E2sm Ni Tab


The E2SM-Ni (E2 Service Model - Network Interface ) defines functionalities through E2 Network Interface procedures within xApps.

The interface that is designed for communication between DU/CU and Near-Real Time RIC is called E2. The protocol for the communication over E2 interface is called E2AP.

The E2SM-NI is available in RIC Node Test Case. 

Spec Reference : 

 

 

RIC Node

RIC Node

Event Trigger Style (Interface Message Event)

RIC Node

 

Related Measurements

Measurements collected for E2SM related processing are reported on the E2SM Measurements tab.


 

Number of Subscription Details

Select the Number of Subscription Details. Available in the RIC Node test case.

Range : 1 to 16

Default : 1

Tcl Parameters: E2smNiNumSubs

 

Subscription 

Event Trigger Style

Select the Event trigger Style.

Options : Interface Message Event

Tcl Parameters: E2smNiSubEvtTrigStyle_1

 

Interface Message Event

Available in the RIC Node test case when Event Trigger Style = Interface Message Event.

NI Type

Select the NI (Network Interface) Type. 

Options : X2, NG, Xn, F1, E1

Tcl Parameters: E2smNiSubEvtDefNiType_1

When NI (Network Interface) Type = X2, enter the following parameters:

Select the Node Type. Options : eNB

Enter the PLMN Identity. Range : 6 Hex characters, Default : 000000

Select the eNB ID Type. Options : Macro, Home, Short Macro, Long Macro

Enter the eNB ID. Range : 0 to 2097151, default : 0 

 

When NI (Network Interface) Type = NG or Xn or F1 or E1, enter the following parameters:

Select the NG-RAN Node Type. Options : gNB or ng-eNB (when type = Xn , F1 or E1). For type = ng-eNB, enter the ng-eNB ID Type (see eNB ID type above) and ng-eNB ID (see eNB ID above)

Enter the PLMN Identity. Range : 6 Hex characters, Default : 000000

Enter the Length. Range : 22 to 32,  Default : 22

Enter the gNB ID. Range : 0 to 4294967295, default : 0 

When NI (Network Interface) Type = F1, in addition to the parameters listed above, enter gNB-DU ID. Range : 0 to 68719476735, default : 0 

When NI (Network Interface) Type = E1, in addition to the parameters listed above, enter gNB-CU-UP ID. Range : 0 to 68719476735, default : 0 

 

Tcl Parameters: E2smNiSubEvtDefNiIdNodeType_1

Tcl Parameters: E2smNiSubEvtDefNiIdPlmnId_1

Tcl Parameters: E2smNiSubEvtDefNiIdEnbIdType_1

Tcl Parameters: E2smNiSubEvtDefNiIdEnbId_1

 

Tcl Parameters: E2smNiSubEvtDefNiIdNgRanNodeType_1

Tcl Parameters: E2smNiSubEvtDefNiIdGnbIdLen_1

Tcl Parameters: E2smNiSubEvtDefNiIdGnbId_1

Tcl Parameters: E2smNiSubEvtDefNiIdGnbDuId_1

Tcl Parameters: E2smNiSubEvtDefNiIdGnbCuUpId_1

NI Direction

Select the NI (Network Interface) Direction. 

Options : Incoming (default), Outgoing, Both

Tcl Parameters: E2smNiSubEvtDefNiDirection_1

Procedure Code

Select the NI (Network Interface) Procedure code. 

Range : 0 to 255

Default : 0

Tcl Parameters: E2smNiSubEvtDefNiMsgProcCode_1

Message Type

Select the NI (Network Interface) Message Type. 

Options : E2SM_NI_nothing (default), Incoming (default), E2SM_NI_initiating_message, E2SM_NI_successful_outcome, E2SM_NI_unsuccessful_outcome

Tcl Parameters: E2smNiSubEvtDefNiMsgType_1

Number of Protocol Tests

Select the maximum number of Network Interface Protocol Tests in event trigger definition supported by RAN Function.

Range : 0 to 15,

Default : 0

Enter the Message Protocol IE ID for each protocol test.

Tcl Parameters: E2smNiSubEvtDefTestNum_1

Tcl Parameters: E2smNiSubEvtDefMsgProtoIeId_1_1

 

Select the Number of Actions. Available in the RIC Node test case  when Event Trigger Style = Periodic.

Range : 1 to 16

Default : 1

Tcl Parameters: E2smNiSubNumActs_1

 

Actions 

 

Action Type

Select the Action Type.

Options : Report, Insert, Policy

Tcl Parameters: E2smNiSubActType_1_1

RIC Style Type

Select the RIC Style Type. Each RIC Style Type has its own Action Definition Format, which is described below.

Options :

Complete Message, Partial Message

Default : Complete Message

Tcl Parameters: E2smNiSubActStyleType_1_1

 

Action Type = Report

Sequence of RAN Parameters

This Sequence of RAN Parameters table is the same for either Complete or Partial Message. When Partial message is selected, enter the Target Protocol IE Identifier.

Range : 0 to 65535, default : 0

Click to add up to 255 RAN Parameters.

Enter the Parameter ID.

Enter the Parameter Value Type. Options : INTEGER,  ENUMERATED, BOOLEAN , BIT STRING , OCTET STRING , PRINTABLE STRING

Enter the Parameter Value. 

Values are validated based on the type selection listed here:

     INTEGER - Range : 0-4294967295

    ENUMERATED - Range : 0-4294967295

    BOOLEAN - Range : 0-4294967295

    BIT STRING- format: [#bits]-[hex chars], example: 16-A0FB (max 256 bits)

    OCTET STRING - up to 256 Hex characters

    PRINTABLE STRING - up to 256 ASCII characters

Tcl Parameters: E2smNiSubActTgtProtoIeId_1_1

Tcl Parameters: E2smNiSubActRptParamsNum_1_1_1

Tcl Parameters: E2smNiSubActRptParamsId_1_1_1

Tcl Parameters: E2smNiSubActRptParamsValueType_1_1_1

Tcl Parameters: E2smNiSubActRptParamsValue_1_1_1

 

Action Type = Policy - Message Administration

Number of RAN UE Groups

Enter up to 10 RAN UE Groups for Policy Message Administration.

Range : 0 to 10

Default : 0

Tcl Parameters: E2smNiSubActRanUeGrpNum_1_1

RAN UE Group ID

For each RAN UE Group, enter the RAN UE Group ID for Policy Message Administration.

Range : 0 to 255

Default : 0

Tcl Parameters: E2smNiSubActRanUeGrpId_1_1_1

RAN Parameters

For each RAN UE Group, enter the RAN Parameters for Policy Message Administration.

 

Click to add up to 255 RAN Parameters.

Enter the Parameter ID.

Enter the Test Condition. Options : equal, greaterthan, lessthan, contains, present

Enter the Parameter Value Type. Options : INTEGER,  ENUMERATED, BOOLEAN , BIT STRING , OCTET STRING , PRINTABLE STRING

Enter the Parameter Value. 

Values are validated based on the type selection listed here:

     INTEGER - Range : 0-4294967295

    ENUMERATED - Range : 0-4294967295

    BOOLEAN - Range : 0-4294967295

    BIT STRING- format: [#bits]-[hex chars], example: 16-A0FB (max 256 bits)

    OCTET STRING - up to 256 Hex characters

    PRINTABLE STRING - up to 256 ASCII characters

 

Tcl Parameters: E2smNiSubActRanUeGrpParamsNum_1_1_1

Tcl Parameters: E2smNiSubActRanUeGrpParamsId_1_1_1_1

Tcl Parameters: E2smNiSubActRanUeGrpParamsCond_1_1_1_1

Tcl Parameters: E2smNiSubActRanUeGrpParamsValueType_1_1_1

Tcl Parameters: E2smNiSubActRanUeGrpParamsValue_1_1_1

RAN Imperative Policy

For each RAN UE Group, enter the RAN Imperative Policy Parameters for Policy Message Administration.

 

Click to add up to 255 RAN Imperative Policy Parameters.

Enter the Parameter ID.

Enter the Parameter Value Type. Options : INTEGER,  ENUMERATED, BOOLEAN , BIT STRING , OCTET STRING , PRINTABLE STRING

Enter the Parameter Value. 

Values are validated based on the type selection listed here:

     INTEGER - Range : 0-4294967295

    ENUMERATED - Range : 0-4294967295

    BOOLEAN - Range : 0-4294967295

    BIT STRING- format: [#bits]-[hex chars], example: 16-A0FB (max 256 bits)

    OCTET STRING - up to 256 Hex characters

    PRINTABLE STRING - up to 256 ASCII characters

 

Tcl Parameters: E2smNiSubActRanUeGrpPolicyNum_1_1_1

Tcl Parameters: E2smNiSubActRanUeGrpPolicyId_1_1_1_1

Tcl Parameters: E2smNiSubActRanUeGrpPolicyValueType_1_1_1

Tcl Parameters: E2smNiSubActRanUeGrpPolicyValue_1_1_1

 

Action Type = Insert - Complete Message

Subsequent Action

Enable Subsequent Action to select the Action Type and the Time to Wait.

Select the Action Type. Options : Continue (default), Halt

Select the Time to Wait.

Options : 1ms, 2ms, 5ms, 10ms, 20ms, 30ms, 40ms, 50ms,  100ms, 200ms, 500ms, 1s, 2s, 5s, 10s, 20s, 60s

Tcl Parameters: E2smNiSubActInsertSubActEn_1_1

Tcl Parameters: E2smNiSubActInsertSubActType_1_1

Tcl Parameters: E2smNiSubActInsertSubActWaitTime_1_1

Following Control

Enter the Control Message Priority. Range : 0 to 5, default : 0

Select the Control Ack Request. Options : NoAck (default), Ack

Tcl Parameters: E2smNiSubActInsertMsgPriority_1_1

Tcl Parameters: E2smNiSubActInsertCtrlAckReqEn_1_1

Tcl Parameters: E2smNiSubActInsertCtrlAckReq_1_1

 

Number of Control Details

Select the Number of Control Details. Available in the RIC Node test case.

Range : 1 to 16

Default : 1

Tcl Parameters: E2smNiNumCtrls

 

Control 

RIC Style Type

Select the RIC Style Type.

Options : Complete Message

Tcl Parameters: E2smNiCtrlStyle_1

 

Complete Message

Available in the RIC Node test case when RIC Style Type =Complete Message.

NI Type

Select the NI (Network Interface) Type. 

Options : X2, NG, Xn, F1, E1

Tcl Parameters: E2smNiCtrlNiType_1

When NI (Network Interface) Type = X2, enter the following parameters:

Select the Node Type. Options : eNB

Enter the PLMN Identity. Range : 6 Hex characters, Default : 000000

Select the eNB ID Type. Options : Macro, Home, Short Macro, Long Macro

Enter the eNB ID. Range : 0 to 2097151, default : 0 

 

When NI (Network Interface) Type = NG or Xn or F1 or E1, enter the following parameters:

Select the NG-RAN Node Type. Options : gNB or ng-eNB (when type = Xn , F1 or E1). For type = ng-eNB, enter the ng-eNB ID Type (see eNB ID type above) and ng-eNB ID (see eNB ID above)

Enter the PLMN Identity. Range : 6 Hex characters, Default : 000000

Enter the Length. Range : 22 to 32,  Default : 22

Enter the gNB ID. Range : 0 to 4294967295, default : 0 

When NI (Network Interface) Type = F1, in addition to the parameters listed above, enter gNB-DU ID. Range : 0 to 68719476735, default : 0 

When NI (Network Interface) Type = E1, in addition to the parameters listed above, enter gNB-CU-UP ID. Range : 0 to 68719476735, default : 0 

 

Tcl Parameters: E2smNiCtrlNiIdNodeType_1

Tcl Parameters: E2smNiCtrlNiIdPlmnId_1

Tcl Parameters: E2smNiCtrlNiIdEnbIdType_1

Tcl Parameters: E2smNiCtrlNiIdEnbId_1

 

Tcl Parameters: E2smNiCtrlNiIdNgRanNodeType_1

Tcl Parameters: E2smNiCtrlNiIdGnbIdLen_1

Tcl Parameters: E2smNiCtrlNiIdGnbId_1

Tcl Parameters: E2smNiCtrlNiIdGnbDuId_1

Tcl Parameters: E2smNiCtrlNiIdGnbCuUpId_1

NI Direction

Select the NI (Network Interface) Direction. 

Options : Incoming (default), Outgoing, Both

Tcl Parameters: E2smNiCtrlNiDirection_1

Message Priority

Select the Message Priority. 

Range : 0 to 4294967295

Default : 0

Tcl Parameters: E2smNiCtrlMsgPriority_1

Control Ack Request

Enable to select the Control Ack Request. 

Options : NoAck (default), Ack

Tcl Parameters: E2smNiCtrlAckReqEn_1

Tcl Parameters: E2smNiCtrlAckReq_1

^ Back to Top