address pool assigned to the test port, leave the field blank. If an IP address is entered, the # of IPs V6 must also be defined.

0::0

N/A

# of IPs V6

Defines the number of addresses available in the IPv6 address pool associated with the local test port.

This field is optional. If you do not want an address pool assigned to the test port, leave the field blank. If a number is entered, Pool IPv6 must also be defined.

N/A

N/A

Data Gen Performance

Data Gen Performance to indicate the threading mode used to run the test server. Additional details in topic About Test Server Configuration

Legacy, Max and Fireball.

Legacy

Reserve Resources for:

Select to allocate CPU core to perform POLQA and/or PEVQ Calculation or Digital Signal Processing (Ringtone detection). For addition information go to About VoLTE POLQA Testing and About VoLTE VMAF Testing .For additional information on Ringtone Detection go to RTP.

POLQA/VMAF or Digital Signal Processing

POLQA/VMAF

UE Info Level

Default = 1. Select level 10 to get all the VisionWorks Results that are used by the Landslide Test Analytics Reporting.  Select Level = 3 to see only the UE IP Address and main State transitions. Remaining values are for future use. Additional configuration details can be found in the topic VisionWorks Solution.

1 to 10

10

Enable Remote Test/Auto TS Mode

Note : This option is no longer supported.

Enable for Remote test, Auto TS Mode. Select for a single test server test session to be scheduled to run many times remotely on a test server, without the TAS sequencing the test sessions themselves. If the TAS and Test Server lose connectivity between each other, the tests will continue to run on schedule. When the connectivity is re-established, the TAS will catch up and retrieve the test results for any tests that completed while disconnected.  The number of TS Processes must be 1. You must enable this option in the "Test Session" - Select "Remote Test, Auto TS Mode". Additional details can be found in the About the Test Session Window.

N/A

N/A

Interface

Displays the name of the test port physical interface. IPv4 and IPv6 configurations for one interface are displayed on separate rows, and "v6" is appended to the interface name for IPv6 configurations.

N/A

N/A

IP

Defines the IPv4 or IPv6 address of the test port physical interface.

0.0.0.0 (IPv4)

0::0 (IPv6)

N/A

Mask

Defines the subnet mask of the test port physical interface.

0.0.0.0 (IPv4)

/0 (IPv4 or IPv6)

N/A

Pool IP

Defines the starting IP address of the address pool associated with the test port.

This field is optional. If you do not want an address pool assigned to the test port, leave the field blank. If an IP address is entered, the # of IPs must also be defined.

0.0.0.0 (IPv4)

0::0 (IPv6)

N/A

# of IPs

Defines the number of IP addresses available in the address pool associated with the test port.

This field is optional. If you do not want an address pool assigned to the test port, leave the field blank. If a number is entered, Pool IP must also be defined.

1 — 1000

N/A

DHCP

Select for request to DHCP server for test ports - Additional details in topic Managing Test Server Other Ethernet Tab.

DHCP feature is not supported on Aonic cards.

N/A

N/A

Auto

A checkbox that defines whether the speed and duplex settings are set through negotiation with the endpoint (Checked), or manually defined (Unchecked).

When the box is not checked, the Speed and Duplex fields are enabled.

N/A

N/A

Enabled On Boot

A checkbox that defines whether the test port is enabled when the test server is rebooted.

N/A

N/A

Auto

A checkbox that defines whether the speed and duplex settings are set through negotiation with the endpoint (Checked), or manually defined (Unchecked).

When the box is not checked, the Speed and Duplex fields are enabled.

N/A

N/A

Limit ETH MTU to 2K bytes -

When enabled, it provides additional memory for application usage. Additional details in topic Managing Test Server Other Ethernet Tab.

 N/A

N/A

Hybrid mode

Additional details in topic Managing Test Server Other Ethernet Tab.

N/A

N/A

Hybrid Type

Additional details in topic Managing Test Server Other Ethernet Tab.

N/A

N/A

Promiscuous

Provides the ability to turn off Promiscuous Mode for Virtual Test Servers.

N/A

N/A

VLANs and VLAN ID Ranges

Provides the ability to configure VLAN ID Ranges on Virtual Test Servers for specific NIC Types only.

N/A

N/A

Disable V6 Route Advert

Provides the ability to disable V6 Router Advertisement for an incoming V6 Router Solicitation..

N/A

N/A