The values on the RTP Voice tab.
The MN (client) side of the test is reported in the L3 Client, L4 Client, and L5-7 Client tabs and The Network (server) side is reported in the L3 Server, L4 Server and L5-7 Server tabs (measurements from the Network Host emulator used in the test). These measurements are available when Data Traffic is included in the test.
|
NOTES:
|
In the default view, the Reports tab displays the Summary view, which summarizes the measurements for the test session. If your test includes multiple test cases, you can view the report for a single test case by changing the report view...
Unless otherwise noted, cumulative values report the number of occurrences or rates calculated since the start of the test, and per-interval values report the number of occurrences or rates calculated during the interval. You can view either by changing the measurement values...
RTP Packets Sent — The number of RTP packets sent.
RTP Packets Sent/Sec (P-I) — The number of RTP packets sent per second.
RTP Sent Packets Discarded — The number of RTP sent packets that were discarded.
RTP Packets Received — The number of RTP packets received.
RTP Packets Received/Sec (P-I) — The number of RTP packets received per second.
RTP Packets Received Out of Order — The number of RTP received packets that were received out of order.
RTP Bytes Sent — The number of RTP bytes sent.
RTP Bits Sent/Sec — The number of RTP bits sent per second.
RTP Bytes Received — The number of RTP bytes received.
RTP Bits Received/Sec — The number of RTP bits received per second.
RTP Packets Late Arrival — The RTP packets delayed more than the time entered in Jitter Buffer Size (RTP Voice) and less than the Max Network Delay (RTP Voice) are considered as late arrival.
RTP Packets Lost — If a packet does not arrive before the specified delay time set on Max Network Delay (RTP Voice), it's considered as lost (RTP Packets Lost). All the packets arrived after Max Network Delay are discarded. The number of packets lost.
RTP Packets Expected — The total number of Expected RTP Packets.
RTP Packet Loss % — If a packet does not arrive before the specified delay time set on Max Network Delay (RTP Voice), it's considered as lost (RTP Packets Lost). Percentage of lost packets. The Packet Loss Percentage is calculated by ((Packets Lost / Packets Expected) * 100). Note: For interval 2 calculation == ((Packets Lost[2] - Packets Lost[1] / Packets Expected [2] - Packets Expected [1] ) * 100).
RTP Packet Loss Time — If a packet does not arrive before the specified delay time set on Max Network Delay (RTP Voice), it's considered as lost (RTP Packets Lost). All the packets arrived after Max Network Delay are discarded.
RTP Average Jitter (P-I) — Average jitter for RTP Packets. Notes: To get better test results for Jitter measurements (Average Jitter, Minimum Jitter, Maximum Jitter), please set as follows: 1. Set default value(15s) as "Interval Period" the Report Option (if set at 5s, you cannot get best jitter results). 2. Enable “Reserve resource for POLQA/PEVQ/IVR” 3. Use the latest Ubuntu version.
RTP Minimum Jitter — Minimum jitter for RTP Packets. See notes in Average Jitter.
RTP Maximum Jitter — Maximum jitter for RTP Packets. See notes in Average Jitter.
RTP Average Latency (P-I) — Latency is the delta time between sending RTP packet to receiving RTP packet. Average = Total of sampling points divided by the number of samples.
RTP Minimum Latency — Latency is the delta time between sending RTP packet to receiving RTP packet. The Minimum latency time of all the sampling points.
RTP Maximum Latency — Latency is the delta time between sending RTP packet to receiving RTP packet. The Maximum latency time of all the sampling points.
RTP Median Latency — Latency is the delta time between sending RTP packet to receiving RTP packet. The Median latency time of all the sampling points.
RTP Standard Deviation Latency — Latency is the delta time between sending RTP packet to receiving RTP packet. The Standard Deviation latency time of all the sampling points.
RTP 90th Percentile Latency — Latency is the delta time between sending RTP packet to receiving RTP packet. The 90th percentile latency time of all the sampling points.
RTP 98th Percentile Latency — Latency is the delta time between sending RTP packet to receiving RTP packet. The 98th percentile latency time of all the sampling points.
RTP 99 Confidence Latency — Latency is the delta time between sending RTP packet to receiving RTP packet. The 99 confidence latency time of all the sampling points.
RTCP Packets Sent — Total number of RTCP packets sent.
RTCP Packets Received — Total number of RTCP packets received.
RTCP Bytes Sent — Total number of bytes sent in RTCP packets (Payload only) sent.
RTCP Bytes Received — Total number bytes sent in RTCP packets (Payload only) received.
RTCP SR Packets Sent — Total number of RTCP SR (Send Report) packets sent.
RTCP SR Packets Received — Total number of RTCP SR (Send Report) packets received.
RTCP RR Packets Sent — Total number of RTCP RR (Receive Report) packets sent.
RTCP RR Packets Received — Total number of RTCP RR (Receive Report) packets received.
RTCP XR Packets Sent — Total number of RTCP XR (eXtended Report) packets sent.
RTCP XR Packets Received — Total number of RTCP XR (eXtended Report) packets received.
RTCP Received Packets Discarded — The number of RTCP received packets that were discarded because of: Wrong format, RTCP Message Content is not supported or RTCP is not active for a given RTP Session.
RTCP RTP Packets Sent — Total number of RTCP packets sent by peer.
RTCP RTP Bytes Sent — Total number of bytes of RTP data (Payload only) sent.
RTCP Received RTP Packets Lost — Total number of lost RTP packets. It counts: Lost packets and Packets arrived too late (after DMF's Network Time Delay)
RTCP Average RTD (P-I) — Average RTD (Round Trip Delay) for RTCP Packets.
RTCP Minimum RTD — Minimum RTD (Round Trip Delay) for RTCP Packets.
RTCP Maximum RTD — Maximum RTD (Round Trip Delay) for RTCP Packets.
RTCP RTP Average Jitter (P-I) — Average RTP Interrival jitter reported by peer.
RTCP RTP Minimum Jitter — Minimum RTP Interrival jitter reported by peer.
RTCP RTP Maximum Jitter — Maximum RTP Interrival jitter reported by peer.
RTP MOS-LQOn Meas Count — The number of times calculation of MOS-LQOn (Narrowband) was attempted. Used in POLQA Testing - Additional information in About VoLTE POLQA Testing.
RTP MOS-LQOn Successes — The number of times calculation of MOS-LQOn (Narrowband) was successful. Used in POLQA Testing - Additional information in About VoLTE POLQA Testing.
RTP MOS-LQOn Failures — The number of times calculation of MOS-LQOn (Narrowband) failed. Standard Caution Highlighting v > 0. Used in POLQA Testing - Additional information in About VoLTE POLQA Testing.
RTP MOS-LQOn Average — Used in POLQA Testing - Additional information in About VoLTE POLQA Testing.
RTP MOS-LQOn Minimum — Used in POLQA Testing - Additional information in About VoLTE POLQA Testing.
RTP MOS-LQOn Maximum — Used in POLQA Testing - Additional information in About VoLTE POLQA Testing.
RTP MOS-LQOsw Meas Count — The number of times calculation of MOS-LQOsw (Superwideband) was attempted. - Used in POLQA Testing - Additional information in About VoLTE POLQA Testing.
RTP MOS-LQOsw Successes — The number of times calculation of MOS-LQOsw (Superwideband) was successful. Used in POLQA Testing - Additional information in About VoLTE POLQA Testing.
RTP MOS-LQOsw Failures — The number of times calculation of MOS-LQOsw (Superwideband) failed. Standard Caution Highlighting v > 0. Used in POLQA Testing - Additional information in About VoLTE POLQA Testing.
RTP MOS-LQOsw Average — Used in POLQA Testing - Additional information in About VoLTE POLQA Testing.
RTP MOS-LQOsw Minimum — Used in POLQA Testing - Additional information in About VoLTE POLQA Testing.
RTP MOS-LQOsw Maximum — Used in POLQA Testing - Additional information in About VoLTE POLQA Testing.
RTP POLQA ECs Consumed — Used in POLQA Testing - Additional information in About VoLTE POLQA Testing.
The basic data measurements are available on L5-7 Client|Basic tab when any of the basic data types (PING, RAW, UDP, and TCP) are used in a Continuous Data test.
The advance data measurements are available on the L5-7 Client|Advanced tab when any of the Advanced Data protocols are used in a Continuous Data test.