PCC (Gx)


The PCC tab on Gx protocol tab contains the parameters that define the Gx interfaces to the PCRF. The PCC ab on the PCC-R3-P protocol tab contains the parameters that define PCC-R3-P interface to the PDF.

NOTES:

  • Although defined slightly different in their associated standards, both the 3GPP and 3GPP2 organizations have implemented a policy decision function and associated reference points. 3GPP2 defines the reference points as Tx and Ty, while 3GPP defines them as Rx and Gx.

  • In WIMAX Forum testing, PCC-T3-P is an extention of Ty/Gx referernce points.

Parameter Index

 

 

 

 

 

APN Assignments

 

Bearers

 

 

 

 

Default Bearers (D0)

 

Filter 1

Filter 2

 

 

 

Simulated Usages

 

Dedicated Bearers per Default (D0-B0)

Filter 1

Filter 2

 

Simulated Usages

 

 

 

 


 

 

 

Enable RAT Type

Select RAT (Radio Access Technology) Type to indicate the access network type.  For different access types, PCRF uses different diameter AVPs for some controls (i.e., different AVPs for sending packet filters in UTRAN vs. E-UTRAN) of outgoing messages. By default, RAT type is UTRAN.

Tcl Parameter: TyCcClnRatType

Enable APN Assignments

Select to enable APN Assignments pane.

Tcl Parameter: TyCcClnApnAssignmentsEn

Enable Sponsored Data Connectivity

This feature indicates support for sponsored data connectivity feature. If the PCEF supports this feature, the PCRF may authorize sponsored data connectivity to the subscriber.

Tcl parameter: TyCcClnSponsoredDataConnEn

Enable constant CCR-U transactions

Select to enable event based initiation of constant CCR-U messages. Additional fields below will be enabled when selected.

Bearer selection will be disabled.

Tcl parameter: TyCcClnConstCcruTranscEn

Transaction Start Delay (ms)

 

Delay time after all sessions have been established for triggering constant CCR-U messages.

Range: 0 — 65535

Default: 0

Tcl Parameter: TyCcClnTranscStartDelay

Transaction Rate (trans/s)

Transaction Rate for CCR-U messages. Ex. If Transaction rate is 1000, CCR-U messages will be transmitted continuously at a rate of 1000 sessions/sec until the Test Session stops.

Range: 0 — Variable (depends on test system's licensed capacity)

Default: 000

Tcl Parameter: TyCcClnCcruTranscRate

Select Event Trigger

(33) Usage-Report

Check box for sending Usage Report event trigger

Tcl Parameter: TyCcClnEventTriggerEn

CC-Total-Octets value

Enter the Total Octets value used in the Usage-Monitoring-Information AVP.

Range: 0 — 4294967295

Default: 0

Tcl Parameter: TyCcClnCcTotalOctetsVal

 

Enable Rule Operation Failure

Select to support Charging-Rule-Report AVP (AVP code 1018) inside of CCR-U.

When enabled: Gx interface between PCRF Nodal and PCRF Node will be able to perform the following : 

 

  • Trigger CCR-U which contains Charging-Rule-Report AVP(1018)

  • Each Charging-Rule-Report (1018) contains Charging-Rule-Name (string) extracts from Charging-Rule-Install AVP (AVP code 1001) inside of previous RAR message

  • Each Charging-Rule-Report (1018) contains Rule-Failure-Code (AVP code 1031) if there is failed Rule filtered by user-defined rule (based on regex)

Tcl parameter: TyCcClnRuleOperFailEn

Number of Rules

 

Enter up to 10 table entries. The table consists of a Rule name and Rule-Failure-code.

Range: 0 — 10

Default: 0

Tcl Parameter: TyCcClnRuleOperFailCnt

Rule Name

The Rule Name is a regular expression filter of a rule name that is required to match a rule name received from the PCRF in the RAR message.

Tcl Parameter: TyCcClnRuleOperFailEntry_1

Rule Failure Code

Select the Rule Failure Code value to simulate the PCRF nodal failing / rejecting the received rule.

Options: UNKNOWN_RULE_NAME(1), RATING_GROUP_ERROR(2), SERVICE_IDENTIFIER_ERROR(3), GW/PCEF_MALFUNCTION(4), RESOURCES_LIMITATIONS(5), MAX_NR_BEARERS_REACHED(6), UNKNOWN_BEARER_ID(7), MISSING_BEARER_ID(8)

 

 

 

^ Back to Top


APN Assignments

APN 0 ... APN 10

The values are enabled when you select Enable APN Assignemnts and the number of APN values fields (APN 0 — APN 10) are enabled based on the number of Default Bearers per Session you selected on the Test Configuration tab. Enter the APN Names as required.

Option: 2 - 50 characters (non incrementing field)

Tcl Parameter: TyCcClnApn0

(TyCcCInApn1, ....TyCcCInApn10)

 

 

^ Back to Top


Bearers

NOTE: Simulated Usage controls are not used in DRA Nodal test case, as it uses the  message flows and message timers to simulate what messages are sent and when they are sent.
Enable Simulated Usages

Select Simulate Usage to allow PCEF to simulate volumes used for uplink and/or downlink volumes of an active Bearer per usage interval. The PCEF accumulates the simulated usages and sends reports to PCRF when the accumulated volumes reach the usage threshold you imposed by PCRF.

NOTE: There is no actual data being sent or received for simulated usages.    The Gx Usage Monitoring feature is available only when your system is licensed for the feature.
Usage Interval

Indicates the period for which the PCEF simulate volumes used for uplink and/or downlink volumes of an active Bearer.

Tcl Parameter:

TyCcClnSimUsageEn TyCcClnSimUsageInterval

 

 

^ Back to Top


Default Bearers (D0)

The number of Default Bearers tabs (labeled D0, D1, ...Dn) available for configuration depends on the number of Default Bearers per Session you selected on the Test Configuration tab.

For default bearers, the PDN Connection Delays (Test Configuration tab) are set as the start delay for the first APN. PDN Activation Rate (Test Configuration tab) specifies the rate for starting all the default bearers, except the first one.

NOTE: The bearer timers (Bearer Establish after Session Established Timer and Bearer Teardown after Bearer Established Timer) are not used in DRA Nodal test case, as it uses the  message flows and message timers to simulate what messages are sent and when they are sent.

Bearer Establish after Session Established Timer

Enter the timer value (in seconds) for when the bearer sessions will be established. The establishment will cycle continuously for the duration of the test at the configured rates.

Tcl Parameter: TyCcClnBearerEstTimer_0

 

Bearer Teardown after Bearer Established Timer

Enter the timer value (in seconds) for when the bearer sessions will be torn down. The teardown will cycle continuously for the duration of the test at the configured rates.

Tcl Parameter: TyCcClnBearerTeardownTimer_0

 

UE Initiates Dedicated Bearers

Use UE Initiates Dedicated Bearers to indicate whether UE (or network) initiates dedicated bearers creation procedure. The parameter is available only when you select Dedicated Bearers per Default as > 0 on the Test Configuration tab

Tcl Parameter: TyCcClnUeInitsBearerEn_0

Values: True, False

 

Modify Bearers

Use the Modify Bearer to enable UEs to send requests to modify uplink/downlink values of previously established bearers.

  • Enter the time to wait after a Bearer is established before it can be modified.

Tcl Parameter:

TyCcClnBearerModTimerEn_0

TyCcClnBearerModTimer_0

  • Select Increment or Decrement and enter the appropriate value for Requested Uplink Bandwidth (bits/sec).

  • Select Increment or Decrement and enter the appropriate value for Requested Downlink Bandwidth (bits/sec).

Tcl Parameter:

TyCcClnBearerModUlChangeType_0

TyCcClnBearerModUlChange_0

TyCcClnBearerModDlChangeType_0

TyCcClnBearerModDlChange_0

 

NOTE: In PCRF Nodal and DRA Nodal test cases, Gx | PCC tab, in the Bearers tabs, the Include ARP and Include Aggregate Maximum Bit Rate appears on on the Default Bearer tabs (D0, D1, etc.)

NOTES:

  • Every CCR-I messages on Gx, sent by PCRF Nodal, DRA Nodal, and SGW Nodal test cases include
    Default-EPS-Bearer-QoS AVP with QCI and ARP, when configured on the GUI.
  • The QoS-Information AVP in CCR-I is not always sent and is only includes when ABR UL/DL is configured, and/or MBR UL/DL is configured.
 

Include ARP

Select Include ARP (Priority of Allocation and Retention) to determine the relative priority level during admission and congestion processes.

The primary purpose of ARP is to decide whether a bearer establishment/modification request is accepted or needs to be rejected in case of resource limitations (typically available radio capacity in case of GBR bearers). In addition, the ARP is also used (e.g. by the eNodeB) to decide which bearer(s) to drop during exceptional resource limitations (e.g. at handover). Once successfully established, a bearer's ARP does not have any impact on the bearer level packet forwarding treatment (e.g. scheduling and rate control).

Tcl Parameter: TyCcClnArpEn_0

Default:  False (enabler values: true/false)  

  • ARP Prirority Level

Tcl Parameter: TyCcClnArpValue_0

Range: 1 - 15

Default: 1

  • Pre-emption Capability: Select to include in the Default-EPS-Bearer-QoS AVP.

Tcl Parameter: TyCcClnArpPreemptCapEn_0

Default:  False (enabler values: true/false)  

  • Pre-emption Vulnerability:  Select to include in the Default-EPS-Bearer-QoS AVP.

Tcl Parameter: TyCcClnArpPreemptVulEn_0

Default:  False (enabler values: true/false)  

Include Aggregate Maximum Bit Rate  Information

The Aggregate Maximum Bit Rate Information element indicates the IP flow Aggregate Maximum Bit Rate for UL and DL traffic. The rate defined here applies to the established default bearers.

Tcl Parameter: TyCcClnAmbrEn_0

  • Downlink: TyCcClnAmbrDl_0

  • Uplink: TyCcClnAmbrUl_0

Packet Filters per Bearers

 

Select the number of packet Filters per Bearer for the Bearers per Session from the drop-down list.

Options: 0, 1, 2

Default: 1

  • Enter the appropriate value for Requested Uplink Bandwidth (bits/sec) of the filter data.

  • Enter the appropriate value for Requested Downlink Bandwidth (bits/sec) of the filter data.

Tcl Parameter:

TyCcClnReqQosMrbUL_0_0 TyCcClnReqQosMrbDL_0_0

 

QOS Class ID

The QOS Class ID for Charging Rules indicate the maximum authorized QOS class that may be defined for each Charging Rule. Enter the appropriate QOS Class ID and define the associated charging rules.

Tcl Parameter: TyCcClnReqQci_0

 

Filter

Enter Filter information, and User IP to Dest IP or Dest IP to User IP defined for the bearer.

  • Filter 1 defines the User IP to Destination IP

  • Filter 2 defines the Destination IP to User IP

  • User IP Extension is the text you enter in both Packet Filter 1 and Filter 2 tabs.

  • Precedence: The Precedence parameter defines the precedence of a PCC rule in case of overlapping PCC rules. A PCC rule with a lower value in the Precedence parameter with takes priority over a PCC rule with  a higher Precedence value.

The Precedence parameter is also used to indicate the evaluation precedence of the packet filters.

  • Overwrite User IP With Source IP: Select this option and enter the Source IP. The Source IP you enter here overwrites the Mobile IP. In addition, the Mobile IP is removed from packet filter in "Follow description" AVP.

  • Flow Label: Indicates the IPv6 flow label header (range 0 - 16777215 (24bits), default 0).

  • SPI: Indicates the security parameter index of the IPSec packet. Enter the appropriate value between 0 and 4294967295.

  • ToS: Indicates user-defined 2-octet ToS/Traffic class value. Enter an appropriate value between 0 and 65535.

Tcl Parameter:

TyCcClnFilter_0_0 TyCcClnFilterDestIp_0_0
TyCcClnUserIpExt_0_0 TyCcClnFilterPrec_0_0_
TyCcClnFilterFlowLabelEn_0_0 TyCcClnFilterFlowLabel_0_0
TyCcClnFilterSpiEn_0_0 TyCcClnFilterSpi_0_0
TyCcClnFilterTosEn_0_0 TyCcClnFilterTos_0_0

Simulated Usages

 

When you select Enable Simulated Usages in the Default Bearers sub-tab (s), the PCEF accumulates the simulated usages and sends reports to PCRF when the accumulated volume reaches the threshold you specified for Uplink and Downlink.

TyCcClnSimUsageUpVolEn_0

TyCcClnSimUsageUpVol_0
TyCcClnSimUsageDwnVolEn_0 TyCcClnSimUsageDwnVol_0

 

 

^ Back to Top


Dedicated Bearers per Default (D0-B0)

The number of Dedicated Bearers per Default tabs (labeled D0-B0, D1-B0, ...Dn-Bn) available for configuration depends on the number of Dedicated Bearers per Default you selected on the Test Configuration tab. Configure the rates, delays, uplink/downlink for packet filters.

Packet Filters per Bearers

 

Select the number of packet Filters per Bearer for the Bearers per Session from the drop-down list.

Options: 0, 1, 2

Default: 1

  • Enter the appropriate value for Requested Uplink Bandwidth (bits/sec) of the filter data.

  • Enter the appropriate value for Requested Downlink Bandwidth (bits/sec) of the filter data.

Tcl Parameter:

TyCcClnReqQosMrbUL_0_0 TyCcClnReqQosMrbDL_0_0

 

QOS Class ID

The QOS Class ID for Charging Rules indicate the maximum authorized QOS class that may be defined for each Charging Rule. Enter the appropriate QOS Class ID and define the associated charging rules.

Tcl Parameter: TyCcClnReqQci_0_0

 

Filter

Enter Filter information, and User IP to Dest IP or Dest IP to User IP defined for the bearer.

  • Filter 1 defines the User IP to Destination IP

  • Filter 2 defines the Destination IP to User IP

  • User IP Extension is the text you enter in both Packet Filter 1 and Filter 2 tabs.

  • Precedence: The Precedence parameter defines the precedence of a PCC rule in case of overlapping PCC rules. A PCC rule with a lower value in the Precedence parameter with takes priority over a PCC rule with  a higher Precedence value.

The Precedence parameter is also used to indicate the evaluation precedence of the packet filters.

  • Overwrite User IP With Source IP: Select this option and enter the Source IP. The Source IP you enter here overwrites the Mobile IP. In addition, the Mobile IP is removed from packet filter in "Follow description" AVP.

  • Flow Label: Indicates the IPv6 flow label header (range 0 - 16777215 (24bits), default 0).

  • SPI: Indicates the security parameter index of the IPSec packet. Enter the appropriate value between 0 and 4294967295.

  • ToS: Indicates user-defined 2-octet ToS/Traffic class value. Enter an appropriate value between 0 and 65535.

Tcl Parameter:

TyCcClnFilter_0_0 TyCcClnFilterDestIp_0_0_0
TyCcClnUserIpExt_0_0_0 TyCcClnFilterPrec_0_0_0
TyCcClnFilterFlowLabelEn_0_0_0 TyCcClnFilterFlowLabel_0_0_0
TyCcClnFilterSpiEn_0_0_0 TyCcClnFilterSpi_0_0_0
TyCcClnFilterTosEn_0_0_0 TyCcClnFilterTos_0_0_0

 

Simulated Usages

 

When you select Enable Simulated Usages in the Dedicated Bearers per Default sub-tab (s), the PCEF accumulates the simulated usages and sends reports to PCRF when the accumulated volume reaches the threshold you specified for Uplink and Downlink.

TyCcClnSimUsageUpVolEn_0_0

TyCcClnSimUsageUpVol_0_0
TyCcClnSimUsageDwnVolEn_0_0 TyCcClnSimUsageDwnVol_0_0

 

 

^ Back to Top