Sms Hlr Tab


The SMS HLR tab is used to define the information sent from the SMS to the HLR from the SMS Network test case.

 

 

Data Subscription

Teleservices

Regional Zones

 

Data Subscription

The Data Subscription allows you to configure timers to insert and delete Subscription data.  

Include 3Gpp Charging Characteristics

Use this checkbox to enable the type of charging for which the subscribed data is liable. Selected from one of 16 charging profiles.

First MAP operation sent from MSC/IWF

See table of Charging Profiles.

Range: 0 - 65535

Default: 0 (indicates that it is not used)

Tcl Parameter:

SmsHlrChargCharEn

SmsHlrChargChar

Update Location Process

Select the UpdateLocationRequest PostProcess.

Options : Return Result, Insert Subscriber Data

Tcl Parameter: SmsHlrUpdLocReqPostProcess

Include Aggregate Maximum Bit Rate

Select the checkbox and define the IP flow Aggregate Maximum Bit Rate for UL and DL traffic. The rate defined here applies to the data subscribed on the HLR.

Enter Max Downlink (bps) and Max Uplink (bps).

Range = 0 to 2147483647

Default value = 0

Tcl Parameter:

SmsHlrAmbrEn

SmsHlrAmbrMaxDlBps

SmsHlrAmbrMaxUlBps

Include Data Subscription Timer

Select the checkbox to enable entering the subscription insert and delete timers.

Tcl Parameter: SmsHlrIdrEn

IDR Time

Enter the time to wait (after a session is established) before sending and IDR message along with the Data Subscription information from the AVP Editor.

Tcl Parameter: SmsHlrIdrTime

 

Network Access Mode

Indicates the type of Network Access service allowed in the HSS; Packet and Circuit service; only Circuit or only Packet. Select the Network Access Mode allowed in the HLR from the dropdown list.

SmsHlrNtwkAccessModeEn

SmsHlrNtwkAccessMode

 

Access Restriction Data

The Access Restriction Data is permanent subscriber data stored in the HLR/HSS,.

 

Bit

Description

0

Enhanced Coverage Not Allowed

1

NB-IoT Not Allowed

2

HO-To-Non-3GPP-Access Not Allowed

3

WB-E-UTRAN Not Allowed

4

I-HSPA-Evolution Not Allowed

5

GAN Not Allowed

6

GERAN Not Allowed

7

UTRAN Not Allowed

 

SmsHlrAccessRestrictDataEn

SmsHlrAccessRestrictData

 

Include MPS-CSPriority

Select to include MPS-CSPriority.

Tcl Parameter: SmsHlrMpsCsPriorityEn

Include MPS-EPSPriority

Select to include MPS-EPSPriority.

Tcl Parameter: SmsHlrMpsEpsPriorityEn

Include Freeze TMSI

Select to include Freeze TMSI in PurgeMS response.

Tcl Parameter: SmsHlrFreezeTmsiEn

Include FreezeP TMSI

Select to include FreezeP TMSI in PurgeMS response.

Tcl Parameter: SmsHlrFreezePTmsiEn

Include FreezeM TMSI

Select to include FreezeM TMSI in PurgeMS response.

Tcl Parameter: SmsHlrFreezeMTmsiEn

Include Roaming Restricted Unsupported

Select to include in Update-Location-Answer message to indicate Roaming restricted due to unsupported feature.

Tcl Parameter: SmsHlrRoamingRestrictedUnsupported

 

RFSP Index

Select to include the RFSP (RAT-Frequency Selection Priority ID) AVP . In Update-Location-Answer message to include the subscribed value of Subscriber Profile ID for RAT/Frequency Priority.

Options: 1 to 256

Tcl Parameter:

SmsHlrRfspIndexEn

SmsHlrRfspIndexData

 

Trigger Command

Select to set the initiated MAP operation from HLR to IWF. When enabled, select the Trigger Command.

Options : CancelLocation, Reset

When CancelLocation is selected, include the Cancel Type parameter in MAP CancelLocation operation.

Options : updateProcedure,  subscriptionWithdraw, initialAttachProcedure

When CancelLocation is selected, select to include Type Of Update parameter in MAP CancelLocation operation

Options : sgsn-change,  mme-change

Tcl Parameter:

SmsHlrTriggerCmdEn

SmsHlrTriggerCmd

 

SmsHlrCancelType

SmsHlrTypeOfUpdEn

SmsHlrTypeOfUpd

STN-SR

Select to include the STN-SR in the ULA/ISR messages for SRVCC cases. If the STN-SR is present, it indicates the UE is SRVCC subscribed.

Options: 1 to 18 Characters

Tcl Parameter:

SmsHlrStnSrEn

SmsHlrStnSr

Operator Determined Barring

Select Operator Determined Barring and enter a value that indicates the services of a subscriber that are barred by the operator.

Tcl Parameter:

SmsHlrOpDeterminedBarEn

SmsHlrOpDeterminedBar

 

Option: 0 - 4294967294

Default: 0

Include APN OI Replacement

Select to include the APN-OI-Replacement AVP in Subscription-Data AVP for ULA and IDR messages.

Tcl Parameter:

SmsHlrApnOiRepEn

SmsHlrApnOiRep

MME Name

Select to include the MME name to be sent from VLR to HLR. Per 3GPP TS 29.002 section 8.8.1 MAP-INSERT-SUBSCRIBER-DATA.

MME name IE is included in the MAP-Insert-Subscriber-Data message.

Restoration Indicator IE is added to to MAP-Location-Update message and MAP-Restore IE message.

Enter 1 to 55 characters.

Default : mme.spirent.com

Tcl Parameter:

SmsHlrMmeNameEn

SmsHlrMmeName

Include Subscribed vSRVCC

Select to include the vSRVCC flag as part of the subscription data sent to the MME. If the subscriber is allowed to have vSRVCC in the VPLMN, then the HLR can it include if enabled.

 

Tcl Parameter:

SmsHlrSubsVsrvccEn

 

^ Back to Top

Regional Zones

The Regional-Subscription-Zone-Code AVP is defined as the tracking or routing areas into which the subscriber is allowed to roam.

Number of Zones

Indicates the subscription Zone code.

Option:  0 - 10

Default: 0

Tcl Parameter: SmsHlrNumZones

Zone n

Zone Code

 

The number of Zone tabs depends upon the number of Regional Zones selected.

Zone Code: Indicates the subscription Zone code. 0 - 65535 Default: 0 SmsHlrZoneCode_1

 

 

^ Back to Top

Teleservices

In insertSubscriberData, the teleserviceList IE is located in the MAP section.

Number of Teleservice Codes

Available in SMS Network when SMS-HLR and MAP-D are both enabled.

Enter the number Teleservice Codes.

In insertSubscriberData, the teleserviceList IE is located in the MAP section. 

Option:  0 - 20

Default: 0

Tcl Parameter: SmsHlrNumTeleSvcs

Teleservice n

Teleservice Code

Custom Code

The number of Teleservice tabs depends upon the "Number of Teleservice Codes" selected.

Per 3GPP 22.003.

The Teleservice Code column allows the selection of the spec-defined, single byte service codes and gives their names: 

Options:

00 - allTeleservices (default)

10 - allSpeechTransmisssionServices

11 - telephony

12 - emergencyCalls

20 - allShortMessageServices

21 - shortMessageMT-PP

22 - shortMessageMO-PP

23 - Cell Broadcast Service

60 - allFacsimileTransmissionServices

61 - facsimileGroup3AndAlterSpeech

62 - automaticfacsimileGroup3

63 - facsimileGroup4

70 - allDataTeleservices

80 - allTeleservices-ExceptSMS

90 - allVoiceGroupCallServices

91 - voiceGroupCall

92 - voiceBroadcastCall

D0 - allPLMN-specificTS

D1 - plmn-specificTS-1

D2 - plmn-specificTS-2

D3 - plmn-specificTS-3

D4 - plmn-specificTS-4

D5 - plmn-specificTS-5

D6 - plmn-specificTS-6

D7 - plmn-specificTS-7

D8 - plmn-specificTS-8

D9 - plmn-specificTS-9

DA - plmn-specificTS-A

DB - plmn-specificTS-B

DC - plmn-specificTS-C

DD - plmn-specificTS-D

DF - plmn-specificTS-F

Custom Value

SmsHlrTeleSvc_1
Custom Code

When "Custom Value" is selected for Teleservice Code , the Custom Code column is enabled for editing in that row.

The format is 1 to 5 HEX bytes (2, 4, 6, 8, or 10 HEX chars).

 

 

^ Back to Top